This is the bibliography referenced in the article by Wayne B Nelson titled "A bibliography of accelerated test plans," published in the IEEE Transactions on Reliability June 2005 issue (vol.54, no.2, ISSN 0018-9529).

A bibliography of accelerated test plans part II - references

Optimal simple step stress accelerated life test design for reliability prediction

The effects of input heat of different welding processes on the microstructure, corrosion, and mechanical characteristics of welded duplex stainless steel (DSS) are reviewed. Austenitic stainless steel (ASS) is welded using low-heat inputs. However, owing to differences in the physical metallurgy between ASS and DSS, low-heat inputs should be avoided for DSS. This review highlights the differences in solidification mode and transformation characteristics between ASS and DSS with regard to the heat input in welding processes. Specifically, many studies about the effects of heat energy input in welding process on the pitting corrosion, intergranular stress, stresscorrosion cracking, and mechanical properties of weldments of DSS are reviewed.

Effects of Heat Input on Microstructure, Corrosion and Mechanical Characteristics of Welded Austenitic and Duplex Stainless Steels: A Review

This paper proposes a method of estimating the lifetime distribution at use condition for constant stress accelerated life tests when an extrinsic failure mode as well as intrinsic one exists. A mixture of two distributions is introduced to describe these failure modes. It is assumed that the log lifetime of each failure mode follows a location-scale distribution and a linear relation exists between the location parameter and the stress. An estimation procedure using the expectation and maximization algorithm is proposed and specific formulas for Weibull distribution are obtained. Simulation studies are performed to investigate the properties of the estimates and the effects of stress level. Numerical comparisons with the masked data model are also performed.

Analyses of accelerated life test data under two failure modes

Accelerated testing has been widely used for several decades. Started with accelerated life tests with constant-stress loadings, more interest has been focused prominently on accelerated degradation tests and time-varying stress loadings. Because accelerated testing is crucial to the assessment of product reliability and the design of warranty policy, it is important to develop an efficacious test plan that encompasses and addresses important issues, such as design of stress profiles, sample allocation, test duration, measurement frequency, and budget constraint. In recent years, extensive research has been conducted on the optimal design of accelerated testing plans, and the consideration of multiple stresses with interactions has become a big challenge in such experimental designs. The purpose of this study is to provide a comprehensive review of important methods for statistical inference and optimal design of accelerated testing plans by compiling the existing body of knowledge in the area of accelerated testing. In this work, different types of test planning strategies are categorized, and their drawbacks and the research trends are provided to assist researchers and practitioners in conducting new research in this area.

A literature review on planning and analysis of accelerated testing for reliability assessment

This article presents an optimum simple step-stress accelerated life test for the Weibull distribution under Type I censoring. It is assumed that a log-linear relationship exists between the Weibull scale parameter and the (possibly transformed) stress and that a certain cumulative exposure model for the effect of changing stress holds. The optimum plan—low stress and stress change time—is obtained, which minimizes the asymptotic variance of the maximum likelihood estimator of a stated percentile at design stress. For selected values of the design parameters, nomographs useful for finding the optimum plan are given, and the effects of errors in preestimates of the parameters are investigated. As an alternative to the simple step-stress test, a three-level compromise plan is proposed, and its performance is studied and compared with that of the optimum simple step-stress test. © 1993 John Wiley & Sons. Inc.

Optimum simple step-stress accelerated life tests for Weibull distribution and type I censoring

Experimental studies in various aspects have to be conducted to maintain stable applications of super duplex stainless steels (SDSS) because the occurrence rate of sigma phase, variable temperature and growth direction of sigma phase can influence mechanical performances of SDSS. Tensile tests of precipitated SDSS were performed under various temperatures to analyze mechanical and morphological behavior.

Low-Temperature Mechanical Behavior of Super Duplex Stainless Steel with Sigma Precipitation

304L stainless steel sheets are used as a primary barrier for the insulation of membrane-type liquefied natural gas(LNG) carrier cargo containment system. 304L stainless steel is a transformation-induced-plasticity(TRIP) steel that exhibits complex material behavior, because it undergoes phase transformation during plastic deformation. Since the TRIP behavior is very important mechanical characteristics in a low-temperature environment, significant amounts of data are available in the literature. In the present study, a uniaxial tensile test for 304L stainless steel was performed to investigate nonlinear mechanical characteristics. In addition, a viscoplastic model and damage model is proposed to predict material fractures under arbitrary loads. The verification was conducted not only by a material-based comparative study involving experimental investigations, but also by a structural application to the LNG membrane of a Mark-III-type cargo containment system.

/pdf/numerical-simulation-of-membrane-of-lng-insulation-system-2rqwqdn5yd.pdf

Numerical Simulation of Membrane of LNG Insulation System using User Defined Material Subroutine

LNG (liquefied natural gas) is considered the best alternative eco-fuel, and many studies on the LNG fuel system have been performed to use LNG as the fuel for ships. For the LNG fuel supply system, natural gas transfers from the vapor- izer to the engine in the gaseous state with a temperature of 50℃ and a pressure of 35MPa. Therefore, a structural safety evaluation of the double-walled pipelines considering thermal load is essential. In this article, an uniaxial tensile test for super duplex stainless steel, material for double-walled pipe, according to the annealing time was carried out to analyze the thermal effect. In addition, thermo-structural analysis of the high temperature-high pressure double-walled pipe with fixed supports that are now used widely was carried out to evaluate the structural safety. To minimize stress concentration of the connection point between the support and inner pipe, the shapes of the new type support that can slip through inner pipe were proposed, and the supports which has best structural performance was selected using the results from the thermo-structural analyses of new supports and an analysis of the whole double-walled pipeline was performed to ensure structural safety. These results can be used as a database for the design of double-walled pipelines and sliding support.

http://koreascience.or.kr:80/article/JAKO201518564558586.pdf

A Study of Thermo-Mechanical Analysis for the Design of High Pressure Piping System for Natural Gas Fuel Vessel

Super duplex stainless steels (sDSS) are excellent for use under severely corrosive conditions such as offshore and marine applications like pipelines and flanges. sDSS has better mechanical properties and corrosion resistance than the standard duplex stainless steel (DSS) but it is easier for a sigma phase to appear, which depresses the mechanical property and corrosion resistance, compared to DSS, because sDSS has a higher alloy element than DSS. In addition, sDSS has a feeble ductile-brittle transition temperature (DBTT) because it has a 50% ferrite microstructure. In the actual operating environment, sDSS would be thermally affected by welding and a sub-zero temperature environment. This study analyzed how precipitated sDSS behaves ata sub-zero temperature through annealing heat treatment and a sub-zero tensile test. Six types of specimens with annealing times of up to 60 min were tested in a sub-zero chamber. According to the experimental results, an increase in the annealing time reduced the elongation of sDSS, and a decrease in the tensile test temperature raises the flow stress and tensile stress. In particular, the elongation of specimens annealed for 15 min and 30 min was clearly lowered with a decrease in the tensile test temperature because of the increasing sigma phase fraction ratio.

http://koreascience.or.kr:80/article/JAKO201426059105532.pdf

Myung-Soo Kim

Papers

Optimum simple step-stress accelerated life tests for Weibull distribution and type I censoring

Low-Temperature Mechanical Behavior of Super Duplex Stainless Steel with Sigma Precipitation

Numerical Simulation of Membrane of LNG Insulation System using User Defined Material Subroutine

A Study of Thermo-Mechanical Analysis for the Design of High Pressure Piping System for Natural Gas Fuel Vessel

Low-temperature Mechanical Behavior of Super Duplex Stainless Steel Considering High Temperature Environment