Showing papers on "Ultimate tensile strength published in 2014"

Mechanical characterization of bulk Sylgard 184 for microfluidics and microengineering

Abstract: Polydimethylsiloxane (PDMS) elastomers are extensively used for soft lithographic replication of microstructures in microfluidic and micro-engineering applications. Elastomeric microstructures are commonly required to fulfil an explicit mechanical role and accordingly their mechanical properties can critically affect device performance. The mechanical properties of elastomers are known to vary with both curing and operational temperatures. However, even for the elastomer most commonly employed in microfluidic applications, Sylgard 184, only a very limited range of data exists regarding the variation in mechanical properties of bulk PDMS with curing temperature. We report an investigation of the variation in the mechanical properties of bulk Sylgard 184 with curing temperature, over the range 25 ◦ C to 200 ◦ C. PDMS samples for tensile and compressive testing were fabricated according to ASTM standards. Data obtained indicates variation in mechanical properties due to curing temperature for Young’s modulus of 1.32‐2.97 MPa, ultimate tensile strength of 3.51‐7.65 MPa, compressive modulus of 117.8‐186.9 MPa and ultimate compressive strength of 28.4‐51.7 GPa in a range up to 40% strain and hardness of 44‐54 ShA.

A Review of Dynamic Experimental Techniques and Mechanical Behaviour of Rock Materials

Abstract: The purpose of this review is to discuss the development and the state of the art in dynamic testing techniques and dynamic mechanical behaviour of rock materials. The review begins by briefly introducing the history of rock dynamics and explaining the significance of studying these issues. Loading techniques commonly used for both intermediate and high strain rate tests and measurement techniques for dynamic stress and deformation are critically assessed in Sects. 2 and 3. In Sect. 4, methods of dynamic testing and estimation to obtain stress–strain curves at high strain rate are summarized, followed by an in-depth description of various dynamic mechanical properties (e.g. uniaxial and triaxial compressive strength, tensile strength, shear strength and fracture toughness) and corresponding fracture behaviour. Some influencing rock structural features (i.e. microstructure, size and shape) and testing conditions (i.e. confining pressure, temperature and water saturation) are considered, ending with some popular semi-empirical rate-dependent equations for the enhancement of dynamic mechanical properties. Section 5 discusses physical mechanisms of strain rate effects. Section 6 describes phenomenological and mechanically based rate-dependent constitutive models established from the knowledge of the stress–strain behaviour and physical mechanisms. Section 7 presents dynamic fracture criteria for quasi-brittle materials. Finally, a brief summary and some aspects of prospective research are presented.

Evading the strength–ductility trade-off dilemma in steel through gradient hierarchical nanotwins

Abstract: The strength-ductility trade-off has been a long-standing dilemma in materials science. This has limited the potential of many structural materials, steels in particular. Here we report a way of enhancing the strength of twinning-induced plasticity steel at no ductility trade-off. After applying torsion to cylindrical twinning-induced plasticity steel samples to generate a gradient nanotwinned structure along the radial direction, we find that the yielding strength of the material can be doubled at no reduction in ductility. It is shown that this evasion of strength-ductility trade-off is due to the formation of a gradient hierarchical nanotwinned structure during pre-torsion and subsequent tensile deformation. A series of finite element simulations based on crystal plasticity are performed to understand why the gradient twin structure can cause strengthening and ductility retention, and how sequential torsion and tension lead to the observed hierarchical nanotwinned structure through activation of different twinning systems.

Microstructure and mechanical properties of Al-12Si produced by selective laser melting: Effect of heat treatment

Abstract: Al-12Si specimens are produced by selective laser melting (SLM) from gas atomized powders. An extremely fine cellular structure is observed with residual free Si along the cellular boundaries. Room temperature tensile tests reveal a remarkable mechanical behavior: the samples show yield and tensile strengths of about 260. MPa and 380. MPa, respectively, along with fracture strain of ~3%. The effect of annealing on microstructure and related tensile properties is examined and the results demonstrate that the mechanical behavior of the Al-12Si SLM samples can be tuned within a wide range of strength and ductility through proper annealing treatment.

Properties of strain hardening ultra high performance fiber reinforced concrete (UHP-FRC) under direct tensile loading

Abstract: Enhanced matrix packing density and tailored fiber-to-matrix interface bond properties have led to the recent development of ultra-high performance fiber reinforced concrete (UHP-FRC) with improved material tensile performance in terms of strength, ductility and energy absorption capacity. The objective of this research is to experimentally investigate and analyze the uniaxial tensile behavior of the new material. The paper reviews and categorizes a variety of tensile test setups used by other researchers and presents a revised tensile set up tailored to obtain reliable results with minimal preparation effort. The experimental investigation considers three types of steel fibers, each in three different volume fractions. Elastic, strain hardening and softening tensile parameters, such as first cracking stress and strain, elastic and strain hardening modulus, composite strength and energy dissipation capacity, of the UHP-FRCs are characterized, analyzed and linked to the crack pattern observed by microscopic analysis. Models are proposed for representing the tensile stress–strain response of the material.

