In recent years, the power conversion efficiency of perovskite solar cells has increased to reach over 20%. Finding an effective means of defect passivation is thought to be a promising route for bringing further increases in the power conversion efficiency and the open-circuit voltage (VOC) of perovskite solar cells. Here, we report the use of an organic halide salt phenethylammonium iodide (PEAI) on HC(NH2)2–CH3NH3 mixed perovskite films for surface defect passivation. We find that PEAI can form on the perovskite surface and results in higher-efficiency cells by reducing the defects and suppressing non-radiative recombination. As a result, planar perovskite solar cells with a certificated efficiency of 23.32% (quasi-steady state) are obtained. In addition, a VOC as high as 1.18 V is achieved at the absorption threshold of 1.53 eV, which is 94.4% of the Shockley–Queisser limit VOC (1.25 V). Planar perovskite solar cells that have been passivated using the organic halide salt phenethylammonium iodide are shown to have suppressed non-radiative recombination and operate with a certified power conversion efficiency of 23.3%.

Surface passivation of perovskite film for efficient solar cells

Three-dimensional organic-inorganic perovskites have emerged as one of the most promising thin-film solar cell materials owing to their remarkable photophysical properties, which have led to power conversion efficiencies exceeding 20 per cent, with the prospect of further improvements towards the Shockley-Queisser limit for a single‐junction solar cell (33.5 per cent). Besides efficiency, another critical factor for photovoltaics and other optoelectronic applications is environmental stability and photostability under operating conditions. In contrast to their three-dimensional counterparts, Ruddlesden-Popper phases--layered two-dimensional perovskite films--have shown promising stability, but poor efficiency at only 4.73 per cent. This relatively poor efficiency is attributed to the inhibition of out-of-plane charge transport by the organic cations, which act like insulating spacing layers between the conducting inorganic slabs. Here we overcome this issue in layered perovskites by producing thin films of near-single-crystalline quality, in which the crystallographic planes of the inorganic perovskite component have a strongly preferential out-of-plane alignment with respect to the contacts in planar solar cells to facilitate efficient charge transport. We report a photovoltaic efficiency of 12.52 per cent with no hysteresis, and the devices exhibit greatly improved stability in comparison to their three-dimensional counterparts when subjected to light, humidity and heat stress tests. Unencapsulated two-dimensional perovskite devices retain over 60 per cent of their efficiency for over 2,250 hours under constant, standard (AM1.5G) illumination, and exhibit greater tolerance to 65 per cent relative humidity than do three-dimensional equivalents. When the devices are encapsulated, the layered devices do not show any degradation under constant AM1.5G illumination or humidity. We anticipate that these results will lead to the growth of single-crystalline, solution-processed, layered, hybrid, perovskite thin films, which are essential for high-performance opto-electronic devices with technologically relevant long-term stability.

High-efficiency two-dimensional Ruddlesden–Popper perovskite solar cells

Planar perovskite solar cells (PSCs) made entirely via solution processing at low temperatures (<150°C) offer promise for simple manufacturing, compatibility with flexible substrates, and perovskite-based tandem devices. However, these PSCs require an electron-selective layer that performs well with similar processing. We report a contact-passivation strategy using chlorine-capped TiO2 colloidal nanocrystal film that mitigates interfacial recombination and improves interface binding in low-temperature planar solar cells. We fabricated solar cells with certified efficiencies of 20.1 and 19.5% for active areas of 0.049 and 1.1 square centimeters, respectively, achieved via low-temperature solution processing. Solar cells with efficiency greater than 20% retained 90% (97% after dark recovery) of their initial performance after 500 hours of continuous room-temperature operation at their maximum power point under 1-sun illumination (where 1 sun is defined as the standard illumination at AM1.5, or 1 kilowatt/square meter).

https://science.sciencemag.org/content/sci/early/2017/02/01/science.aai9081.full.pdf

Efficient and stable solution-processed planar perovskite solar cells via contact passivation.

The photovoltaics of organic–inorganic lead halide perovskite materials have shown rapid improvements in solar cell performance, surpassing the top efficiency of semiconductor compounds such as CdTe and CIGS (copper indium gallium selenide) used in solar cells in just about a decade. Perovskite preparation via simple and inexpensive solution processes demonstrates the immense potential of this thin-film solar cell technology to become a low-cost alternative to the presently commercially available photovoltaic technologies. Significant developments in almost all aspects of perovskite solar cells and discoveries of some fascinating properties of such hybrid perovskites have been made recently. This Review describes the fundamentals, recent research progress, present status, and our views on future prospects of perovskite-based photovoltaics, with discussions focused on strategies to improve both intrinsic and extrinsic (environmental) stabilities of high-efficiency devices. Strategies and challenges regardi...

Halide Perovskite Photovoltaics: Background, Status, and Future Prospects

The ionic defects at the surfaces and grain boundaries of organic–inorganic halide perovskite films are detrimental to both the efficiency and stability of perovskite solar cells. Here, we show that quaternary ammonium halides can effectively passivate ionic defects in several different types of hybrid perovskite with their negative- and positive-charged components. The efficient defect passivation reduces the charge trap density and elongates the carrier recombination lifetime, which is supported by density-function-theory calculation. The defect passivation reduces the open-circuit-voltage deficit of the p–i–n-structured device to 0.39 V, and boosts the efficiency to a certified value of 20.59 ± 0.45%. Moreover, the defect healing also significantly enhances the stability of films in ambient conditions. Our findings provide an avenue for defect passivation to further improve both the efficiency and stability of solar cells. Losses in solar cells can be caused by material defects in the bulk or at interfaces. Here, Zheng et al. use quaternary ammonium halides to passivate various perovskite absorbers and prepare solar cells with certified efficiency above 20%, suggesting that both anionic and cation defects are affected.

https://par.nsf.gov/servlets/purl/10056130

Defect passivation in hybrid perovskite solar cells using quaternary ammonium halide anions and cations

Herein, we report an extended-gate-type organic field-effect transistor (OFET) sensor for oxytocin. The fabricated OFET-based immunosensor has successfully detected oxytocin at a ppt level in human saliva with high recovery rates (96-102%). We believe our sensor would pave the way for the realization of portable sensors for healthcare monitoring.

Oxytocin detection at ppt level in human saliva by an extended-gate-type organic field-effect transistor.

This study aims to evaluate the indoor thermal environment within a detached residence in summer by applying combined convection and radiation air conditioning system using the refrigerant gas of room air conditioners (RACs). First, field measurements were performed in a detached residence at Hiroshima, Japan, in July and August 2021. Consequently, PMV values were generally maintained within the comfortable range during air-conditioning operation. The amount of heat generated by convection (via the RAC indoor unit) Qc and that by radiation (via the radiation panel) Qr were determined as 426 and 259 W, respectively, and the overall heat generated Qtotal was determined as 685 W. Applying the CFD model, thermal environment was compared varying the ratio between Qc and Qr with a constant Qtotal of 685 W. Results showed that the synergistic operation of a RAC and a radiant panel presented more comfortable PMV values than that of a single RAC application. Furthermore, the airflow from the RAC decreased with an increase in Qr ratio, and the chilled radiant panel provided a cooling effect around the dining area, where the airflow of the RAC was inadequate, thereby improving the thermal comfort.

/pdf/improved-thermal-performance-of-combined-convection-and-15k5cdy6.pdf

Hirokazu Nagaoka

Papers

Oxytocin detection at ppt level in human saliva by an extended-gate-type organic field-effect transistor.

Improved Thermal Performance of Combined Convection and Radiation Using Room Air Conditioner