https://escholarship.org/content/qt8rf718jm/qt8rf718jm.pdf?t=krnesf

Recent Advances in Mechanical Micromachining

The miniaturization of machine components is perceived by many as a requirement for the future technological development of a broad spectrum of products. Miniature components can provide smaller footprints, lower power consumption and higher heat transfer, since their surface-to-volume ratio is very high. To create these components, micro-meso-scale fabrication using miniaturized mechanical material removal processes has a unique advantage in creating 3D components using a variety of engineering materials. The motivation for micro-mechanical cutting stems from the translation of the knowledge obtained from the macro-machining domain to the micro-domain. However, there are challenges and limitations to micro-machining, and simple scaling cannot be used to model the phenomena of micro-machining operations. This paper surveys the current efforts in mechanical micro-machining research and applications, especially for micro-milling operations, and suggests areas from macro-machining that should be examined and researched for application to the improvement of micro-machining processes.

Investigation of micro-cutting operations

This study investigates the critical maximum undeformed equivalent chip thickness for ductile-brittle transition (DBhmax-e) of zirconia ceramics under different lubrication conditions. A DBhmax-e model is developed through geometry and kinematics analyses of ductile-mode grinding. Result shows that DBhmax-e decreases with increasing friction coefficient (μ). An experimental investigation is then conducted to validate the model and determine the effect of dry lubrication, minimum quantity lubrication (MQL), and nanoparticle jet minimum quantity lubrication (NJMQL) conditions on DBhmax-e. According to different formation mechanisms of debris, the grinding behavior of zirconia ceramics is categorized into elastic sliding friction, plastic removal, powder removal, and brittle removal. Grinding forces per unit undeformed chip thickness (Fn/h and Ft/h) are obtained. The lubrication condition affects the normal force and ultimately influences the resultant force on workpiece. In comparison with dry grinding (DBhmax-e = 0.8 μm), MQL and NJMQL grinding processes increase DBhmax-e by 0.99 and 1.79 μm respectively; this finding is similar to model result. The theoretical model is then assessed by different volume fractions of nanofluids under NJMQL condition with an average percentage error of less than 8.6%.

Maximum undeformed equivalent chip thickness for ductile-brittle transition of zirconia ceramics under different lubrication conditions

The market for freeform and high quality microdies and moulds made of steel is predicted to experience a phenomenal growth in line with the demand for microsystems. However, micromachining of hardened steel is a challenge due to unpredictable tool life and likely differences in process mechanism compared to macro-scale machining. This paper presents an investigation of the size effect in micromilling of H13 hardened tool steel. In this case, the size effect in micromilling hardened tool steel was observed by studying the effect of the ratio of undeformed chip thickness to the cutting edge radius on process performance. The paper explores how this ratio drives the specific cutting force, surface finish and burr formation in micro-scale machining. In addition, the effect of different microend mill geometry on product quality was explored. The paper provides a valuable insight into optimum micro-scale machining conditions for obtaining the best surface finish and minimizing burr size.

Size effect and tool geometry in micromilling of tool steel

Ultra-precision machining (UPM) is capable of manufacturing a high quality surface at a nanometric surface roughness. For such high quality surface in a UPM process, due to the machining complexity any variable would be possible to deteriorate surface quality, consequently receiving much attention and interest. The general factors are summarized as machine tool, cutting conditions, tool geometry, environmental conditions, material property, chip formation, tool wear, vibration etc. This paper aims to review the current state of the art in studying the surface roughness formation and the factors influencing surface roughness in UPM. Firstly, the surface roughness characteristics in UPM is introduced. Then in UPM, a wide variety of factors for surface roughness are then reviewed in detail and the mechanism of surface roughness formation is concluded thoroughly. Finally, the challenges and opportunities faced by industry and academia are discussed and several principle conclusions are drawn.

A review of surface roughness generation in ultra-precision machining

In the ultra precision diamond cutting process, the rake angle of the tool is likely to become negative because the edge radius of tool is considerably large compared to the sub-micrometer depth of cut. The round edge of the tool might sometimes cause plowing results in a poor surface, or burnishing which results in a shiny surface depending on the depth of cut. This study deals with the relationship between the friction of a tool-workpiece and the minimum cutting thickness in micro cutting. Proposed is an ultra precision cutting model in which the tool edge radius and the friction coefficient are the principal factors determining the minimum cutting thickness with a continuous chip. According to the model, a smaller edge radius and a higher friction coefficient make the cutting depth thinner. The experimental results verify the proposed model and provide various supporting evidence.

Effects of the friction coefficient on the minimum cutting thickness in micro cutting

Influences of pulsed power condition on the machining properties in micro EDM

Burr and shape distortion are two main problems in micro-grooving. In this study, a simplified model is proposed based on large thrust force due to the tool edge radius. Experiments are conducted with a single crystal diamond tool on a 3-axis shaper-like machine varying the depth of cuts, and groove angles on brass, aluminum and OFHC. Experiments have shown that the thrust force becomes a dominant variable in burr generation compared to the principal force when the depth of cut is less than 2 μm. And fewer burrs develop on more brittle materials. Shape distortion is significant only when the groove angle is small and the depth of cut is larger than 30 μm.

Burr and Shape Distortion in Micro-Grooving of Non-Ferrous Metals Using a Diamond tool

Characteristics of Micro-Machining Using Two-Dimensional Tool Vibration

Ultra precision diamond cutting is a very efficient manufacturing method for optical parts such as HOE, Fresnel lenses, diffraction lenses, and others. During micro cutting, the rake angle is likely to become negative because the tool edge radius is considerably large compared to the sub-micrometer-order depth of cut. Depending on the ratio of the tool edge radius to the depth of cut, different micro-cutting mechanism modes appear. Therefore, the tool edge sharpness is the most important factor which affects the qualities of machined parts. That is why diamond, especially monocrystal diamond which has the sharpest edge among all other materials, is widely used in micro-cutting. The majar issue is regarding the minimum (critical) depth of cut needed to obtain continuous chips during the cutting process. In this paper, the micro machinability near the critical depth of cut is investigated in micro grooving with a diamond tool. The experimental results show the characteristics of micro-cutting in terms of cutting force ratio (Fx/Fy), chip shape, surface roughness, and surface hardening near the critical depth of cut.

https://koreascience.or.kr:443/article/JAKO200311921519225.pdf

Seong-Min Son

Papers

Effects of the friction coefficient on the minimum cutting thickness in micro cutting

Influences of pulsed power condition on the machining properties in micro EDM

Burr and Shape Distortion in Micro-Grooving of Non-Ferrous Metals Using a Diamond tool

Characteristics of Micro-Machining Using Two-Dimensional Tool Vibration

A Study on Critical Depth of Cuts in Micro Grooving