A system and method for combining power from DC power sources. Each power source is coupled to a converter. Each converter converts input power to output power by monitoring and maintaining the input power at a maximum power point. Substantially all input power is converted to the output power, and the controlling is performed by allowing output voltage of the converter to vary. The converters are coupled in series. An inverter is connected in parallel with the series connection of the converters and inverts a DC input to the inverter from the converters into an AC output. The inverter maintains the voltage at the inverter input at a desirable voltage by varying the amount of the series current drawn from the converters. The series current and the output power of the converters, determine the output voltage at each converter.

Distributed Power Harvesting Systems Using DC Power Sources

This letter proposes a three-level buck converter for tracking applications such as envelope-tracking in radio frequency power amplifiers (RFPAs). It is shown that the three-level buck converter can offer advantages in terms of switching ripples, losses, bandwidth, or the size of magnetic components compared to a standard buck or a two-phase buck converter. Experimental results illustrate improved efficiency and ripple rejection in an RFPA envelope-tracking application representative for low-power battery-operated systems.

Three-level buck converter for envelope tracking applications

Using a bidirectional dc-dc converter along with low-voltage energy storage for the high-voltage dc bus and traction motor drives has been a prominent option for hybrid electric and fuel cell vehicles. This paper will describe the significance of energy management power converters and their circuit topology options for efficiency, size, and cost considera- tions. Whether isolated or nonisolated, soft switching techni- ques have been widely used in high-power bidirectional dc-dc converters. Through some design examples, the component selection and circuit design optimization are discussed, and their efficiency evaluation results are also given. Major difficulties of developing a high-power bidirectional dc-dc converter are found in lack of high-power passive components and lack of multiphase dc-dc controllers. More development work needs to be done in these areas.

http://ieeexplore.ieee.org/iel5/5/4168011/04168025.pdf

Energy Management Power Converters in Hybrid Electric and Fuel Cell Vehicles Suitable switching devices and passive electrical components, for increasing the efficient handling of high-power conversion required by these vehicles, are not yet available.

Method for distributed power harvesting using DC power sources

With the advent of battery-powered portable devices and mandatory adoption of power factor correction, noninverting buck-boost converters are garnering lots of attention. Conventional two-switch or four-switch noninverting buck-boost converters choose their operation modes by measuring input and output voltage magnitude. The criterion for the selection of the operation mode can cause higher output voltage transients in the neighborhood, where input and output are close to each other. For the mode selection, due to the voltage drops raised by the parasitic components, it is not enough just to compare the magnitude of input and output voltages. In addition, the difference in the minimum and maximum effective duty cycles between controller output and switching device yields discontinuity at the instant of mode change. Moreover, the different properties of output voltage versus a given duty cycle of buck and boost operating modes contribute to the output voltage transients. In this paper, the effect of the discontinuity due to the effective duty cycle derived from the device switching time at the mode change is analyzed. A technique to compensate the output voltage transient due to this discontinuity is proposed. In order to attain additional mitigation of output transients and a linear input/output voltage characteristic in buck and boost modes, the linearization of DC gain of the large-signal model in boost operation is analyzed as well. Analytical, simulation, and experimental results are presented to validate the proposed theory.

A Compensation Technique for Smooth Transitions in a Noninverting Buck–Boost Converter

A cascade of buck and boost converter is presented here. The control operates in a manner that the converter is either in buck or boost (BOB) mode on a cycle by cycle basis. It transitions between the modes seamlessly to provide a tracking power conversion function for modulating the power supply of a variable envelope radio frequency (RF) power amplifier. The control algorithm and its implementation using switched capacitor circuits is described. Simulation and measured experimental results including converter efficiency, tracking accuracy, and spectrum at the output of the RF power amplifier are provided. This control technique allows seamless transition between the buck and boost modes while tracking RF envelopes with bandwidth greater than 100 kHz, and maintaining extreme accuracy and extremely low ripple. The efficiency of this converter operating at 1.68 MHz is close to 90% over a wide range of conversion ratios. The area of the power converter is extremely small allowing this to be integrated into a cellular telephone. The controller was integrated as part of a larger power management IC as well as a discrete IC.

M. Miller

Papers

Buck or boost tracking power converter