Cold atmospheric plasma: Sources, processes, and applications

This paper reviews the last twenty years of work concerning surface flashover of insulators in vacuum. It complements an earlier review paper [H.C. Miller, Flashover of Insulators in Vacuum, IEEE Trans. Electr .Insul., Vol. 28, pp. 512-527, 1993]. The surface flashover voltage of insulators in vacuum depends upon many parameters, such as material, geometry, surface finish, and attachments to electrodes, but also on the applied voltage waveform, duration, single pulse or repetitive, and on the process history of the insulator, operating environment, and previous applications of voltage. Suggestions are made for choosing the material, geometry, and processing when selecting an insulator for a particular application. Some specific techniques for improving the holdoff voltage of insulators are recommended.

Flashover of insulators in vacuum: the last twenty years

Al2O3 nanoparticles were synthesized using laser ablation of an aluminum (Al) target in deionized water. Nd:YAG laser, emitted the light at a wavelength of 1064 nm, was used as a light source. The laser ablation was carried out at different energies of 1, 3, and 5 J. The structure of ablated Al particles suspended in deionized water was investigated using X-ray diffraction (XRD). The XRD patterns revealed that the ablated Al particles transformed into γ-Al2O3. The morphology of nanoparticles was investigated by field emission scanning electron microscopy (FE-SEM). The FE-SEM images showed that most of the nanoparticles obtained from all the ablated laser energies have spherical shape with a particle size of less than 100 nm. Furthermore, it was observed that the particle size increased with increasing the laser energy. The absorption spectra of Al2O3 nanoparticles suspended in deionized water were recorded at room temperature using UV-visible spectroscopy. The absorption spectra show a strong peak at 210nm arising from the presence of Al2O3 nanoparticles. The results on absorption spectra are in good agreement with those investigated by XRD which confirmed the formation of Al2O3 nanoparticles during the laser ablation of Al target in deionized water.

/pdf/preparation-and-characterization-of-alumina-nanoparticles-in-3ywwidb94d.pdf

Preparation and characterization of alumina nanoparticles in deionized water using laser ablation technique

Dielectric window breakdown is a serious challenge in high-power microwave (HPM) transmission and radiation. Breakdown at the vacuum/dielectric interface is triggered by multipactor and finally realized by plasma avalanche in the ambient desorbed or evaporated gas layer above the dielectric. Methods of improving breakdown thresholds are key challenges in HPM systems. First, the main theoretical and experimental progress is reviewed. Next, the mechanisms of multipactor suppression for periodic rectangular and triangular surface profiles by dynamic analysis and particle-in-cell simulations are surveyed. Improved HPM breakdown thresholds are demonstrated by proof-of-principle and multigigawatt experiments. The current theories and experiments of using dc magnetic field to resonantly accelerate electrons to suppress multipactor are also synthesized. These methods of periodic profiles and magnetic field may solve the key issues of HPM vacuum dielectric breakdown.

Review of recent theories and experiments for improving high-power microwave window breakdown thresholdsa)

Sintering of Ceramics - New Emerging Techniques

The breakdown of alumina rf windows is mostly caused by multipactor, as well as by material defects and contamination. Since multipator induces localized surface heating, leading to surface melting, it is necessary to observe secondary electron emission (SEE) coefficients of alumina ceramics under high temperature conditions. The SEE coefficients of commercial alumina ceramics and sapphire were measured by a scanning electron microscopy (SEM) with a single short-pulsed electron beam (100 pA, 1 ms) at room temperature and at 650degC. Additive materials used for sintering alumina, such as SiO 2 and MgO, were also investigated. Surface charging evaluations have also become important because the accumulated charges are discharged at the threshold Held, resulting in surface discharge. The surface charging evaluations were carried out by multi-pulse measurements with the injection of successive pulses on the sample. As a result, reductions in the SEE coefficients with temperature were confirmed, except for sapphire. The multi-pulse measurement results indicated that surface charging of the sapphire was higher than that of other samples. This may be one of the factors that causes sapphire not to be durable for rf window applications, compared with alumina ceramics. Although there are few exceptions, it was found that the SEE coefficients of alumina ceramics increased with the purity and the average grain size

Secondary electron emission and surface charging evaluation of alumina ceramics and sapphire

Secondary electron emission of sapphire and anti-multipactor coatings at high temperature

Secondary electron emission of TiN-coated alumina ceramics

This paper presents a comparative study of various controllers for the speed control of Brushless Direct Current Motor (BLDCM) to improve a performance of control. The most commonly used controller for the speed control of BLDCM is Proportional Integral Derivative (PID) controller. However, the PID controller has advantages such as: a good response, the simple structure and robustness of method, but it has disadvantages such as: optimally tuning gains of PID have been quit difficult and it cannot adapt a non-linier state of plant. Further, ANFIS controller has the ability to automatically learn and adapt with a state of plant. A novel hybrid controller that combines the advantages of PID controller and ANFIS controller is desired to improve the response of plant. To model of BLDCM is used an identification system method. Simulation results are presented and analyzed for all the controllers. It is observed that hybrid PID-ANFIS based controllers give better responses than PID or ANFIS for the speed control of BLDCM drive.

A comparative study of PID, ANFIS and hybrid PID-ANFIS controllers for speed control of Brushless DC Motor drive

The effect of surface roughness of insulator on the secondary electron emission (SEE) coefficients was investigated with changing the incident angle of primary electrons. The SEE coefficients were measured using a scanning electron microscope with a single-pulse electron beam (100 pA, 1 ms). As a result, the SEE coefficients increased with the incident angle for smooth surface, while those of rough surface almost did not change with the incident angle. The SEE coefficients of commercial alumina ceramics with three different surface finishes, i.e. as-sintered, as-ground and mirror-finished samples, were also measured before and after annealing treatments. This treatment was carried out in air at 1400 degC for 1 h. After annealing, the SEE coefficients were higher than those of unannealed samples. This increase is proposed to be due to the defect recoveries as well as neutralizations of charging, which significantly influence the SEE. For relative low purity (95% or less), the SEE coefficients of annealed alumina became lower after mechanical grinding operations and lower again after mirror-finished operations. The SEE coefficients of 99.7% purity alumina were almost unaffected by the mechanical finishes.

Suharyanto

Papers

Secondary electron emission and surface charging evaluation of alumina ceramics and sapphire

Secondary electron emission of sapphire and anti-multipactor coatings at high temperature

Secondary electron emission of TiN-coated alumina ceramics

A comparative study of PID, ANFIS and hybrid PID-ANFIS controllers for speed control of Brushless DC Motor drive

Effect of mechanical finishes on secondary electron emission of alumina ceramics