Material characterization for elastosonographic phantoms

Summary of the vitro studies. The objective of this in vitro study was to create a phantom witch the same muscle architecture (fiber, aponeurosis …) and mechanical properties of muscle in passive and active states. Two homogeneous phantoms were manufactured with different concentrations of plastisol to simulate the muscle elastic properties in passive (50% of plastisol) and active (70% of plastisol) muscle conditions. Moreover, teflon tubing pipes (D = 0.9 mm) were thread in the upper part of the phantom (50%) to represent the muscle fibers and a plastic sheet (8 x 15 cm) was also included in the middle of the phantom to mimic the aponeurosis structure. Subsequently, MRE tests were performed at 90Hz with two different pneumatic drivers, tube and round shapes, to analyze the effect of the type of driver on the wave propagation. The wavelength was measured from the phase images and the elastic properties (shear modulus) were calculated. Both phantoms revealed elastic properties which were in the same range as in vivo muscle in passive (2.40 ± 0.18 kPa) and active (6.24 ± 0.21 kPa) states. The impact of the type of driver showed higher values with the tube (range: 1.2 kPa to 1.53 kPa). The analysis of the wave behavior revealed a sliding along the plastic sheet as it was observed for in vivo muscle study. The wave was also sensitive to the presence of the fibers where gaps were identified. A new post processing method was established to measure G’ and G” from experimental multi frequencies (60, 80, 100 Hz) MRE (MMRE) tests and rheological models. This method was tested on the phantom (50%) made without fiber. Cross validation of the viscoelastic (G’, G”) results was made with Hyper-Frequency Viscoelastic Spectroscopy (HFVS). Both techniques showed similar range of values for G’ and G” at the same frequencies. This last result validated our new data processing for the viscoelastic measurement. Summary of the in vivo studies. The objective of this in vivo study was to develop MRE protocols to characterize the elastic properties (shear modulus) of the nine thigh muscles. These tests were performed at a single frequency (90Hz). Different shear moduli were found between the muscles. The gracilis revealed the highest elastic properties compared to all the other muscles. These different elasticities may be due to different physiological and architectural compositions between the tissues. Then the viscoelastic properties of the ischio (ST, SM, and BC) and Gr muscles were determined based on our new data-processing method (validated on the phantom 50%) using MMRE tests (70, 90 and 120Hz) and rheological models. The results revealed that two rheological models, zener and springpot, can be used to measure the viscoelastic properties in passive state. A similar trend was found between the experimental ratios G”/G’ obtained at 90 Hz and the α value of the springpot model. The present MRE muscle protocol, and the viscoelastic data base, could be used as non-invasive diagnostic tools to evaluate tissue alterations, the progression of diseases, and the effect of treatments, such as the ongoing therapeutic trials for Duchenne muscular dystrophy.

https://tel.archives-ouvertes.fr/tel-01376744/document

Viscoelastic properties of in vivo thigh muscle and in vivo phantom using magnetic resonance elastography (MRE)

Objective: Realistic tissue-mimicking phantoms are essential for the development, the investigation and the calibration of medical imaging techniques and protocols. Because it requires taking both mechanical and imaging properties into account, the development of robust, calibrated phantoms is a major challenge in elastography. Soft polyvinyl chloride gels in a liquid plasticizer (plastisol or PVCP) have been proposed as soft tissue-mimicking phantoms (TMP) for elasticity imaging. PVCP phantoms are relatively low-cost and can be easily stored over long time periods without any specific requirements. In this work, the preparation of a PVCP gel phantom for both MR and ultrasoundelastography is proposed and its acoustic, NMR and mechanical properties are studied.Material and methods: The acoustic and magnetic resonance imaging properties of PVCP are measured for different mass ratios between ultrasound speckle particles and PVCP solution, and between resin and plasticizer. The linear mechanical properties of plastisol samples are then investigated over time using not only indentation tests, but also MR and ultrasound-elastography clinical protocols. These properties are compared to typical values reported for biological soft tissues and to the values found in the literature for PVCP gels.Results and conclusions: After a period of two weeks, the mechanical properties of the plastisol samples measured with indentation testing are stable for at least the following 4 weeks (end of follow-up period 43 days after gelation-fusion). Neither the mechanical nor the NMR properties of plastisol gels were found to be affected by the addition of cellulose as acoustic speckle. Mechanical properties of the proposed gels were successfully characterized by clinical, commercially-available MR Elastography and sonoelastography protocols. PVCP with a mass ratio of ultrasound speckle particles of 0.6% to 0.8% and a mass ratio between resin and plasticizer between 50 and 70% appears as a good TMP candidate that can be used with both MR and ultrasound-based elastography methods.

Investigation of PVC plastisol tissue-mimicking phantoms for MR-and ultrasound-elastography

In the current context, efficient DFM relying on the ability to manage simultaneously the definitions of the shape, the material and the process, is crucial. The aim of this article is to illustrate, for plastic injection moulding, how to tackle such a situation. To reach our target, computer aided engineering systems should enable to manage the mutual links between the product properties and the product and process parameters. Such a system integrated to conventional computer aided design (CAD) environment and its supporting design process are detailed. The main idea consists in checking systematically the mutual influences between the part and mould CAD models. The design process has two main design sequences: the part driven one and the mould driven one. The proposed architecture is implemented into the commercial CAD environment PTC ProEngineer. The use of the computer system is illustrated on a real study case dealing.

Laurence Meylheuc

Papers

Investigation of PVC plastisol tissue-mimicking phantoms for MR-and ultrasound-elastography

Design for manufacture: the case of concurrent mould and part design in injection moulding