An implantable medical device, such as an implantable pulse generator (IPG) used with a spinal cord stimulation (SCS) system, includes a rechargeable lithiumion battery having an anode electrode with a substrate made substantially from titanium. Such battery construction allows the rechargeable battery to be discharged down to zero volts without damage to the battery. The implantable medical device includes battery charging and protection circuitry that controls the charging of the battery so as to assure its reliable and safe operation. A multi-rate charge algorithm is employed that minimizes charging time while ensuring the battery cell is safely charged. Fast charging occurs at safer lower battery voltages (e.g., battery voltage above about 2.5 V), and slower charging occurs when the battery nears full charge higher battery voltages (e.g., above about 4.0 V). When potentially less-than-safe very low voltages are encountered (e.g., less than 2.5 V), then very slow (trickle) charging occurs to bring the battery voltage back up to the safer voltage levels where more rapid charging can safely occur. The battery charging and protection circuitry also continuously monitors the battery voltage and current. If the battery operates outside of a predetermined range of voltage or current, the battery protection circuitry disconnects the battery from the particular fault, i.e. charging circuitry or load circuits.

Implantable Pulse Generators Using Rechargeable Zero-Volt Technology Lithium-Ion Batteries

A minimum Z height handheld electronic device and methods of assembly is described. The electronic device includes a single seamless housing having a front opening and a cover disposed within the front opening and attached to the seamless housing without a bezel.

Handheld computing device

Improved assemblies, systems, and methods provide an implantable pulse generator for prosthetic or therapeutic stimulation of muscles, nerves, or central nervous system tissue, or any combination. The implantable pulse generator is sized and configured to be implanted subcutaneously in a tissue region. The implantable pulse generator includes an electrically conductive laser welded titanium case. Control circuitry is located within the case, and includes a primary cell or rechargeable power source, a receive coil for receiving an RF magnetic field to recharge the rechargeable power source, and a microcontroller for control of the implantable pulse generator. Improved assemblies, systems, and methods also provide a stimulation system for prosthetic or therapeutic stimulation of muscles, nerves, or central nervous system tissue, or any combination. The stimulation system provides at least one electrically conductive surface, a lead connected to the electrically conductive surface, and an implantable pulse generator electrically connected to the lead.

Implantable pulse generator for providing functional and/or therapeutic stimulation of muscles and/or nerves and/or central nervous system tissue

A mechanism for transferring energy from an external power source to an implantable medical device is disclosed. A sensor may be used to measure a parameter that correlates to a temperature of the system that occurs during the transcutaneous coupling of energy. For example, the sensor may measure temperature of a surface of an antenna of the external power source. The measured parameter may then be compared to a programmable limit. A control circuit such as may be provided by the external power source may then control the temperature based on the comparison. The programmable limit may be, for example, under software control so that the temperature occurring during transcutaneous coupling of energy may be modified to fit then-current circumstances.

Inductively rechargeable external energy source, charger, system and method for a transcutaneous inductive charger for an implantable medical device

A lithium rechargeable battery in which an anti-rotation groove is integrally formed with a lower recess of a safety vent at a lower surface of a cap plate, and an insulating plate and a terminal plate rest in the anti-rotation groove so that the terminal plate is prevented from rotating when a cap assembly is assembled is provided In addition, instead of the anti-rotation groove, a resting recess is formed on a lower surface of the cap plate, and the insulating plate and the terminal plate rest in the resting recess, so that the terminal plate is prevented from rotating when the cap assembly is assembled

Lithium rechargeable battery

A method, device and system is disclosed for rapidly and safely discharging remaining energy stored in an electrochemical battery 104 in the event of an internal short circuit or other fault. In its best mode of implementation, if a sensor 116 detects one or more parameters such as battery temperature 204 or pressure 206, exceeding a predetermined threshold value 334, the terminals 144 of the battery or cell are intentionally short-circuited external to the battery through a low or near zero resistance load 150 which rapidly drains energy from the battery 104. Heat generated by such rapid drain is absorbed by a heat absorbing material 151 such as an endothermic phase-change material like paraffin. The rate energy is drained via the external discharge load 150 may be controlled with an electronic circuit 136 responsive to factors such as state of charge and battery temperature. Devices such as inductive charging coils 160, piezoelectric and Peltier devices 300, may also be used as emergency energy discharge loads. Heat absorption material 163 may be used to protect adjacent issue in medically-implanted devices.

Safety method, device and system for an energy storage device

The invention provides electrical storage battery assemblies and related methods for assembling such batteries. A battery assembly includes positive and negative electrode sheets and separator sheets sandwiched together and wrapped around a central mandrel to provide a spiral sandwich electrode assembly. The electrode assembly is housed inside a case that includes a case housing open at two ends and covers closing the two openings. The central mandrel of the electrode assembly is in electrical contact with one of the electrode sheets and a first battery terminal that passes through the case. A projecting member on the central mandrel provides the electrical connection between the electrode and the first battery terminal. The other electrode is in electrical contact with the case. A first insulator lies between the electrode assembly and the projecting member. A second insulator is positioned between the projecting member and the case.

Electrical battery assembly and method of manufacture

The invention includes a brazed ceramic ring that separates the positive and negative ends of the battery while still providing a leak-tight seal. The ceramic is aluminum oxide or zirconium oxide or zirconium oxide with 3% yttrium. The invention includes a brazing material that is greater than 50% gold. The invention includes a titanium alloy case (Ti-6Al-4V) which is titanium with 6% aluminum and 4% vanadium as its major alloying elements. The case has the desirable properties of titanium such as high strength for a relatively low weight; and the case has the requisite ability and electro-activity to be used as a positive current carrying element where the battery's positive electrode exhibits more than 3.5 V vs. Li/Li+.

Brazed ceramic seal for batteries with titanium-titanium-6A1-4V cases

A lithium ion battery particularly configured to be able to discharge to a very low voltage, e.g. zero volts, without causing permanent damage to the battery. More particularly, the battery is configured to define a Zero Volt Crossing Potential (ZCP) which is lower than a Damage Potential Threshold (DPT). A method for using a battery capable of tolerating discharge to zero volts is also disclosed.

Rechargeable lithium battery for tolerating discharge to zero volts

A lithium ion battery particularly configured to be able to discharge to a very low voltage, e.g. zero volts, without causing permanent damage to the battery. More particularly, the battery is configured to define a Zero Volt Crossing Potential (ZCP) which is lower than a Damage Potential Threshold (DPT).

Clay Kishiyama

Papers

Safety method, device and system for an energy storage device

Electrical battery assembly and method of manufacture

Brazed ceramic seal for batteries with titanium-titanium-6A1-4V cases

Rechargeable lithium battery for tolerating discharge to zero volts

Lithium ion battery capable of being discharged to zero volts