VLSI Test Principles and Architectures: Design for Testability (Systems on Silicon)

This book is a comprehensive guide to new DFT methods that will show the readers how to design a testable and quality product, drive down test cost, improve product quality and yield, and speed up time-to-market and time-to-volume.

· Most up-to-date coverage of design for testability. 
· Coverage of industry practices commonly found in commercial DFT tools but not discussed in other books. 
· Numerous, practical examples in each chapter illustrating basic VLSI test principles and DFT architectures.
· Lecture slides and exercise solutions for all chapters are now available.
· Instructors are also eligible for downloading PPT slide files and MSWORD solutions files from the manual website.

Table of Contents

Chapter 1 - Introduction
Chapter 2 - Design for Testability
Chapter 3 - Logic and Fault Simulation 
Chapter 4 - Test Generation 
Chapter 5 - Logic Built-In Self-Test
Chapter 6 - Test Compression
Chapter 7 - Logic Diagnosis
Chapter 8 - Memory Testing and Built-In Self-Test
Chapter 9 - Memory Diagnosis and Built-In Self-Repair
Chapter 10 - Boundary Scan and Core-Based Testing
Chapter 11 - Analog and Mixed-Signal Testing
Chapter 12 - Test Technology Trends in the Nanometer Age

VLSI Test Principles and Architectures: Design for Testability

When the response to a test vector is captured by state elements in scan based tests, the switching activity of the circuit may be large resulting in abnormal power dissipation and supply current demand High supply current may cause excessive supply voltage droops leading to larger gate delays which may cause good chips to fail tests This paper presents a scalable approach called Preferred Fill to reduce average and peak power dissipation during capture cycles of launch off capture delay fault tests Experimental results presented for benchmark and industrial circuits demonstrate the effectiveness of the proposed method

Preferred Fill: A Scalable Method to Reduce Capture Power for Scan Based Designs

Modern electronics testing has a legacy of more than 40 years. The introduction of new technologies, especially nanometer technologies with 90nm or smaller geometry, has allowed the semiconductor industry to keep pace with the increased performance-capacity demands from consumers. As a result, semiconductor test costs have been growing steadily and typically amount to 40% of today's overall product cost. 

This book is a comprehensive guide to new VLSI Testing and Design-for-Testability techniques that will allow students, researchers, DFT practitioners, and VLSI designers to master quickly System-on-Chip Test architectures, for test debug and diagnosis of digital, memory, and analog/mixed-signal designs.

KEY FEATURES
* Emphasizes VLSI Test principles and Design for Testability architectures, with numerous illustrations/examples.
* Most up-to-date coverage available, including Fault Tolerance, Low-Power Testing, Defect and Error Tolerance, Network-on-Chip (NOC) Testing, Software-Based Self-Testing, FPGA Testing, MEMS Testing, and System-In-Package (SIP) Testing, which are not yet available in any testing book.
* Covers the entire spectrum of VLSI testing and DFT architectures, from digital and analog, to memory circuits, and fault diagnosis and self-repair from digital to memory circuits.
* Discusses future nanotechnology test trends and challenges facing the nanometer design era; promising nanotechnology test techniques, including Quantum-Dots, Cellular Automata, Carbon-Nanotubes, and Hybrid Semiconductor/Nanowire/Molecular Computing.
* Practical problems at the end of each chapter for students.

System-on-Chip Test Architectures: Nanometer Design for Testability

Scan-based at-speed testing is a key technology to guarantee timing-related test quality in the deep submicron era. However, its applicability is being severely challenged since significant yield loss may occur from circuit malfunction due to excessive IR drop caused by high power dissipation when a test response is captured. This paper addresses this critical problem with a novel low-capture-power X-filling method of assigning 0's and 1's to unspecified (X) bits in a test cube obtained during ATPG. This method reduces the circuit switching activity in capture mode and can be easily incorporated into any test generation flow to achieve capture power reduction without any area, timing, or fault coverage impact. Test vectors generated with this practical method greatly improve the applicability of scan-based at-speed testing by reducing the risk of test yield loss

Low-capture-power test generation for scan-based at-speed testing

Research on low-power scan testing has been focused on the shift mode, with little or no consideration given to the capture mode power. However, high switching activity when capturing a test response can cause excessive IR drop, resulting in significant yield loss. This paper addresses this problem with a novel low-capture-power X-filling method by assigning 0's and 1's to unspecified (X) bits in a test cube to reduce the switching activity in capture mode. This method can be easily incorporated into any test generation flow, where test cubes are obtained during ATPG or by X-bit identification. Experimental results show the effectiveness of this method in reducing capture power dissipation without any impact on area, timing, and fault coverage.

/pdf/on-low-capture-power-test-generation-for-scan-testing-wm7ivy9gwr.pdf

Y. Yamashita

Papers

On low-capture-power test generation for scan testing

Low-capture-power test generation for scan-based at-speed testing