The mechanical properties of skin are important for a number of applications including surgery, dermatology, impact biomechanics and forensic science. In this study, we have investigated the influence of location and orientation on the deformation characteristics of 56 samples of excised human skin. Uniaxial tensile tests were carried out at a strain rate of 0.012 s(-1) on skin from the back. Digital Image Correlation was used for 2D strain measurement and a histological examination of the dermis was also performed. The mean ultimate tensile strength (UTS) was 21.6±8.4 MPa, the mean failure strain 54%±17%, the mean initial slope 1.18±0.88 MPa, the mean elastic modulus 83.3±34.9 MPa and the mean strain energy was 3.6±1.6 MJ/m(3). A multivariate analysis of variance has shown that these mechanical properties of skin are dependent upon the orientation of the Langer lines (P<0.0001-P=0.046). The location of specimens on the back was also found to have a significant effect on the UTS (P=0.0002), the elastic modulus (P=0.001) and the strain energy (P=0.0052). The histological investigation concluded that there is a definite correlation between the orientation of the Langer lines and the preferred orientation of collagen fibres in the dermis (P<0.001). The data obtained in this study will provide essential information for those wishing to model the skin using a structural constitutive model.

https://researchrepository.ucd.ie/bitstream/10197/4616/2/Repos%20-%20not-%20commented2%20done.pdf

Characterization of the anisotropic mechanical properties of excised human skin

The mechanical properties of the skin are important for various applications. Numerous tests have been conducted to characterize the mechanical behavior of this tissue, and this article presents a review on different experimental methods used. A discussion on the general mechanical behavior of the skin, including nonlinearity, viscoelasticity, anisotropy, loading history dependency, failure properties, and aging effects, is presented. Finally, commonly used constitutive models for simulating the mechanical response of skin are discussed in the context of representing the empirically observed behavior.

Skin mechanical properties and modeling: A review.

Tendons are exposed to complex loading scenarios that can only be quantified by mathematical models, requiring a full knowledge of tendon mechanical properties. This study measured the anisotropic, nonlinear, elastic material properties of tendon. Previous studies have primarily used constant strain-rate tensile tests to determine elastic modulus in the fiber direction. Data for Poisson's ratio aligned with the fiber direction and all material properties transverse to the fiber direction are sparse. Additionally, it is not known whether quasi-static constant strain-rate tests represent equilibrium elastic tissue behavior. Incremental stress-relaxation and constant strain-rate tensile tests were performed on sheep flexor tendon samples aligned with the tendon fiber direction or transverse to the fiber direction to determine the anisotropic properties of toe-region modulus (E0), linear-region modulus (E), and Poisson's ratio (v). Among the modulus values calculated, only fiber-aligned linear-region modulus (E1) was found to be strain-rate dependent. The E1 calculated from the constant strain-rate tests were significantly greater than the value calculated from incremental stress-relaxation testing. Fiber-aligned toe-region modulus (E(1)0 = 10.5 +/- 4.7 MPa) and linear-region modulus (E1 = 34.0 +/- 15.5 MPa) were consistently 2 orders of magnitude greater than transverse moduli (E(2)0 = 0.055 +/- 0.044 MPa, E2 = 0.157 +/- 0.154 MPa). Poisson's ratio values were not found to be rate-dependent in either the fiber-aligned (v12 = 2.98 +/- 2.59, n = 24) or transverse (v21 = 0.488 +/- 0.653, n = 22) directions, and average Poisson's ratio values in the fiber-aligned direction were six times greater than in the transverse direction. The lack of strain-rate dependence of transverse properties demonstrates that slow constant strain-rate tests represent elastic properties in the transverse direction. However, the strain-rate dependence demonstrated by the fiber-aligned linear-region modulus suggests that incremental stress-relaxation tests are necessary to determine the equilibrium elastic properties of tendon, and may be more appropriate for determining the properties to be used in elastic mathematical models.

