This paper presents a comprehensive study on the state-of-the-art and emerging wind energy technologies from the electrical engineering perspective. In an attempt to decrease cost of energy, increase the wind energy conversion efficiency, reliability, power density, and comply with the stringent grid codes, the electric generators and power electronic converters have emerged in a rigorous manner. From the market based survey, the most successful generator-converter configurations are addressed along with few promising topologies available in the literature. The back-to-back connected converters, passive generator-side converters, converters for multiphase generators, and converters without intermediate dc-link are investigated for high-power wind energy conversion systems (WECS), and presented in low and medium voltage category. The onshore and offshore wind farm configurations are analyzed with respect to the series/parallel connection of wind turbine ac/dc output terminals, and high voltage ac/dc transmission. The fault-ride through compliance methods used in the induction and synchronous generator based WECS are also discussed. The past, present and future trends in megawatt WECS are reviewed in terms of mechanical and electrical technologies, integration to power systems, and control theory. The important survey results, and technical merits and demerits of various WECS electrical systems are summarized by tables. The list of current and future wind turbines are also provided along with technical details.

High-Power Wind Energy Conversion Systems: State-of-the-Art and Emerging Technologies

Doubly fed induction generator (DFIG) technology is the dominant technology in the growing global market for wind power generation, due to the combination of variable-speed operation and a cost-effective partially rated power converter. However, the DFIG is sensitive to dips in supply voltage and without specific protection to “ride-through” grid faults, a DFIG risks damage to its power converter due to overcurrent and/or overvoltage. Conventional converter protection via a sustained period of rotor-crowbar closed circuit leads to poor power output and sustained suppression of the stator voltages. A new minimum-threshold rotor-crowbar method is presented in this paper, improving fault response by reducing crowbar application periods to 11-16 ms, successfully diverting transient overcurrents, and restoring good power control within 45 ms of both fault initiation and clearance, thus enabling the DFIG to meet grid-code fault-ride-through requirements. The new method is experimentally verified and evaluated using a 7.5-kW test facility.

Minimum-Threshold Crowbar for a Fault-Ride-Through Grid-Code-Compliant DFIG Wind Turbine

The application of a dynamic voltage restorer (DVR) connected to a wind-turbine-driven doubly fed induction generator (DFIG) is investigated. The setup allows the wind turbine system an uninterruptible fault ride-through of voltage dips. The DVR can compensate the faulty line voltage, while the DFIG wind turbine can continue its nominal operation as demanded in actual grid codes. Simulation results for a 2 MW wind turbine and measurement results on a 22 kW laboratory setup are presented, especially for asymmetrical grid faults. They show the effectiveness of the DVR in comparison to the low-voltage ride-through of the DFIG using a crowbar that does not allow continuous reactive power production.

/pdf/fault-ride-through-of-a-dfig-wind-turbine-using-a-dynamic-1kl4tp229a.pdf

Fault Ride-Through of a DFIG Wind Turbine Using a Dynamic Voltage Restorer During Symmetrical and Asymmetrical Grid Faults

This paper presents a comprehensive study on the latest grid code regulations enforced by transmission system operators on large wind power plants (WPPs). First, the most common requirements included in the majority of international grid codes are compared; namely, low and high voltage ride-through capabilities, active and reactive power responses during and after faults, extended range of voltage–frequency variations, active power (frequency) control facility, and reactive power (voltage) regulation support. The paper also presents a discussion on the global harmonization of international grid codes as well as future trends expected in the regulations. Finally, the evolution of different wind generator technologies to fulfill various grid code requirements is investigated. The presented study will assist system operators to establish their connection requirements for the first time or to compare their existing regulations with other operators. It also enables wind turbine manufacturers and wind farm developers to obtain a more precise understanding from the latest international requirements imposed on modern wind farms.

Review of international grid codes for wind power integration: Diversity, technology and a case for global standard

Review of contribution to frequency control through variable speed wind turbine

Fault ride-through (FRT) is required for large wind farms in most power systems. Fixed speed wind turbines (FSWTs) are a diminishing but significant sector in the fast-growing wind turbine (WT) market. State-of-art techniques applied to meet grid requirements for FSWT wind farms are blade pitching and dynamic reactive power compensation (RPC). Blade pitching is constrained by the onerous mechanical loads imposed on a wind turbine during rapid power restoration. Dynamic RPC is constrained by its high capital cost. These present technologies can therefore be limiting, especially when connecting to smaller power systems. A novel alternative technology is proposed that inserts series resistance into the generation circuit. The series dynamic braking resistor (SDBR) dissipates active power and boosts generator voltage, potentially displacing the need for pitch control and dynamic RPC. This paper uses a representative wind farm model to study the beneficial effect of SDBR compared to dynamic RPC. This is achieved by quasi-steady-state characterization and transient FRT stability simulations. The analysis shows that SDBR can substantially improve the FRT performance of a FSWT wind farm. It also shows that a small resistance, inserted for less than one

/pdf/fault-ride-through-of-large-wind-farms-using-series-dynamic-2rcbicnuh0.pdf

A. Causebrook

Papers

Fault Ride-Through of Large Wind Farms Using Series Dynamic Braking Resistors (March 2007)