Ultimate tensile strength

About: Ultimate tensile strength is a research topic. Over the lifetime, 129285 publications have been published within this topic receiving 2123768 citations. The topic is also known as: UTS & tensile strength.

Ultrahigh strength and high electrical conductivity in copper

Abstract: Methods used to strengthen metals generally also cause a pronounced decrease in electrical conductivity, so that a tradeoff must be made between conductivity and mechanical strength. We synthesized pure copper samples with a high density of nanoscale growth twins. They showed a tensile strength about 10 times higher than that of conventional coarse-grained copper, while retaining an electrical conductivity comparable to that of pure copper. The ultrahigh strength originates from the effective blockage of dislocation motion by numerous coherent twin boundaries that possess an extremely low electrical resistivity, which is not the case for other types of grain boundaries.

High tensile ductility in a nanostructured metal.

Abstract: Nanocrystalline metals--with grain sizes of less than 100 nm--have strengths exceeding those of coarse-grained and even alloyed metals, and are thus expected to have many applications. For example, pure nanocrystalline Cu (refs 1-7) has a yield strength in excess of 400 MPa, which is six times higher than that of coarse-grained Cu. But nanocrystalline materials often exhibit low tensile ductility at room temperature, which limits their practical utility. The elongation to failure is typically less than a few per cent; the regime of uniform deformation is even smaller. Here we describe a thermomechanical treatment of Cu that results in a bimodal grain size distribution, with micrometre-sized grains embedded inside a matrix of nanocrystalline and ultrafine (<300 nm) grains. The matrix grains impart high strength, as expected from an extrapolation of the Hall-Petch relationship. Meanwhile, the inhomogeneous microstructure induces strain hardening mechanisms that stabilize the tensile deformation, leading to a high tensile ductility--65% elongation to failure, and 30% uniform elongation. We expect that these results will have implications in the development of tough nanostructured metals for forming operations and high-performance structural applications including microelectromechanical and biomedical systems.

Mechanical properties of nylon 6-clay hybrid

Abstract: Various nylon 6-clay hybrids, such as molecular composites of nylon 6 and silicate layers of montmorillonite and saponite, NCH's and NCHP's, respectively, have been synthesized. To estimate the mechanical properties of these hybrids, tensile, flexural, impact, and heat distortion tests were carried out. NCH was found superior in strength and modulus and comparable in impact strength to nylon 6. The heat distortion temperature (HDT) of NCH (montmorillonite: 4.7 wt. %) was 152 °C, which was 87 °C higher than that of nylon 6. In NCHP, saponite had a smaller effect on the increase of these mechanical properties. The modulus and HDT of NCH and NCHP increased with an increase in the amount of clay minerals. It was found that these properties were well described by the contribution of the constrained region calculated from the storage and loss modulus at the glass transition temperature. According to the mixing law on elastic modulus, the following expression was obtained between the modulus E at 120 °C and the fraction of the constrained region C, En = Ecn = C, where the values of n and Ec (modulus of the constrained region) were 0.685 and 1.02 GPa, respectively.

Enhanced mechanical properties of nanocomposites at low graphene content.

Abstract: In this study, the mechanical properties of epoxy nanocomposites with graphene platelets, single-walled carbon nanotubes, and multi-walled carbon nanotube additives were compared at a nanofiller weight fraction of 0.1 ± 0.002%. The mechanical properties measured were the Young’s modulus, ultimate tensile strength, fracture toughness, fracture energy, and the material’s resistance to fatigue crack propagation. The results indicate that graphene platelets significantly out-perform carbon nanotube additives. The Young’s modulus of the graphene nanocomposite was ∼31% greater than the pristine epoxy as compared to ∼3% increase for single-walled carbon nanotubes. The tensile strength of the baseline epoxy was enhanced by ∼40% with graphene platelets compared to ∼14% improvement for multi-walled carbon nanotubes. The mode I fracture toughness of the nanocomposite with graphene platelets showed ∼53% increase over the epoxy compared to ∼20% improvement for multi-walled carbon nanotubes. The fatigue resistance resu...