Preface. About the Authors. Acknowledgments. 1 Power Amplifier Fundamentals. 1.1 Introduction. 1.2 Definition of Power Amplifier Parameters. 1.3 Distortion Parameters. 1.4 Power Match Condition. 1.5 Class of Operation. 1.6 Overview of Semiconductors for PAs. 1.7 Devices for PA. 1.8 Appendix: Demonstration of Useful Relationships. 1.9 References. 2 Power Amplifier Design. 2.1 Introduction. 2.2 Design Flow. 2.3 Simplified Approaches. 2.4 The Tuned Load Amplifier. 2.5 Sample Design of a Tuned Load PA. 2.6 References. 3 Nonlinear Analysis for Power Amplifiers. 3.1 Introduction. 3.2 Linear vs. Nonlinear Circuits. 3.3 Time Domain Integration. 3.4 Example. 3.5 Solution by Series Expansion. 3.6 The Volterra Series. 3.7 The Fourier Series. 3.8 The Harmonic Balance. 3.9 Envelope Analysis. 3.10 Spectral Balance. 3.11 Large Signal Stability Issue. 3.12 References. 4 Load Pull. 4.1 Introduction. 4.2 Passive Source/Load Pull Measurement Systems. 4.3 Active Source/Load Pull Measurement Systems. 4.4 Measurement Test-sets. 4.5 Advanced Load Pull Measurements. 4.6 Source/Load Pull Characterization. 4.7 Determination of Optimum Load Condition. 4.8 Appendix: Construction of Simplified Load Pull Contours through Linear Simulations. 4.9 References. 5 High Efficiency PA Design Theory. 5.1 Introduction. 5.2 Power Balance in a PA. 5.3 Ideal Approaches. 5.4 High Frequency Harmonic Tuning Approaches. 5.5 High Frequency Third Harmonic Tuned (Class F). 5.6 High Frequency Second Harmonic Tuned. 5.7 High Frequency Second and Third Harmonic Tuned. 5.8 Design by Harmonic Tuning. 5.9 Final Remarks. 5.10 References. 6 Switched Amplifiers. 6.1 Introduction. 6.2 The Ideal Class E Amplifier. 6.3 Class E Behavioural Analysis. 6.4 Low Frequency Class E Amplifier Design. 6.5 Class E Amplifier Design with 50# Duty-cycle. 6.6 Examples of High Frequency Class E Amplifiers. 6.7 Class E vs. Harmonic Tuned. 6.8 Class E Final Remarks. 6.9 Appendix: Demonstration of Useful Relationships. 6.10 References. 7 High Frequency Class F Power Amplifiers. 7.1 Introduction. 7.2 Class F Description Based on Voltage Wave-shaping. 7.3 High Frequency Class F Amplifiers. 7.4 Bias Level Selection. 7.5 Class F Output Matching Network Design. 7.6 Class F Design Examples. 7.7 References. 8 High Frequency Harmonic Tuned Power Amplifiers. 8.1 Introduction. 8.2 Theory of Harmonic Tuned PA Design. 8.3 Input Device Nonlinear Phenomena: Theoretical Analysis. 8.4 Input Device Nonlinear Phenomena: Experimental Results. 8.5 Output Device Nonlinear Phenomena. 8.6 Design of a Second HT Power Amplifier. 8.7 Design of a Second and Third HT Power Amplifier. 8.8 Example of 2nd HT GaN PA. 8.9 Final Remarks. 8.10 References. 9 High Linearity in Efficient Power Amplifiers. 9.1 Introduction. 9.2 Systems Classification. 9.3 Linearity Issue. 9.4 Bias Point Influence on IMD. 9.5 Harmonic Loading Effects on IMD. 9.6 Appendix: Volterra Analysis Example. 9.7 References. 10 Power Combining. 10.1 Introduction. 10.2 Device Scaling Properties. 10.3 Power Budget. 10.4 Power Combiner Classification. 10.5 The T-junction Power Divider. 10.6 Wilkinson Combiner. 10.7 The Quadrature (90 ) Hybrid. 10.8 The 180 Hybrid (Ring Coupler or Rat-race). 10.9 Bus-bar Combiner. 10.10 Other Planar Combiners. 10.11 Corporate Combiners. 10.12 Resonating Planar Combiners. 10.13 Graceful Degradation. 10.14 Matching Properties of Combined PAs. 10.15 Unbalance Issue in Hybrid Combiners. 10.16 Appendix: Basic Properties of Three-port Networks. 10.17 References. 11 The Doherty Power Amplifier. 11.1 Introduction. 11.2 Doherty's Idea. 11.3 The Classical Doherty Configuration. 11.4 The 'AB-C' Doherty Amplifier Analysis. 11.5 Power Splitter Sizing. 11.6 Evaluation of the Gain in a Doherty Amplifier. 11.7 Design Example. 11.8 Advanced Solutions. 11.9 References. Index.

/pdf/high-efficiency-rf-and-microwave-solid-state-power-4xdx1261hq.pdf

High Efficiency RF and Microwave Solid State Power Amplifiers

A facile technique based on pulsed power test has been developed to characterize W-band MMIC power amplifiers and optimize their gain and PAE (power added efficiency) on-wafer. By suppressing thermal effects usually associated with conventional on-wafer tests, the pulsed power technique makes it possible to not only establish device binning criteria but also eliminate in-module bias tuning. It thus provides significant cost savings in volume production environments.

Characterization of W-band MMIC power amplifier using on-wafer pulsed power test

Chapter 4. Load Pull

A novel technique has been developed to optimize the power MMIC performance by using on-wafer pulsed power test. Traditionally, only dc parameters were used to determine the chip operating bias condition. The on-wafer test was used to determine the functionality of the device, and the MMIC chip performance is optimized through manual bias tuning at module level. This technique provides significant cost savings in high volume production environment.

D.C. Yang

Papers

Performance Optimization of Ka-Band MMIC Power Amplifier Using On-Wafer Pulsed Power Test