PI fiber insulation paper has excellent insulation and heat resistance, which can replace traditional insulation paper to provide a new high-performance material. In this paper, we adopt a two-step method to synthesize PI, that is, firstly synthesize polyamic acid, and then perform electrospinning and thermal imidization to prepare PI porous fiber membrane. The test results show that the breakdown field strength of the PI porous film is 50 kV/mm. Further research shows that the insulation structure has the characteristics of continuous multiple breakdown. When the fiber film is repeatedly broken down to 25 times at the same point, the field strength of each breakdown of the fiber film changes between 40 and 55 kV/mm, and the average breakdown field strength is 53 kV/mm. Nano-Al2O3 was introduced into the fiber membrane by in situ polymerization. The breakdown field strength of the composite fiber film can reach 74.89 kV/mm after doping 2 wt% nano-Al2O3, which is higher than that of the pure film. At the same time, this kind of fiber paper also has repeatable breakdown characteristics, and the breakdown voltage distribution width of multiple breakdown is reduced. This characteristic provides the maintenance free characteristic of DC over-voltage for the insulation structure composed of this fiber paper, and can improve the service life of transformer under DC over-voltage such as lightning stroke.

Preparation of PI porous fiber membrane for recovering oil-paper insulation structure

ower transformers are one of the most expensive elements in a power system, and their failure is a very costly event. Power transformers are mainly involved in energy transmission and distribution. Unplanned power transformer outages have considerable economic impact on the operation of electric power networks. To have reliable operation of transformers, it is necessary to identify problems at an early stage before a catastrophic failure occurs. In spite of corrective and predictive maintenance, preventive maintenance is gaining due importance in the modern era, and it must be taken into account to obtain the highest reliability of power apparatus such as power transformers. The well-known preventive maintenance techniques such as dissolved gas analysis (DGA), thermal monitoring, partial discharge measurement, capacitance and tan delta measurements, frequency response analysis, etc. are performed on transformers for a specific type of problem. DGA is a very efficient and reliable tool for the earliest detection of inception faults in transformer and other electrical equipment using insulating oil. Condition monitoring of electrical equipment, such as transformers, helps users in many ways such as planning of maintenance schedule, obtaining knowledge of the health of equipment, estimating the remaining service life of equipment, finding areas of further improvement, refining product specification, etc. Kraft paper (cellulose) immersed in mineral oil is used as the insulation system for the copper windings in large power transformers. As the system ages under load, the paper and oil can degrade, potentially leading to catastrophic failure. Partial discharge (PD) is an important tool for improving the reliability of HV insulation systems. It is a very sensitive and nondestructive method of evaluation of the health of the insulation of any HV equipment. PD always is associated with the degradation of insulation systems in HV equipment. Therefore, PDs need to be detected, measured, located, and reduced to a safe value so that the quality of the insulation system is not affected.

Condition Monitoring of Power Transformers - Bibliography Survey

The article makes a case for allowing higher temperatures in transformers filled with natural ester fluids. This article will first provide a review of data from aging studies performed on cellulose (both Kraft paper and pressboard) impregnated separately in mineral oil and BIOTEMP (ABB, USA), a high oleic sunflower based fluid. Next, possible mechanisms that explain the differences in aging behavior will be discussed. The article concludes with recommendations for new temperature limits for BIOTEMP-impregnated transformers in comparison with mineral-oil-impregnated transformers.

A survey of aging characteristics of cellulose insulation in natural ester and mineral oil

Nanotechnology applications for electrical transformers—A review

Power transformers are a key component of electrical networks, and they are both expensive and difficult to upgrade in a live network. Many utilities monitor the condition of the components that make up a power transformer and use this information to minimize the outage and extend the service life. Routine and diagnostic tests are currently used for condition monitoring and appraising the ageing and defects of the core, windings, bushings and tap changers of power transformers. To accurately assess the remaining life and failure probability, methods have been developed to correlate results from different routine and diagnostic tests. This paper reviews established tests such as dissolved gas analysis, oil characteristic tests, dielectric response, frequency response analysis, partial discharge, infrared thermograph test, turns ratio, power factor, transformer contact resistance, and insulation resistance measurements. It also considers the methods widely used for health index, lifetime estimation, and probability of failure. The authors also highlight the strengths and limitations of currently available methods. This paper summarizes a wide range of techniques drawn from industry and academic sources and contrasts them in a unified frame work.

A review of condition monitoring techniques and diagnostic tests for lifetime estimation of power transformers

This paper examines the practical aspects of the usage of cellulose insulation in transformers with regard to maintaining the integrity over long periods of time and preserving and extending insulation life. The factors that relate to loss of life are examined and life plots are discussed in more detail.

T.A. Prevost

Papers

Cellulose insulation in oil-filled power transformers: part II maintaining insulation integrity and life