Effect of Fiber Orientation and Strain Rate on the Nonlinear Uniaxial Tensile Material Properties of Tendon

Tendons have complex mechanical behaviors that are viscoelastic, nonlinear, and anisotropic. It is widely held that these behaviors are provided for by the tissue's composition and structure. However, little data are available to quantify such structure-function relationships. This study quantified tendon mechanical behaviors, including viscoelasticity and nonlinearity, for groups of mice that were genetically engineered for altered extracellular matrix proteins. Uniaxial tensile stress-relaxation experiments were performed on tail tendon fascicles from the following groups: eight week old decorin knockout, eight week old reduced type I collagen, three week old control, and eight week old control. Data were fit using Fung's quasilinear viscoelastic model, where the model parameters represent the linear viscoelastic and nonlinear elastic response. The viscoelastic properties demonstrated a larger and faster stress relaxation for the decorin knockout and a smaller and slower stress relaxation for the three week control. The elastic parameter, A, in the eight week control group was significantly greater than in the collagen reduction and three week control groups. This study provides quantitative evidence for structure-function relationships in tendon, including the role of proteoglycan in viscoelasticity. Future studies should directly correlate composition and structure with tendon mechanics for the design and evaluation of tissue-engineered constructs or tendon repairs.

Effect of altered matrix proteins on quasilinear viscoelastic properties in transgenic mouse tail tendons.

The mechanical characteristics of skin are extremely complex and have not been satisfactorily simulated by conventional engineering models. The ability to predict human skin behaviour and to evaluate changes in the mechanical properties of the tissue would inform engineering design and would prove valuable in a diversity of disciplines, for example the pharmaceutical and cosmetic industries, which currently rely upon experiments performed in animal models. The aim of this study was to develop a predictive anisotropic, hyperelastic constitutive model of human skin and to validate this model using laboratory data. As a corollary, the mechanical characteristics of human and murine skin have been compared. A novel experimental design, using tensile tests on circular skin specimens, and an optimisation procedure were adopted for laboratory experiments to identify the material parameters of the tissue. Uniaxial tensile tests were performed along three load axes on excised murine and human skin samples, using a single set of material parameters for each skin sample. A finite element model was developed using the transversely isotropic, hyperelastic constitutive model of Weiss et al. (1996) and was embedded within a Veronda–Westmann isotropic material matrix, using three fibre families to create anisotropic behaviour. The model was able to represent the nonlinear, anisotropic behaviour of the skin well. Additionally, examination of the optimal material coefficients and the experimental data permitted quantification of the mechanical differences between human and murine skin. Differences between the skin types, most notably the extension of the skin at low load, have highlighted some of the limitations of murine skin as a biomechanical model of the human tissue.

The development of accurate, predictive computational models of human tissue, such as skin, to reduce, refine or replace animal models and to inform developments in the medical, engineering and cosmetic fields, is a significant challenge but is highly desirable. Concurrent advances in computer technology and our understanding of human physiology must be utilised to produce more accurate and accessible predictive models, such as the finite element model described in this study.

An anisotropic, hyperelastic model for skin: experimental measurements, finite element modelling and identification of parameters for human and murine skin.

The mechanical response of rat dorsal skin was experimentally studied under cyclic uniaxial ramp stretches to various strain levels. Special emphasis was paid to the effects of the preconditioning protocol on the stress-strain relationship, and to the effects of ramp strain level and proteoglycan (PG) depletion, on viscoelasticity and preconditioning responses. The results show that preconditioning significantly reduced both the slope of the low strain stress-strain relationship, and the stress levels at consecutive stretch cycles. Following a short rest there was a significant partial recovery. Stress decay due to preconditioning was significant at all strain levels, and increased with strain. Stress relaxation was significant at all strain levels, but varied little with strain. Recovery following a 10 min rest was minor at all strain levels and varied little with strain. PG-depleted samples manifested similar response patterns. These results are consistent with the following notion: (1) skin consists of three mechanical components: elastin and proteoglycan which dominate the low strain response and are effected by preconditioning and (PG) depletion, and collagen which dominates the high strain response and is unaffected by preconditioning and PG depletion; (2) that the viscoelasticity of elastin and PG vs that of collagen are similar, so that rat dorsal skin can be regarded quasilinear viscoelastic.

H Eshel

Papers

Effects of Strain Level and Proteoglycan Depletion on Preconditioning and Viscoelastic Responses of Rat Dorsal Skin