A method is presented for interim use in assessing the noise generated by fans and compressors in turbojet and turbofan engines. One-third octave band sound pressure levels consisting of broadband, discrete tone, and combination-tone noise components are predicted. Spectral distributions and directivity variations are specified. The method is based on that developed by other investigators with modifications derived from an analysis of full-scale, single-stage fan data. Comparisons of predicted and measured noise performance are presented, and requirements for improving the method are discussed.

/pdf/interim-prediction-method-for-fan-and-compressor-source-1r7p1hbxhh.pdf

Interim prediction method for fan and compressor source noise

Rotor tip-clearance induced noise, both in the form of rotor self noise and rotor-stator interaction noise, constitutes a significant component of total fan noise. Innovative yet cost effective techniques to suppress rotor-generated noise are, therefore, of foremost importance for improving the noise signature of turbofan engines. To that end, the feasibility of a passive porous treatment strategy to positively modify the tip-clearance flow field is addressed. The present study is focused on accurate viscous flow calculations of the baseline and the treated rotor flow fields. Detailed comparison between the computed baseline solution and experimental measurements shows excellent agreement. Tip-vortex structure, trajectory, strength, and other relevant aerodynamic quantities are extracted from the computed database. Extensive comparison between the untreated and treated tip-clearance flow fields is performed. The effectiveness of the porous treatment for altering the rotor-tip vortex flow field in general and reducing the intensity of the tip vortex, in particular, is demonstrated. In addition, the simulated flow field for the treated tip clearly shows that substantial reduction in the intensity of both the shear layer roll-up and boundary layer separation on the wall is achieved.

/pdf/a-novel-approach-for-reducing-rotor-tip-clearance-induced-3f918jz3dk.pdf

A Novel Approach for Reducing Rotor Tip-Clearance Induced Noise in Turbofan Engines

The role of the interaction of rotor tip flow irregularities (vortices and velocity defects) with downstream stator vanes is discussed as a possible fan noise mechanism. This is accomplished by: (1) indicating some of the mothods of formation of these flow irregularities; (2) observing how they would behave with respect to known noise behavior; and (3) attempting to compare the strength of the rotor tip flow irregularity mechanism with the strength of the more common rotor wake-stator mechanism. The rotor tip flow irregularity-stator interaction is indicated as being a probable inflight noise source.

/pdf/interaction-of-rotor-tip-flow-irregularities-with-stator-3spqhd9wdm.pdf

Interaction of rotor tip flow irregularities with stator vanes as a noise source

A liner design for noise suppressors with outer wall treatment such as in an engine inlet is presented which potentially circumvents the problems of resolution in modal measurement. The method is based on the fact that the modal optimum impedance and the maximum possible sound power attenuation at this optimum can be expressed as functions of cutoff ratio alone. Modes with similar cutoff ratios propagate similarly in the duct and in addition propagate similarly to the far field. Thus there is no need to determine the acoustic power carried by these modes individually, and they can be grouped together as one entity. With the optimum impedance and maximum attenuation specified as functions of cutoff ratio, the off-optimum liner performance can be estimated using an approximate attenuation equation.

/pdf/inlet-noise-suppressor-design-method-based-upon-the-3nbqdnylx6.pdf

Inlet noise suppressor design method based upon the distribution of acoustic power with mode cutoff ratio

Model and full scale test results relating to fan noise in-flight effects

Flyover and static noise data from several engines are presented that show inlet fan noise measured in flight can be lower than that projected from static tests for some engines. The differences between flight and static measurements appear greatest when the fan fundamental tone due to rotor-stator interaction or to the rotor-alone field is below cutoff. Data from engine and fan tests involving inlet treatment on the walls only are presented that show the attenuation from this treatment is substantially larger than expected from previous theories or flow duct experience. Data showing noise shielding effects due to the location of the engine on the airplane are also presented. These observations suggest that multiringed inlets may not be necessary to achieve the desired noise reduction in many applications.

/pdf/effects-of-forward-velocity-and-acoustic-treatment-on-inlet-13u65fm46o.pdf

J. E. Merriman

Papers

Effects of forward velocity and acoustic treatment on inlet fan noise