A transformerless high gain dc–dc boost converter with reduced voltage stress

High gain DC-DC converters are increasingly being used in solar PV and other renewable generation systems. Satisfactory steady-state and dynamic performance, along with higher efficiency, is a pre-requirement for selecting the converter for these applications. In this paper, a non-inverting high gain DC-DC boost converter has been proposed. The proposed converter has only one switch with continuous input current and reduced voltage stress across switching devices. The operating range of the duty cycle is wider, and it obtains a higher gain at a lower value of the duty cycle. Moreover, the converter has higher efficiency at a lower duty cycle while drawing a continuous input current. The continuous input current is a desirable feature of the dc-dc converter making it suitable for solar photovoltaic applications. The converter’s operation has been discussed in detail and extended to include the real circuit parameters for a practical performance evaluation. The proposed converter has been compared with other similar recently proposed converters on various performance parameters. The loss analysis for the proposed converter has also been carried out. Finally, the simulation has been validated with results from the experimental prototype.

/pdf/a-non-inverting-high-gain-dc-dc-converter-with-continuous-1e6jjqrefv.pdf

A Non-Inverting High Gain DC-DC Converter With Continuous Input Current

High gain dc-dc converters are used in several applications which include solar photovoltaic system, switch-mode power supplies and fuel cells. In this paper, an ultra-high gain dc-dc boost converter is proposed and analyzed in detail. The converter has a gain of six times as compared with the boost converter. The high gain is achieved by utilizing switched inductors and switched capacitors. A modified voltage multiplier cell (VMC) with switched inductors is proposed. The converter has a single switch which makes its operation easy. Moreover, the voltage across the switch, diodes and capacitors are less than the output voltage which increases the overall efficiency of the converter. The converter performance in steady-state is analyzed in detail and it is compared with other latest high gain converters. The working of the converter in non-ideal conditions is also discussed in detail. The loss analysis is done using PLECS software by incorporating the real models of switches and diodes from the datasheet. To confirm and validate the working of the proposed converter a hardware prototype of 200 W is developed in the laboratory. The converter achieves high gain at low duty ratios and its performance is found to be good in open and closed loop conditions.

/pdf/a-new-transformerless-ultra-high-gain-dc-dc-converter-for-dc-2jl5r0g00c.pdf

A New Transformerless Ultra High Gain DC–DC Converter for DC Microgrid Application

This paper presents a novel topology for the single-phase 31-level asymmetrical multilevel inverter accomplished with reduced components count. The proposed topology generates maximum 31-level output voltage with asymmetric DC sources with an H-bridge. The fundamental 13-level multilevel inverter (MLI) topology is realized, and further, the topology is developed for 31-level can be used for renewable energy applications. This reduces the overall components count, cost and size of the system. Rather than the many advantages of MLIs, reliability issues play a significant role due to higher components count to reduce THD. This is a vital challenge for the researchers to increase the reliability with less THD. Several parameters are analyzed for both fundamental 13-level and developed 31-level MLIs such as total standing voltage (TSV), cost function (CF) and power loss. The inverter is tested experimentally with various combinational loads and under dynamic load variations with sudden load disturbances. Total standing voltage with the cost function for the proposed MLI is compared with various topologies published recently and is cost-effective. A detailed comparison of several parameters with graphical representation is made. Less TSV and components requirement is observed for the proposed MLI. The obtained total harmonic distortion (THD) is under IEEE standards. The topology is simulated in MATLAB/Simulink and verified experimentally with a hardware prototype under various conditions.

/pdf/design-and-implementation-of-31-level-asymmetrical-inverter-3j7b3b889r.pdf

Design and Implementation of 31-Level Asymmetrical Inverter With Reduced Components

The growth of renewable energy in the last two decades has led to the development of new power electronic converters. The DC microgrid can operate in standalone mode, or it can be grid-connected. A DC microgrid consists of various distributed generation (DG) units like solar PV arrays, fuel cells, ultracapacitors, and microturbines. The DC-DC converter plays an important role in boosting the output voltage in DC microgrids. DC-DC converters are needed to boost the output voltage so that a common voltage from different sources is available at the DC link. A conventional boost converter (CBC) suffers from the problem of limited voltage gain, and the stress across the switch is usually equal to the output voltage. The output from DG sources is low and requires high-gain boost converters to enhance the output voltage. In this paper, a new high-gain DC-DC converter with quadratic voltage gain and reduced voltage stress across switching devices was proposed. The proposed converter was an improvement over the CBC and quadratic boost converter (QBC). The converter utilized only two switched inductors, two capacitors, and two switches to achieve the gain. The converter was compared with other recently developed topologies in terms of stress, the number of passive components, and voltage stress across switching devices. The loss analysis also was done using the Piecewise Linear Electrical Circuit Simulation (PLCES). The experimental and theoretical analyses closely agreed with each other.

https://www.mdpi.com/1996-1073/14/9/2629/pdf

A New High-Gain DC-DC Converter with Continuous Input Current for DC Microgrid Applications

This paper presents the design of multi-cycle 32-bit Reduced Instruction Set Computer (RISC) processor for better performance and higher speed of operation. The processor is capable of executing more number of instructions with simple design and less critical path delay. The designed processor was simulated and synthesized using Xilinx 14.7 ISE design suite. The processor executes each and every instruction in more than one cycle that's why the term multi-cycle. Each instruction is divided into three main states namely the Fetch state, the Decode state and the Execution state. The first two sates remain the same for all the instruction the last state, however depends on the type of operation performed in that instruction.

Mohammad Zaid

Papers

Design and application of RISC processor