http://compalg.inf.elte.hu/~tony/Kutatas/BinPacking/Johnson-BinPacking-NP-Column-JAlg-2002.pdf

The NP-completeness column: An ongoing guide

In the layout design of LSI chips, channel routing is one of the key problems. The problem is to route a specified net list between two rows of terminals across a two-layer channel. Nets are routed with horizontal segments on one layer and vertical segments on the other. Connections between two layers are made through via holes. Two new algorithms are proposed. These algorithms merge nets instead of assigning horizontal tracks to individual nets. The algorithms were coded in Fortran and implemented on a VAX 11/780 computer. Experimental results are quite encouraging. Both programs generated optimal solutions in 6 out of 8 cases, using examples in previously published papers. The computation times of the algorithms for a typical channel (300 terminals, 70 nets) are 1.0 and 2.1 s, respectively.

Efficient Algorithms for Channel Routing

This paper presents an algorithm for interconnecting two sets of terminals across an intervening channel. It is assumed that the routing is done on two distinct levels with all horizontal paths being assigned to one level and all vertical paths to the other. Connections between the levels are made through contact windows. A single net may result in many horizontal and vertical segments. Experimental results indicate that this algorithm is very successful in routing channels that contain severe constraints. Usually, the routing is accomplished within one track of the mathematical lower bound. The routing algorithm presented here was developed as part of LTX, a computer-aided design system for integrated circuit layout and was implemented on an HP-2100 minicomputer. A typical channel (300 terminals, 100 nets) can be routed in less than 5 seconds. Routing results are presented both for polycell chips under development at Bell Laboratories and for examples that exist in the published literature. For the latter, reductions of 10% in the wiring area were typical.

A “DOGLEG” channel router

This paper describes the REAL REgister ALlocation program. REAL uses a track assignment algorithm taken from channel routing called the Left Edge algorithm. REAL is optimal for non-pipelined designs with no conditional branches. It is thought that REAL is also optimal for designs with conditional branches, pipelined or not. Experimental results are included in the report, which illustrate the optimal solutions found by REAL. REAL is part of the ADAM Advanced Design AutoMation system, and will be used to process designs output from MAHA and Sehwa.

REAL: A Program for REgister ALlocation

We present a new, "greedy", channel-router that is quick, simple, and highly effective. It always succeeds, usually using no more than one track more than required by channel density. (It may be forced in rare cases to make a few connections "off the end" of the channel, in order to succeed.) It assumes that all pins and wiring lie on a common grid, and that vertical wires are on one layer, horizontal on another. The greedy router wires up the channel in a left-to-right, column-by-column manner, wiring each column completely before starting the next. Within each column the router tries to maximize the utility of the wiring produced, using simple, "greedy" heuristics. It may place a net on more than one track for a few columns, and "collapse" the net to a single track later on, using a vertical jog. It may also use a jog to move a net to a track closer to its pin in some future column. The router may occasionally add a new track to the channel, to avoid "getting stuck".

/pdf/a-greedy-channel-router-41070bu05d.pdf

A "Greedy" Channel Router

The purpose of this paper is to introduce a new wire routing method for two layer printed circuit boards. This technique has been developed at the University of Illinois Center for Advanced Computation and has been programmed in ALGOL for a B5500 computer. The routing method is based on the newly developed channel assignment algorithm and requires many via holes. The primary goals of the method are short execution time and high wireability. Actual design specifications for ILLIAC IV Control Unit boards have been used to test the feasibility of the routing technique. Tests have shown that this algorithm is very fast and can handle large boards.

Akihiro Hashimoto

Papers

Wire routing by optimizing channel assignment within large apertures