Preface Acknowledgments 1. Introduction 2. Dispersion principles 3. Unbounded isotropic and anisotropic media 4. Reflection and refraction 5. Oblique incidence 6. Waves in plates 7. Surface and subsurface waves 8. Finite element method for guided wave mechanics 9. The semi-analytical finite element method (SAFE) 10. Guided waves in hollow cylinders 11. Circumferential guided waves 12. Guided waves in layered structures 13. Source influence on guided wave excitation 14. Horizontal shear 15. Guided waves in anisotropic media 16. Guided wave phased arrays in piping 17. Guided waves in viscoelastic media 18. Ultrasonic vibrations 19. Guided wave array transducers 20. Introduction to guided wave nonlinear methods 21. Guided wave imaging methods Appendix A: ultrasonic nondestructive testing principles, analysis and display technology Appendix B: basic formulas and concepts in the theory of elasticity Appendix C: physically based signal processing concepts for guided waves Appendix D: guided wave mode and frequency selection tips.

Ultrasonic Guided Waves in Solid Media

Ultrasonic guided wave inspection is expanding rapidly to many different areas of manufacturing and in-service inspection. The purpose of this paper is to provide a vision of ultrasonic guided wave inspection potential aswe move forward into the new millennium. An increased understanding of the basic physics and wave mechanics associated with guided wave inspection has led to an increase in practical nondestructive evaluation and inspection problems. Some fundamental concepts and a number of different applications that are currently being considered will be presented in the paper along with a brief description of the sensor and software technology that will make ultrasonic guided wave inspection commonplace in the next century.

A Baseline and Vision of Ultrasonic Guided Wave Inspection Potential

Piezoelectric wafer active sensors may be applied on aging aircraft structures to monitor the onset and progress of structural damage such as fatigue cracks and corrosion. The state of the art in piezoelectric-wafer active sensors structural health monitoring and damage detection is reviewed. Methods based on (a) elastic wave propagation and (b) the Electro–Mechanical (E/M) impedance technique are cited and briefly discussed. For health monitoring of aging aircraft structures, two main detection strategies are considered: the E/M impedance method for near field damage detection, and wave propagation methods for far-field damage detection. These methods are developed and verified on simple-geometry specimens and on realistic aging aircraft panels with seeded cracks and corrosion. The experimental methods, signal processing, and damage detection algorithms are tuned to the specific method used for structural interrogation. In the E/M impedance method approach, the high-frequency spectrum, representative of the structural resonances, is recorded. Then, overallstatistics damage metrics can be used to compare the impedance signatures and correlate the change in these signatures with the damage progression and intensity. In our experiments, the (1 � R 2 ) 3 damage metric was found to best fit the results in the 300–450 kHz band. In the wave propagation approach, the pulse-echo and acousto-ultrasonic methods can be utilized to identify the additional reflections generated from crack damage and the changes in transmission phase and velocity associated with corrosion damage. The paper ends with a conceptual design of a structural health monitoring system and suggestions for aging aircraft installation utilizing active-sensor arrays, data concentrators, wireless transmission, and a health monitoring and processing unit.

/pdf/piezoelectric-wafer-embedded-active-sensors-for-aging-4jqff5fle9.pdf

Piezoelectric Wafer Embedded Active Sensors for Aging Aircraft Structural Health Monitoring

http://www.mkckorea.com/catalog/qseeman/hc-200_ref8.pdf

Corrosion Monitoring of Reinforced Concrete Structures - A Review

Recent theoretical and experimental studies demonstrated that a weakly or incompletely bonded interfaces exhibit highly nonlinear behavior. One of acoustic manifestations of such nonlinearity is the modulation of a probing high-frequency ultrasonic wave by low-frequency vibration. The vibration varies the contact area modulating the phase and amplitude of higher frequency probing wave passing through the interface. In the frequency domain, the result of this modulation manifests itself as side-band spectral components with respect to the frequency of the probing wave. This modulation effect has been observed experimentally for various materials (metals, composites, concrete, sandstone, glass) with various types of contact-type defects (interfaces): cracks, debondings, delaminations, and microstructural material damages. Study of this phenomenon revealed correlation between the developed modulation criterion and the quantitative characteristics of the interfaces, such as its size, loading condition, and bonding strength. These findings have been used for the development of an innovative nondestructive evaluation technique, namely Vibro-Acoustic Modulation Technique. Two modifications of this technique have been developed: Vibro-Modulation (VM) and Impact-Modulation (IM), employing CW and impact-induced vibrations, respectively. The examples of applications of these methods include crack detection in steel pipes, aircraft and auto parts, bonded composite plates etc. These methods also proved their effectiveness in the detection of cracks in concrete.

Nonlinear acoustic interaction on contact interfaces and its use for nondestructive testing

An ultrasonic apparatus for testing a material comprises an oscillator (10) which generates a selected frequency in the ultrasonic range. A transducer (1) is connected to the oscillator (10) for applying an ultrasonic signal to the material and for receiving an echo signal back from the material. A phase detector (5) receives the echo signal and an in-phase oscillator signal to generate a first display signal, and a phase detector (6) receives a quadrature signal (90° out of phase from the oscillator signal) and the echo signal to generate a second display signal. The first and second display signals are utilised in a visual display, such as a cathode ray tube (8), to generate an image. The image changes according to the phase shift between the ultrasonic signal transmitted into the material and the echo signal, which, in turn, can be utilised to determine the presence and depth of a flaw or boundary in the material.

Ultrasonic testing of materials

A method of determining low density deposits on the inner surface of a boiler tube comprises the generation of ultrasonic energy which is directed from the outer surface of the tube to the inner surface of the tube. The energy is reflected back and forth between the inner and outer surfaces with each reflection of the inner surface loosing energy by attenuation into any existing low density deposit. The first and fourth reflections are measured and digitized for analysis to determine the amount of attenuation. The amount of attenuation is representative of the low density deposit on the inner surface of the tube. The tube is preferably empty of water to avoid transmission of ultrasonic energy through water in the tube.

Method for determining deposit buildup

Verfahren und einrichtung zum lokalisieren defekter brennstaebe eines reaktor- brennelements

An ultrasonic search unit for locating defective fuel elements within a fuel assembly used in a water cooled nuclear reactor is presented. The unit is capable of freely traversing the restricted spaces between the fuel elements.

Apparatus for locating defective nuclear fuel elements

Defects in nuclear fuel elements are ascertained and located within an assembled fuel assembly by ultrasonic means. In a typical embodiment of the invention, an ultrasonic search unit is positioned within the fuel assembly opposite the lower plenum of the fuel element to be tested. An ultrasonic pulse is radially projected into the element. Defective fuel elements are ascertained by ultrasonic reflection measurements.

William E. Lawrie

Papers

Ultrasonic testing of materials

Method for determining deposit buildup

Verfahren und einrichtung zum lokalisieren defekter brennstaebe eines reaktor- brennelements

Apparatus for locating defective nuclear fuel elements

Method for locating defective nuclear fuel elements