The soil-water characteristic curve can be used to estimate various parameters used to describe unsaturated soil behaviour. A general equation for the soil-water characteristic curve is proposed. A nonlinear, least-squares computer program is used to determine the best-fit parameters for experimental data presented in the literature. The equation is based on the assumption that the shape of the soil-water characteristic curve is dependent upon the pore-size distribution of the soil (i.e., the desaturation is a function of the pore-size distribution). The equation has the form of an integrated frequency distribution curve. The equation provides a good fit for sand, silt, and clay soils over the entire suction range from 0 to 106 kPa. Key words : soil-water characteristic curve, pore-size distribution, nonlinear curve fitting, soil suction, water content.

Equations for the soil-water characteristic curve

The Paper presents a constitutive model for describing the stress-strain behaviour of partially saturated soils. The model is formulated within the framework of hardening plasticity using two iodependent sets of stress variables: the excess of total stress over air pressure and the suction. The mode1 is able to represent, in a consistent and unified manner, many of the fundamental features of the behaviour of partially saturated soils which had been treated separately by previously proposed models. On reaching saturation, the mode1 becomes a conventional critical state model. Because experimental evidence is still limited, the model has been kept as simple as possible in order to provide a basic framework from which extensions are possible. Tbe mode1 is intended for partially saturated soils which are slightly or moderately expansive. After formulating the model for isotropic and biaxial stress states, typical predictions are described and compared, in a qualitative way, with characteristic trends of the behaviour of partially saturated soils. Afterwards, the results of a number of suction-controlled laboratory tests on compacted kaolin and a sandy clay are used to evaluate the ability of the model to reproduce, quantitatively, observed behaviour. The agreement between observed and computed results is considered satisfactory and confirms the possibilities of reproducing the most important features of partially saturated soil behaviour using a simple general framework.

A constitutive model for partially saturated soils

The Paper presents a constitutive model for describing the stress-strain behaviour of partially saturated soils. The model is formulated within the framework of hardening plasticity using two independent sets of stress variables: the excess of total stress over air pressure and the suction. The model is able to represent, in a consistent and unified manner, many of the fundamental features of the behaviour of partially saturated soils which had been treated separately by previously proposed models. On reaching saturation, the model becomes a conventional critical state model. Because experimental evidence is still limited, the model has been kept as simple as possible in order to provide a basic framework from which extensions are possible. The model is intended for partially saturated soils which are slightly or moderately expansive. After formulating the model for isotropic and triaxial stress states, typical predictions are described and compared, in a qualitative way, with characteristic trends of the...

/pdf/a-constitutive-model-for-partially-saturated-soils-2qcca1f1md.pdf

A Constitutive Model for Partially Saturated Soils

Soils can rarely be described as ideally elastic or perfectly plastic and yet simple elastic and plastic models form the basis for the most traditional geotechnical engineering calculations. With the advent of cheap powerful computers the possibility of performing analyses based on more realistic models has become widely available. One of the aims of this book is to describe the basic ingredients of a family of simple elastic-plastic models of soil behaviour and to demonstrate how such models can be used in numerical analyses. Such numerical analyses are often regarded as mysterious black boxes but a proper appreciation of their worth requires an understanding of the numerical models on which they are based. Though the models on which this book concentrates are simple, understanding of these will indicate the ways in which more sophisticated models will perform.

Soil Behaviour and Critical State Soil Mechanics

The validity of the cubic law for laminar flow of fluids through open fractures consisting of parallel planar plates has been established by others over a wide range of conditions with apertures ranging down to a minimum of 0.2 µm. The law may be given in simplified form by Q/Δh = C(2b)3, where Q is the flow rate, Δh is the difference in hydraulic head, C is a constant that depends on the flow geometry and fluid properties, and 2b is the fracture aperture. The validity of this law for flow in a closed fracture where the surfaces are in contact and the aperture is being decreased under stress has been investigated at room temperature by using homogeneous samples of granite, basalt, and marble. Tension fractures were artificially induced, and the laboratory setup used radial as well as straight flow geometries. Apertures ranged from 250 down to 4µm, which was the minimum size that could be attained under a normal stress of 20 MPa. The cubic law was found to be valid whether the fracture surfaces were held open or were being closed under stress, and the results are not dependent on rock type. Permeability was uniquely defined by fracture aperture and was independent of the stress history used in these investigations. The effects of deviations from the ideal parallel plate concept only cause an apparent reduction in flow and may be incorporated into the cubic law by replacing C by C/ƒ. The factor ƒ varied from 1.04 to 1.65 in these investigations. The model of a fracture that is being closed under normal stress is visualized as being controlled by the strength of the asperities that are in contact. These contact areas are able to withstand significant stresses while maintaining space for fluids to continue to flow as the fracture aperture decreases. The controlling factor is the magnitude of the aperture, and since flow depends on (2b)3, a slight change in aperture evidently can easily dominate any other change in the geometry of the flow field. Thus one does not see any noticeable shift in the correlations of our experimental results in passing from a condition where the fracture surfaces were held open to one where the surfaces were being closed under stress.

