Ferrimagnets having low RF loss are used in passive microwave components such as isolators, circulators, phase shifters, and miniature antennas operating in a wide range of frequencies (1–100 GHz) and as magnetic recording media owing to their novel physical properties. Frequency tuning of these components has so far been obtained by external magnetic fields provided by a permanent magnet or by passing current through coils. However, for high frequency operation the permanent part of magnetic bias should be as high as possible, which requires large permanent magnets resulting in relatively large size and high cost microwave passive components. A promising approach to circumvent this problem is to use hexaferrites, such as BaFe12O19 and SrFe12O19, which have high effective internal magnetic anisotropy that also contributes to the permanent bias. Such a self-biased material remains magnetized even after removing the external applied magnetic field, and thus, may not even require an external permanent magnet. In garnet and spinel ferrites, such as Y3Fe5O12 (YIG) and MgFe2O4, however, the uniaxial anisotropy is much smaller, and one would need to apply huge magnetic fields to achieve such high frequencies. In Part 1 of this review of microwave ferrites a brief discussion of fundamentals of magnetism, particularly ferrimagnetism, and chemical, structural, and magnetic properties of ferrites of interest as they pertain to net magnetization, especially to self biasing, are presented. Operational principles of microwave passive components and electrical tuning of magnetization using magnetoelectric coupling are discussed in Part 2.

/pdf/microwave-ferrites-part-1-fundamental-properties-124qghgxm4.pdf

Microwave ferrites, part 1: fundamental properties

Synthesis of cobalt ferrite (CoFe2O4) nanoparticles using combustion, coprecipitation, and precipitation methods: A comparison study of size, structural, and magnetic properties

Presently, there is interest in making medical devices such as expandable stents and intravascular microactuators from shape memory polymer (SMP). One of the key challenges in realizing SMP medical devices is the implementation of a safe and effective method of thermally actuating various device geometries in vivo. A novel scheme of actuation by Curie-thermoregulated inductive heating is presented. Prototype medical devices made from SMP loaded with nickel zinc ferrite ferromagnetic particles were actuated in air by applying an alternating magnetic field to induce heating. Dynamic mechanical thermal analysis was performed on both the particle-loaded and neat SMP materials to assess the impact of the ferrite particles on the mechanical properties of the samples. Calorimetry was used to quantify the rate of heat generation as a function of particle size and volumetric loading of ferrite particles in the SMP. These tests demonstrated the feasibility of SMP actuation by inductive heating. Rapid and uniform heating was achieved in complex device geometries and particle loading up to 10% volume content did not interfere with the shape recovery of the SMP

/pdf/inductively-heated-shape-memory-polymer-for-the-magnetic-21e6df8uxb.pdf

Inductively Heated Shape Memory Polymer for the Magnetic Actuation of Medical Devices

Effect of cobalt substitution on structural, magnetic and electric properties of nickel ferrite

Nickel ferrite, a kind of soft magnetic materials is one of the most attracting class of materials due to its interesting and important properties and has many technical applications, such as in catalysis, sensors and so on. In this paper the synthesis of NiFe2O4 nanoparticles by the hydrothermal method is reported and the inhibition of surfactant (Glycerol or Sodium dodecyl sulfate) on the particles growth is investigated. For investigation of the inhibition effect of surfactant on NiFe2O4 particles growth, the samples were prepared in presence of Glycerol and Sodium dodecyl sulfate. The X-ray powder diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), vibrating sample magnetometer (VSM) and inductively coupled plasma atomic emission spectrometer (ICP-AES) techniques were used to characterize the samples. The results of XRD and ICP-AES show that the products were pure NiFe2O4 and also nanoparticles grow with increasing the temperature, while surfactant prevents the particle growth under the same condition. The average particle size was determined from the Scherrer's equation and TEM micrographs and found to be in the range of 50-60 nm that decreased up to 10-15 nm in presence of surfactant. The FT-IR results show two absorption bands near to 603 and 490 cm-1 for the tetrahedral and octahedral sites respectively. Furthermore, the saturated magnetization and coercivity of NiFe2O4 nanoparticles were in the range of 39.60 emu/g and 15.67 Qe that decreased for samples prepared in presence of surfactant. As well as, the nanoparticles exhibited a superparamagnetic behavior at room temperature. Nanosized nickel ferrite particles were synthesized with and without surfactant assisted hydrothermal methods. The results show that with increasing of temperature, the crystallinity of nanoparticles is increased. In the presence of surfactants, the crystallinity of NiFe2O4 nanoparticles decreased in comparison with surfactant- free prepared samples. All of the nickel ferrite nanoparticles were superparamagnetic at room temperature.

/pdf/preparation-and-magnetic-properties-of-nano-size-nickel-upirsv60ut.pdf

Preparation and magnetic properties of nano size nickel ferrite particles using hydrothermal method.

Basics of Magnetism-Source of Magnetic Effect.- The Magnetization in Domains and Bulk Materials.- AC Properties of Ferrites.- Crystal Structure of Ferrites.- Chemical Aspects of Ferrites.- Microstructural Aspects of Ferrites.- Ferrite Processing.- Applications and Functions of Ferrites.- Ferrites for Permanent Magnet Applications.- Ferrite Inductors and Transformers for Low Power Applications.- Ferrites for EMI Suppression.- Ferrites for Entertainment Applications-Radio and TV.- Ferrite Transformers and Inductors at High Power.- Ferrites for Magnetic Recording.- Ferrites for Microwave Applications.- Miscellaneous Ferrite Application.- Physical, Mechanical and Thermal Aspects of Ferrites.- Magnetic Measurements on Ferrite Materials and Components.

/pdf/modern-ferrite-technology-4nsu3x4o9y.pdf

Modern Ferrite Technology

An x-ray Fresnel diffractive radiography platform was designed for use at the National Ignition Facility. It will enable measurements of micron-scale changes in the density gradients across an interface between isochorically heated warm dense matter materials, the evolution of which is driven primarily through thermal conductivity and mutual diffusion. We use 4.75 keV Ti K-shell x-ray emission to heat a 1000 μm diameter plastic cylinder, with a central 30 μm diameter channel filled with liquid D2, up to 8 eV. This leads to a cylindrical implosion of the liquid D2 column, compressing it to ∼2.3 g/cm3. After pressure equilibration, the location of the D2/plastic interface remains steady for several nanoseconds, which enables us to track density gradient changes across the material interface with high precision. For radiography, we use Cu He-α x rays at 8.3 keV. Using a slit aperture of only 1 μm width increases the spatial coherence of the source, giving rise to significant diffraction features in the radiography signal, in addition to the refraction enhancement, which further increases its sensitivity to density scale length changes at the D2/plastic interface.

Alex Goldman

Papers

Modern Ferrite Technology

Developing a platform for Fresnel diffractive radiography with 1 μm spatial resolution at the National Ignition Facility.