The analysis of the small-signal stability of conventional power systems is well established, but for inverter based microgrids there is a need to establish how circuit and control features give rise to particular oscillatory modes and which of these have poor damping. This paper develops the modeling and analysis of autonomous operation of inverter-based microgrids. Each sub-module is modeled in state-space form and all are combined together on a common reference frame. The model captures the detail of the control loops of the inverter but not the switching action. Some inverter modes are found at relatively high frequency and so a full dynamic model of the network (rather than an algebraic impedance model) is used. The complete model is linearized around an operating point and the resulting system matrix is used to derive the eigenvalues. The eigenvalues (termed "modes") indicate the frequency and damping of oscillatory components in the transient response. A sensitivity analysis is also presented which helps identifying the origin of each of the modes and identify possible feedback signals for design of controllers to improve the system stability. With experience it is possible to simplify the model (reduce the order) if particular modes are not of interest as is the case with synchronous machine models. Experimental results from a microgrid of three 10-kW inverters are used to verify the results obtained from the model

Modeling, Analysis and Testing of Autonomous Operation of an Inverter-Based Microgrid

Microgrids: an overview of ongoing research, development, anddemonstration projects

Droop control is the basic control method for load current sharing in dc microgrid applications. The conventional dc droop control method is realized by linearly reducing the dc output voltage as the output current increases. This method has two limitations. First, with the consideration of line resistance in a droop-controlled dc microgrid, since the output voltage of each converter cannot be exactly the same, the output current sharing accuracy is degraded. Second, the dc-bus voltage deviation increases with the load due to the droop action. In this paper, in order to improve the performance of the dc microgrid operation, a low-bandwidth communication (LBC)-based improved droop control method is proposed. In contrast with the conventional approach, the control system does not require a centralized secondary controller. Instead, it uses local controllers and the LBC network to exchange information between converter units. The droop controller is employed to achieve independent operation, and the average voltage and current controllers are used in each converter to simultaneously enhance the current sharing accuracy and restore the dc bus voltage. All of the controllers are realized locally, and the LBC system is only used for changing the values of the dc voltage and current. Hence, a decentralized control scheme is accomplished. The simulation test based on MATLAB/Simulink and the experimental validation based on a 2 × 2.2 kW prototype were implemented to demonstrate the proposed approach.

/pdf/an-improved-droop-control-method-for-dc-microgrids-based-on-3a15g7qxoy.pdf

An Improved Droop Control Method for DC Microgrids Based on Low Bandwidth Communication With DC Bus Voltage Restoration and Enhanced Current Sharing Accuracy

In this paper, the control strategy for a flexible microgrid is presented. The microgrid presented here consists of several line-interactive uninterruptible power supply (UPS) systems connected in parallel. The control technique is based on the droop method to avoid critical communications among UPS units. Thus, a flexible microgrid is obtained to operate in either grid-connected or islanded mode. A small-signal analysis is presented in order to analyze the system stability, which gives rules to design the main control parameters. Simulation and experimental results are presented, showing the feasibility of the proposed controller.

Control Strategy for Flexible Microgrid Based on Parallel Line-Interactive UPS Systems

Microgrids and Active Distribution Networks offer a potential solution for sustainable, energy-efficient power supply to cater for increasing load growth, supplying power to remote areas, generation of clean power and reduction in emission of greenhouse gases & particulates as per Kyoto protocol.

Microgrids and Active Distribution Networks

Evolutionary changes in the regulatory and operational climate of traditional electric utilities and the emergence of smaller generating systems such as microturbines have opened new opportunities for on-site power generation by electricity users. In this context, distributed energy resources (DER)--small power generators typically located at users' sites where the energy (both electric and thermal) they generate is used--have emerged as a promising option to meet growing customer needs for electric power with an emphasis on reliability and power quality. The portfolio of DER includes generators, energy storage, load control, and, for certain classes of systems, advanced power electronic interfaces between the generators and the bulk power provider. This white paper proposes that the significant potential of smaller DER to meet customers' and utilities' needs can be best captured by organizing these resources into MicroGrids.

/pdf/integration-of-distributed-energy-resources-the-certs-44141k7sc2.pdf

Ross Guttromsom

Papers

Integration of distributed energy resources. The CERTS Microgrid Concept