/pdf/validity-of-cubic-law-for-fluid-flow-in-a-deformable-rock-2ynq4id3hq.pdf

VALIDITY OF CUBIC LAW FOR FLUID FLOW IN A DEFORMABLE ROCK FRACTURE - eScholarship

Mapping of cracked soils and lateral water flow characteristics through a network of cracks

The determination of soil-water characteristic curve (SWCC) is of major concern in unsaturated soil mechanics. For decades experimental and theoretical studies are performed to investigate the constitutive relationship between soil suction and volumetric water content. The major objective of our study is to generate an extensive experimental database for sand with a relevant suction range of just a few kPa. This database enables to derive conclusions on the sensitivity of hydraulic properties regarding different experimental procedures. Further, one objective is the comparison of results for SWCC derived from steady state and transient state tests. While the first type of tests considers equilibrium states, the subsequent test is related to non-equilibrium states. Experimental results are generated from a so called homogenous element test (modified pressure plate apparatus) and an initial boundary value experiment (column testing device) considering different hydraulic loading path directions. The experiments are analysed for sand with different initial states. Finally results are presented for SWCC including initial curves, main curves, and scanning paths. Discussion is focused on transient state versus steady state flow tests. No significant dynamic effects are observed for the sand studied. Results of well controlled element tests compare very well to initial boundary value experiments implying higher experimental efforts.

Modified Pressure Plate Apparatus and Column Testing Device for Measuring SWCC of Sand

The diffusion of air through saturated high air entry discs presents a serious problem in the testing of unsaturated soils. When determining either the strength (drained) or volume change character...

A Diffused Air Volume Indicator for Unsaturated Soils

Rainwater infiltration is of particular interest with respect to slope stability hazard management. The process of rainfall infiltration into unsaturated soil is complex due to the number of soil parameters involved and the random nature of moisture flux boundary conditions. In this paper, the effect of rainfall intensity on infiltration is investigated through the use of finite element seepage modeling for a 5 m high soil column subjected to various rainfall intensities. The numerical modeling study identified three response parameters that can be used to describe one-dimensional infiltration into an unsaturated soil. The response parameters are the depth of wetting front, the matric suction reduction depth, and the sectional infiltration rate. The practical application of the rainfall response parameters in slope stability analysis is illustrated.

Response parameters for characterization of infiltration

Design of effective capillary barrier systems requires a thorough understanding of the soilwater interactions that take place in both coarse- and fine-grained unsaturated soils. Experimental observations of water flow through coarse porous media are presented to gain greater understanding of the processes and mechanisms that contribute to the movement and retention of water in coarse-grained unsaturated soils. The use of pendular ring theory to describe how water is held within a porous material with relatively low volumetric water contents is explored. Experimental measurements of seepage velocity and volumetric water content were obtained for columns of 12 mm glass beads using digital videography to capture the movement of a dye tracer front at several infiltration rates. An estimated curve for hydraulic conductivity versus matric suction is shown and compared to a theoretical curve. The method is shown to provide a reasonable predictive tool.Key words: soil-water characteristic curve, hydraulic conduc...

Delwyn G. Fredlund

Papers

Mapping of cracked soils and lateral water flow characteristics through a network of cracks

Modified Pressure Plate Apparatus and Column Testing Device for Measuring SWCC of Sand

A Diffused Air Volume Indicator for Unsaturated Soils

Response parameters for characterization of infiltration

Unsaturated flow in coarse porous media