Comparison of ATH and SiO2 fillers filled silicone rubber composites for HTV insulators

How to effectively improve the tracking and erosion resistance of silicone rubber (SR) was an urgent topic in the field of high-voltage insulation. In this work, the tracking and erosion resistance of SR was significantly improved by incorporating platinum (Pt) catalyst and nitrogen-containing silane (NS). The suppression effect and mechanism of Pt/NS on tracking and erosion were studied by inclined plane (IP) test, thermogravimetry (TG), thermogravimetry-Fourier transform infrared spectrometry, laser Raman spectroscopy, and scanning electron microscopy. It revealed that when 1.4 phr of NS and 6.7 ppm of Pt were added, the tracking resistance of SR was improved from 2.5 to 4.5 kV level in the IP test, and the eroded mass was significantly reduced. This might be attributed to the synergistic effect of Pt/NS on silicone chains. At a high temperature produced by arc discharge, Pt/NS would catalyze radical cross-linking, meanwhile suppressing oxidation and depolymerization of silicone chains. Hence, a tightly...

Suppression Effect and Mechanism of Platinum and Nitrogen-Containing Silane on the Tracking and Erosion of Silicone Rubber for High-Voltage Insulation.

This study presents two different methods under uniform and non-uniform pollution layer in order to measure and calculate the leakage current (LC) of silicone rubber insulators. Experimental test for evaluating the LC analysis of polluted insulator have been done in a laboratory clean fog chamber. The electric field and potential distributions were obtained from finite element method software for 3D models. The mathematical background and circuit theory are described in details by a section of insulator and using the extended form factor formula. The surface conductivity used in the calculations was extracted from the measured LC after wetting rate. LC characteristics under 1 : 1, 1 : 2, 1 : 5 and 1 : 10 ratios of top to bottom surface salt deposit density on polymeric insulators are studied. To verify the proposed models of this study, the results of experimental data and two other approaches are compared with together before dry-band formation. Moreover, a dynamic LC model under uniform pollution layer has been introduced and extended in order to calculate the LC when the formation of dry-bands along the insulator surface occurs. The dynamic model is drawn from experimental data and measured surface conductivity.

https://ietresearch.onlinelibrary.wiley.com/doi/epdf/10.1049/iet-gtd.2016.2101

Leakage current analysis of polymeric insulators under uniform and non-uniform pollution conditions

Investigation and analysis of AC flashover voltage of SiR insulators under longitudinal and fan-shaped non-uniform pollutions

Because of their advantages over glass and porcelain insulators, composite insulators are being used now in power transmission lines for different voltage rating levels. Recently, the 400 kV level is introduced by Societe Nationale de l'Electricite et du Gaz, SONELGAZ (Algerian Company of Electric Power and Gas) where glass insulators are installed. For better electrical performances, we propose in this paper to integrate composite insulators in a three phase 400 kV AC double circuit line situated in the northwest of Algeria. A comparison is done between the already existing glass insulators and the proposed composite insulator in terms of electric field distribution. The electric field is studied along the leakage paths of the insulators under different surface conditions (dry and clean, uniformly and non uniformly polluted, and in presence of water droplets). Three composite insulators with different shed configurations are proposed. From these three configurations, we selected the insulator presenting lower electric field magnitude in critical areas mainly on the triple point junction (air — HV end — housing material interface). On the double circuit line, we focused our study on the phase insulator that presents the highest electrical stress. Impact of hardware fittings, tower, phases and conductors on the electric field distribution has been analyzed. Effects of bundled conductors have been also studied. Simulations were carried out by employing 2D Finite Element Method (FEM) using COMSOL Multiphysics® 4.3 software. Results show that electric field is lower in the case of composite insulators. Furthermore, we found that the calculation model can be simplified by not considering all circuit phases. Note that appropriate corona rings are considered on both HV and ground ends for glass and composite insulators and their geometrical parameters (corona ring diameter, corona ring tube diameter and corona ring height) are kept constant throughout the whole study.

Improvement of electric field distribution by integrating composite insulators in a 400 kV AC double circuit line in Algeria

This paper presents a theoretical model for evaluating flashover performance of insulators under contaminated conditions. The model introduces several new features when compared with existing models such as, the formation of dry bands, variations in insulator geometry and surface wettability. The electric field distribution obtained from software for 3-Dimensional models along with form factor are used to determine the dimensions of the dry bands and the onset of arcing. The model draws heavily from experimental measurements of flashover voltage and surface resistance under wet conditions of porcelain and composite insulators. The model illustrates the dominant role played by the insulator shape and housing material on the flashover performance.

L. Bo

Papers

Modeling flashover of AC outdoor insulators under contaminated conditions with dry band formation and arcing