Quantitative and reproducible air-coupled ultrasound (ACU) testing requires characterization of the volumetric pressure fields radiated by ACU probes. In this paper, a closed-form reradiation method combining the Rayleigh–Sommerfeld integral and time-reversal acoustics is proposed, which allows calculation of both near- field and far-field based on a single-plane measurement. The method was validated for both 3-D (circular, square) and 2-D (rectangular) planar transducers in the 50–230 kHz range. The pressure fields were scanned with a calibrated microphone. The measurement window was at least four times the size of the transducer area and the grid step size was one third of the wavelength. Best results were observed by acquiring the measurement plane at near-field distance. The method accurately reproduces pulsed ultrasound waveforms and pressure distributions (RMSE <2.5% in far field and <5.5% in near field), even at the transducer radiation surface. The effects of speed of sound drifts during the scan in the pressure were negligible (RMSE <0.3%). The reradiation method clearly outperforms conventional baffled piston models. Possible applications are transducer manufacture control (imperfections at radiation surface) and calibration (on-axis pressure, side lobes, and beamwidth) together with generation of accurate source functions for quantitative nondestructive evaluation inverse problems.

/pdf/calculation-of-volumetric-sound-field-of-pulsed-air-coupled-3km01fkimz.pdf

Calculation of Volumetric Sound Field of Pulsed Air-Coupled Ultrasound Transducers Based on Single-Plane Measurements

Computational and experimental investigation of the fields generated by a 1-3 piezocomposite transducer.

Ultrasonic needle hydrophone calibration in air by a parabolic off-axis mirror focused beam using three-transducer reciprocity.

Miniature microphones suitable for measurements of ultrasonic wave field scans in air are expensive or lack sensitivity or do not cover the range beyond 100 kHz. It is essential that they are too large for such fields measurements. The use of a ferroelectret (FE) film is proposed to construct a miniature, needle-style 0.5-mm-diameter sensitive element ultrasonic microphone. FE has an acoustic impedance much closer to that of air compared with other alternatives and is low cost and easy to process. The performance of the microphone was evaluated by measuring the sensitivity area map, directivity, ac response, and calibrating the absolute sensitivity. Another novel contribution here is that the sensitivity map was obtained by scanning the focused beam of a laser diode over the microphone surface, producing thermoelastic ultrasound excitation. The electroacoustic response of the microphone served as a sensitivity indicator at a scan spot. Micrometer scale granularity of the FE sensitivity was revealed in the sensitivity map images. It was also demonstrated that the relative ac response of the microphone can be obtained using pulsed laser beam thermoelastic excitation of the whole microphone surface with a laser diode. The absolute sensitivity calibration was done using the hybrid three-transducer reciprocity technique. A large aperture, air coupled transducer beam was focused onto the microphone surface, using the parabolic off-axis mirror. This measurement validated the laser ac response measurements. The FE microphone performance was compared with biaxially stretched polyvinylidene difluoride (PVDF) microphone of the same construction.

https://ieeexplore.ieee.org/ielx7/58/7307696/09940307.pdf

Miniature Ferroelectret Microphone Design and Performance Evaluation Using Laser Excitation

Miniature microphones suitable for measurements of ultrasonic wave field scans in air are expensive or lack sensitivity or do not cover the range beyond 100 kHz. It is essential that they are too large for such fields measurements. The use of a ferroelectret (FE) film is proposed to construct a miniature, needle-style 0.5-mm-diameter sensitive element ultrasonic microphone. FE has an acoustic impedance much closer to that of air compared with other alternatives and is low cost and easy to process. The performance of the microphone was evaluated by measuring the sensitivity area map, directivity, ac response, and calibrating the absolute sensitivity. Another novel contribution here is that the sensitivity map was obtained by scanning the focused beam of a laser diode over the microphone surface, producing thermoelastic ultrasound excitation. The electroacoustic response of the microphone served as a sensitivity indicator at a scan spot. Micrometer scale granularity of the FE sensitivity was revealed in the sensitivity map images. It was also demonstrated that the relative ac response of the microphone can be obtained using pulsed laser beam thermoelastic excitation of the whole microphone surface with a laser diode. The absolute sensitivity calibration was done using the hybrid three-transducer reciprocity technique. A large aperture, air coupled transducer beam was focused onto the microphone surface, using the parabolic off-axis mirror. This measurement validated the laser ac response measurements. The FE microphone performance was compared with biaxially stretched polyvinylidene difluoride (PVDF) microphone of the same construction. 

This paper describes a technique for predicting and measuring acoustic radiation from ultrasonic transducers operating into air in continuous wave mode over the frequency range 50 kHz to 2 MHz. Using surface displacement data for the radiating aperture, the transmitted pressure field is computed. The field calculation includes simulation of propagation channel attenuation and, where required for comparison with experimentally measured fields, the directional response of the hydrophone. Surface displacement data may be obtained directly from laser interferometric measurement of the excited aperture, or indirectly from finite element analysis of the transmitter. To provide validation by experimental measurement of transducer beam profiles, an environmentally controlled, draught-proof scanning system was utilised. Comparison of experimental and simulated results for different transducer technologies proposed for use in air has been performed. Results indicate good agreement between experiment and theory and a selection of these results is presented in this paper. Where appropriate, comparisons are also made with fields predicted from classical aperture diffraction theory and significant differences are highlighted and explained.

G. Hayward

Papers

Beam profile measurements and simulations for air-coupled ultrasonic transducers