The talk with present the key results of the IPCC Working Group III 5th assessment report. Concluding four years of intense scientific collaboration by hundreds of authors from around the world, the report responds to the request of the world's governments for a comprehensive, objective and policy neutral assessment of the current scientific knowledge on mitigating climate change. The report has been extensively reviewed by experts and governments to ensure quality and comprehensiveness.

Climate change 2014 - Mitigation of climate change

Over the last decades, research efforts have been made at developing more effective technologies for the remediation of waters containing persistent organic pollutants. Among the various technologies, the so-called electrochemical advanced oxidation processes (EAOPs) have caused increasing interest. These technologies are based on the electrochemical generation of strong oxidants such as hydroxyl radicals ( OH). Here, we present an exhaustive review on the treatment of various synthetic and real wastewaters by five key EAOPs, i.e., anodic oxidation (AO), anodic oxidation with electrogenerated H 2 O 2 (AO-H 2 O 2 ), electro-Fenton (EF), photoelectro-Fenton (PEF) and solar photoelectro-Fenton (SPEF), alone and in combination with other methods like biological treatment, electrocoagulation, coagulation and membrane filtration processes. Fundamentals of each EAOP are also given.

Electrochemical advanced oxidation processes: A review on their application to synthetic and real wastewaters

Mesoporous semiconducting films consisting of preferentially orientated monoclinic-phase nanocrystals of tungsten trioxide have been prepared using a novel version of the sol−gel method. Transformations undergone by a colloidal solution of tungstic acid, stabilized by an organic additive such as poly(ethylene glycol) (PEG) 300, as a function of the annealing temperature have been followed by means of a confocal Raman microscope. The shape and size of WO3 nanoparticles, the porosity, and the properties of the films depend critically on preparation parameters, such as the tungstic acid/PEG ratio, the PEG chain length, and the annealing conditions. Well-crystallized WO3 films combine excellent photoresponse to the blue region of the solar spectrum, up to 500 nm, with good transparency at wavelengths larger than 550 nm. Particular applications of these nanocrystalline WO3 films include photoelectrochemical and electrochromic devices.

Crystallographically oriented mesoporous WO3 films: synthesis, characterization, and applications.

Chemical characterization of particulate emissions from diesel engines: A review

We review the state of the art in using passive sampling technology for environmental monitoring of waterborne organic and inorganic pollutants. We discuss strategies for sampler design, calibration, in situ sampling and quality-control issues, and advantages and challenges associated with passive sampling in aqueous environments. We then review typical applications of passive samplers in assessing the aquatic environment.

Passive sampling techniques for monitoring pollutants in water

A new, rapid air sampling/sample preparation methodology was investigated using adsorptive solid-phase microextraction (SPME) fiber coatings and nonequilibrium conditions for volatile organic compounds (VOCs). This method is the fastest extraction technique for air sampling at typical airborne VOC concentrations. A theoretical model for the extraction was formulated based on the diffusion through the interface between the sampled (bulk) air and the SPME coating. Parameters that affect the extraction process including sampling time, air velocity, air temperature, and relative humidity were investigated with the porous (solid) PDMS/DVB and Carboxen/PDMS coatings. Very short sampling times from 5 s to 1 min were used to minimize the effects of competitive adsorption and to calibrate the extraction process in the initial linear extraction region. The predicted amounts of extracted mass compared well with the measured amounts of target VOCs. Findings presented in this study extend the existing fundamental know...

Air sampling with porous solid-phase microextraction fibers

A needle trap device (NTD) and commercial poly(dimethylsiloxane) (PDMS) 7-μm film thickness solid-phase microextraction (SPME) fibers were used for the sampling and analysis of aerosols and airborne particulate matter (PM) from an inhaler-administered drug, spray insect repellant, and tailpipe diesel exhaust. The NTD consisted of a 0.53-mm o.d. stainless steel needle having 5 mm of quartz wool packing section near the needle tip. Samples were collected by drawing air across the NTD with a Luer-tip syringe or via direct exposure of the SPME fiber. The mass loading of PM was varied by adjusting the volume of air pulled through the NTD or by varying the sampling time for the SPME fiber. The air volumes ranged from 0.1 to 50 mL, and sampling times varied from 10 s to 16 min. Particulates were either trapped on the needle packing or sorbed onto the SPME fiber. The devices were introduced to a chromatograph/mass spectrometer (GC/MS) injector for 5 min desorption. In the case of the NTD, 10 μL of clean air was d...

/pdf/sampling-and-analysis-of-airborne-particulate-matter-and-2mjwvzubce.pdf

Sampling and analysis of airborne particulate matter and aerosols using in-needle trap and SPME fiber devices.

https://works.bepress.com/jacek_koziel/159/download/

Field air analysis with SPME device

A new sampling and analysis method for formaldehyde in indoor air was tested in several indoor air surveys. The method was based on the use of solid-phase microextraction (SPME) poly(dimethylsiloxane)/divinylbenzene,65-μm fiber and gas chromatography. Indoor air surveys included grab and time-weighted average (TWA) sampling and were completed at six locations using (a) the SPME method employing on-fiber formaldehyde derivatization with o-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine hydrochloride and (b) the conventional National Institute for Occupational Safety and Health (NIOSH) 2451 method. Sampling time for SPME fiber ranged from 10 min for grab sampling to 8 h for TWA sampling. Sampling locations included a residential house, a rental apartment, an office building, and industrial workplaces. The air concentrations measured by SPME ranged from 10 to 380 ppbv and correlated well with those estimated by the NIOSH method. Results also indicated that in some cases the formaldehyde concentrations measured in...

/pdf/field-sampling-and-determination-of-formaldehyde-in-indoor-3eeizwgw6g.pdf

Field sampling and determination of formaldehyde in indoor air with solid-phase microextraction and on-fiber derivatization.

https://lib.dr.iastate.edu/cgi/viewcontent.cgi?article=2212&context=abe_eng_pubs

Characterization of volatile organic compounds and odorants associated with swine barn particulate matter using solid-phase microextraction and gas chromatography-mass spectrometry-olfactometry.

Jacek A. Koziel

Papers

Air sampling with porous solid-phase microextraction fibers

Sampling and analysis of airborne particulate matter and aerosols using in-needle trap and SPME fiber devices.

Field air analysis with SPME device

Field sampling and determination of formaldehyde in indoor air with solid-phase microextraction and on-fiber derivatization.

Characterization of volatile organic compounds and odorants associated with swine barn particulate matter using solid-phase microextraction and gas chromatography-mass spectrometry-olfactometry.