Calculations of the impact of friction and wear on energy consumption, economic expenditure, and CO2 emissions are presented on a global scale. This impact study covers the four main energy consuming sectors: transportation, manufacturing, power generation, and residential. Previously published four case studies on passenger cars, trucks and buses, paper machines and the mining industry were included in our detailed calculations as reference data in our current analyses. The following can be concluded:

 Fifty years ago, wear and wear-related failures were a major concern for UK industry and their mitigation was considered to be the major contributor to potential economic savings by as much as 95% in ten years by the development and deployment of new tribological solutions. The corresponding estimated savings are today still of the same orders but the calculated contribution to cost reduction is about 74% by friction reduction and to 26% from better wear protection. Overall, wear appears to be more critical than friction as it may result in catastrophic failures and operational breakdowns that can adversely impact productivity and hence cost.

/pdf/influence-of-tribology-on-global-energy-consumption-costs-pgu0i0z95u.pdf

Influence of tribology on global energy consumption, costs and emissions

Laser melting (LM), with a focused Nd: YAG laser beam, was used to form solid bodies from a 316L austenite stainless steel powder. The microstructure, phase content and texture of the LM stainless steel were characterized and compared with conventional 316L stainless steel. The crack-free LM samples achieved a relative density of 98.6±0.1%. The XRD pattern revealed a single phase Austenite with preferential crystallite growth along the (100) plane and an orientation degree of 0.84 on the building surface. A fine columnar sub-grain structure of size 0.5 μm was observed inside each individual large grain of single-crystal nature and with grain sizes in the range of 10–100 μm. Molybdenum was found to be enriched at the sub-grain boundaries accompanied with high dislocation concentrations. It was proposed that such a sub-grain structure is formed by the compositional fluctuation due to the slow kinetics of homogeneous alloying of large Mo atoms during rapid solidification. The local enrichment of misplaced Mo in the Austenite lattice induced a network of dislocation tangling, which would retard or even block the migration of newly formed dislocations under indentation force, turning otherwise a soft Austenite to hardened steel. In addition, local formation of spherical nano-inclusions of an amorphous chromium-containing silicate was observed. The origin and the implications of the formation of such oxide nano-inclusions were discussed.

Hardened austenite steel with columnar sub-grain structure formed by laser melting

The mechanical properties and corrosion resistance of 316 L stainless steel fabricated using the Laser Engineered Net Shaping (LENS) technique have been studied. The crack-free, full density samples made using SS316L alloy powder and the LENS technique are characterized by an unusual distinct dual-phase microstructure. STEM analysis revealed a significant increase of Cr and Mo content and a decrease of Ni in the grain boundaries. Based on the Cr and Ni content (austenite stabilizing elements), the Schaeffler diagram and the EBSD results, the existence of intercellular delta ferrite on subgrain boundaries and austenite in the fine-grains are observed. The XRD patterns, in addition to the FCC austenite phase, revealed the second BCC ferrite phase. Moreover, the sigma (FeCr) phases are present in the analyzed 316 L stainless steel. The occurrence of ferrite, which does not occur in regular stainless steel fabricated using conventional metallurgical methods, improves the mechanical and corrosion properties of the LENS-fabricated sample made using 316 L stainless steel powder. The obtained results prove that the microstructure of the SS316L fabricated using LENS is heterogeneous; its impact on the mechanical properties is visible. The analyzed samples are characterized by anisotropic mechanical properties that are favorable. For both the perpendicular and parallel directions of tensile tests, samples had a ductile fracture with many dimples inside of the larger dimples. The corrosion potential of SS316L LENS and classically manufactured steel is similar. The SS316L fabricated using LENS is characterized by a relatively low value of corrosion current density, which translates into much smaller corrosion rates.

The microstructure, mechanical properties and corrosion resistance of 316 L stainless steel fabricated using laser engineered net shaping

Stereolithography is a solid freeform technique (SFF) that was introduced in the late 1980s Although many other techniques have been developed since then, stereolithography remains one of the most powerful and versatile of all SFF techniques It has the highest fabrication accuracy and an increasing number of materials that can be processed is becoming available In this paper we discuss the characteristic features of the stereolithography technique and compare it to other SFF techniques The biomedical applications of stereolithography are reviewed, as well as the biodegradable resin materials that have been developed for use with stereolithography Finally, an overview of the application of stereolithography in preparing porous structures for tissue engineering is given

Remzi Varol

Papers

Surface severe plastic deformation of AISI 304 via conventional shot peening, severe shot peening and repeening

Almen intensity effect on microstructure and mechanical properties of low carbon steel subjected to severe shot peening

Effect of shot peening on the oxidation behavior of thermal barrier coatings

Mechanical properties of P/M 316L stainless steel materials

Effect of severe shot peening and ultra-low temperature plasma nitriding on Ti-6Al-4V alloy