An object is to provide a semiconductor device of which a manufacturing process is not complicated and by which cost can be suppressed, by forming a thin film transistor using an oxide semiconductor film typified by zinc oxide, and a manufacturing method thereof. For the semiconductor device, a gate electrode is formed over a substrate; a gate insulating film is formed covering the gate electrode; an oxide semiconductor film is formed over the gate insulating film; and a first conductive film and a second conductive film are formed over the oxide semiconductor film. The oxide semiconductor film has at least a crystallized region in a channel region.

Semiconductor device, and manufacturing method thereof

Modern computer microprocessor chips are marvels of engineering complexity. For the current 45 nm technology node, there may be nearly a billion transistors on a chip barely 1 cm2 and more than 10 000 m of wiring connecting and powering these devices distributed over 9-10 wiring levels. This represents quite an advance from the first INTEL 4004B microprocessor chip introduced in 1971 with 10 μm minimum dimensions and 2 300 transistors on the chip! It has been disclosed that advanced microprocessor chips at the 32 nm node will have more than 2 billion transistors.1 For instance, Figure 1 shows a sectional 3D image of a 90 nm IBM microprocessor, containing several hundred million integrated devices and 10 levels of interconnect wiring, designated as the back-end-of-the-line (BEOL). Since the invention of microprocessors, the number of active devices on a chip has been exponentially increasing, approximately doubling every two years. This trend was first described in 1965 by Gordon Moore,2 although the original discussion suggested doubling the number of devices every year, and the phenomenon became popularly known as Moore’s Law. This progress has proven remarkably resilient and has persisted for more than 50 years. The enabler that has permitted these advances is known as scaling, that is, the reduction of minimum device dimensions by lithographic advances (photoresists, tooling, and process integration optimization) by ∼30% for each device generation.3 It allowed more active devices to be incorporated in a given area and improved the operating characteristics of the individual transistors. It should be emphasized that the earlier improvements in chip performance were achieved with very few changes in the materials used in the construction of the chips themselves. The increase of performance with scaling * Corresponding author. E-mail: gdubois@us.ibm.com. † IBM Almaden Research Center. ‡ Stanford University. Willi Volksen received his B.S. in Chemistry (magna cum laude) from New Mexico Institute of Mining and Technology in 1972 and his Ph.D. in Chemistry/Polymer Science from the University of Massachusetts, Lowell, in 1975. He then joined the research group of Prof. Harry Gray/Dr. Alan Rembaum at the California Institute of Technology as a postdoctoral fellow and upon completion of the one-year appointment joined Dr. Rembaum at the Jet Propulsion Laboratory as a Senior Chemist in 1976. In 1977 Dr. Volksen joined the IBM Research Division at the IBM Almaden Research Center in San Jose, CA, where he is an active research staff member in the Advanced Materials Group of the Science and Technology function.

Low dielectric constant materials.

Process gas discharged from a bypass pipe to a gas exhaust system can be prevented from diffusing back to the inside of a process chamber without having to install a dedicated vacuum pump at the downstream side of the bypass pipe. The substrate processing apparatus includes a process chamber accommodating a substrate, a gas supply system supplying process gas from a process gas source to the process chamber for processing the substrate, a gas exhaust system configured to exhaust the process chamber, two or more vacuum pumps installed in series at the gas exhaust system, and a bypass pipe connected between the gas supply system and the gas exhaust system. The most upstream one of the vacuum pumps is a mechanical booster pump, and the bypass pipe is connected between the mechanical booster pump and the rest vacuum pumps located at a downstream side of the mechanical booster pump.

Substrate Processing Apparatus

A silicon dioxide-based dielectric layer is formed on a substrate surface by a sequential deposition/anneal technique. The deposited layer thickness is insufficient to prevent substantially complete penetration of annealing process agents into the layer and migration of water out of the layer. The dielectric layer is then annealed, ideally at a moderate temperature, to remove water and thereby fully densify the film. The deposition and anneal processes are then repeated until a desired dielectric film thickness is achieved.

Sequential deposition/anneal film densification method

A method of forming a layer on a substrate in a chamber, wherein the substrate has at least one formed feature across its surface, is provided. The method includes exposing the substrate to a silicon-containing precursor in the presence of a plasma to deposit a layer, treating the deposited layer with a plasma, and repeating the exposing and treating until a desired thickness of the layer is obtained. The plasma may be generated from an oxygen-containing gas.

Method to improve the step coverage and pattern loading for dielectric films

Temperature dependence of SiO2 film growth with plasma-enhanced atomic layer deposition

A method for increasing mechanical strength of a dielectric film includes: providing an initial dielectric film containing porogen; irradiating the initial dielectric film with first UV light having a first wavelength which is substantially or nearly similar to a maximum light absorption wavelength of the porogen for removing the porogen; and then irradiating the porogen-removed dielectric film with second UV light having a second wavelength which is shorter than the first wavelength, thereby increasing mechanical strength of the dielectric film.

Method for increasing mechanical strength of dielectric film by using sequential combination of two types of uv irradiation

A method for forming a silicon-containing dielectric film on a substrate by atomic layer deposition (ALD) includes: providing two precursors, one precursor containing a halogen in its molecule, another precursor containing a silicon but no halogen in its molecule, adsorbing a first precursor, which is one of the two precursors onto a substrate to deposit a monolayer of the first precursor; adsorbing a second precursor, which is the other of the two precursors onto the monolayer of the first precursor to deposit a monolayer of the second precursor; and exposing the monolayer of the second precursor to radicals of a reactant to cause surface reaction with the radicals to form a compound monolayer of a silicon-containing film.

Method for forming Si-containing film using two precursors by ALD

A UV irradiation apparatus for processing a semiconductor substrate includes: a UV lamp unit having at least one dielectric barrier discharge excimer lamp which is constituted by a luminous tube containing a rare gas wherein an inner surface of the luminous tube is coated with a fluorescent substance having a peak emission spectrum in a wavelength range of 190 nm to 350 nm; and a reaction chamber disposed under the UV lamp unit and connected thereto via a transmission window.

UV-Curing Apparatus Provided With Wavelength-Tuned Excimer Lamp and Method of Processing Semiconductor Substrate Using Same

A UV irradiation apparatus for processing a semiconductor substrate includes: a UV lamp unit; a reaction chamber disposed under the UV lamp unit; a gas ring with nozzles serving as a first electrode between the UV lamp unit and the reaction chamber; a transmission window supported by the gas ring; an RF shield which covers a surface of the transmission window facing the UV lamp unit; a second electrode disposed in the reaction chamber for generating a plasma between the first and second electrodes; and an RF power source for supplying RF power to one of the first or second electrode.

Naoto Tsuji

Papers

Temperature dependence of SiO2 film growth with plasma-enhanced atomic layer deposition

Method for increasing mechanical strength of dielectric film by using sequential combination of two types of uv irradiation

Method for forming Si-containing film using two precursors by ALD

UV-Curing Apparatus Provided With Wavelength-Tuned Excimer Lamp and Method of Processing Semiconductor Substrate Using Same

UV Irradiation Apparatus with Cleaning Mechanism and Method for Cleaning UV Irradiation Apparatus