Study on mechanical and wear properties of Al 7075/Al2O3/graphite hybrid composites

Abstract: This work investigated the influence of graphite on the wear behavior of Al 7075/Al 2 O 3 /5 wt.% graphite hybrid composite. The investigation reveals the effectiveness of incorporation of graphite in the composite for gaining wear reduction. The Al 7075 (aluminium alloy 7075) reinforced with Al 2 O 3 –graphite were investigated. The composites were fabricated using liquid metallurgy route. Ceramic particles along with solid lubricating materials were incorporated into aluminium alloy matrix to accomplish reduction in both wear resistance and coefficient of friction. The Al 7075/Al 2 O 3 /graphite hybrid composite was prepared with 5 wt.% graphite particles addition and 2, 4, 6 and 8 wt.% of Al 2 O 3 . The hardness, tensile strength, flexural strength and compression strength of the Al 7075–Al 2 O 3 –graphite hybrid composites are found to be increased by increased weight percentage of ceramic phase. The wear properties of the hybrid composites containing graphite exhibited the superior wear-resistance properties.

Fracture initiation and propagation in intact rock – A review

Abstract: The initiation and propagation of failure in intact rock are a matter of fundamental importance in rock engineering. At low confining pressures, tensile fracturing initiates in samples at 40%–60% of the uniaxial compressive strength and as loading continues, and these tensile fractures increase in density, ultimately coalescing and leading to strain localization and macro-scale shear failure of the samples. The Griffith theory of brittle failure provides a simplified model and a useful basis for discussion of this process. The Hoek–Brown failure criterion provides an acceptable estimate of the peak strength for shear failure but a cutoff has been added for tensile conditions. However, neither of these criteria adequately explains the progressive coalition of tensile cracks and the final shearing of the specimens at higher confining stresses. Grain-based numerical models, in which the grain size distributions as well as the physical properties of the component grains of the rock are incorporated, have proved to be very useful in studying these more complex fracture processes.

Fracture Surface Analysis of 3D-Printed Tensile Specimens of Novel ABS-Based Materials

Abstract: One of the most common materials utilized by material extrusion 3D printing is acrylonitrile butadiene styrene (ABS). The work presented in this research explored the effect of the addition of reinforcing materials on the mechanical properties of ABS in an effort to create materials with enhanced physical properties. A comparison was made between pure ABS, two ABS matrix composites, and one ABS/elastomer blend with the purpose of characterizing the effect of additives on the mechanical properties. Tensile test results of specimens built in different orientations showed that ABS reinforced with 5% by weight TiO2 exhibited the highest ultimate tensile strength for specimens built in both horizontal and vertical directions with 32.2 and 18.4 MPa, respectively. The compounding of an elastomeric material with ABS improved the surface finish of parts as they were visibly smoother compared to those printed from the ABS baseline material, though there was an observable decrease in the ductility of tensile specimens. Analysis was performed on the fracture surface of the tensile specimens through the use of scanning electron microscopy. Fractography revealed different modes of failure related to the different additives. The effects of additives on the anisotropy associated with the mechanical properties of 3D-printed parts were also analyzed.

A Review of the Tensile Strength of Rock: Concepts and Testing

Abstract: A review of the tensile strength of rock was conducted to determine the relationship between direct tensile strength (DTS) and Brazilian tensile strength (BTS) and to examine the validity of estimating tensile strength from other measured properties, such as the crack initiation (CI) threshold. A data set was gathered from the existing literature where tensile values could be reliably correlated with unconfined compressive strength or CI values. It was determined that the BTS obtained in standard testing is generally greater than the equivalent DTS and that this relationship is rock type dependent. CI yields a reasonable estimate of tensile strength and this correlation is improved when the BTS values are reduced to DTS values by rock type specific correlations. The factor f, in DTS = f BTS, can be considered to be approximately 0.9 for metamorphic, 0.8 for igneous and 0.7 for sedimentary rocks. The relationships presented demonstrate that there is wide scatter in the available data for estimating tensile strength likely due to both specimen variability and testing configuration, including platen geometry and relative stiffness. Estimates of tensile strength should only be used for preliminary design purposes and measurements should be made to confirm preliminary assumptions for each design.

High-strength carbon nanotube fibre-like ribbon with high ductility and high electrical conductivity

Abstract: There is strong interest in carbon nanotube assemblies for a variety of applications, many of which require combined high mechanical and electrical properties. Here, the authors demonstrate a rolling technique for performance improvement, reporting tensile strength of 4.34 GPa, ductility of 10% and electrical conductivity of 2.0 × 104 S cm−1.