In this study, we developed and validated a refined three-dimensional finite element model of middle femoral comminuted fracture to compare the biomechanical stability after two kinds of plate fixation: a newly designed assembly locking compression plate (NALCP) and a locking compression plate (LCP). CT data of a male volunteer was converted to middle femoral comminuted fracture finite element analysis model. The fracture was fixated by NALCP and LCP. Stress distributions were observed. Under slow walking load and torsion load, the stress distribution tendency of the two plates was roughly uniform. The anterolateral femur was the tension stress area, and the bone block shifted toward the anterolateral femur. Maximum stress was found on the lateral border of the number 5 countersink of the plate. Under a slow walking load, the NALCP maximum stress was 2.160e+03 MPa and the LCP was 8.561e+02 MPa. Under torsion load, the NALCP maximum stress was 2.260e+03 MPa and the LCP was 6.813e+02 MPa. Based on those results of finite element analysis, the NALCP can provide adequate mechanical stability for comminuted fractures, which would help fixate the bone block and promote bone healing.

/pdf/biomechanical-property-of-a-newly-designed-assembly-locking-1y2bonbs6n.pdf

Biomechanical Property of a Newly Designed Assembly Locking Compression Plate: Three-Dimensional Finite Element Analysis.

Biomechanical analysis for five fixation techniques of Pauwels-III fracture by finite element modeling

Intralesional curettage versus prosthetic replacement for bone tumors - a finite element analysis case of limb salvage simulation in biomechanics

Objective We wanted to analyze the factors affecting the results of multiple cannulated screws fixation in patients less than 60 years old with femoral neck fracture (FNF). Methods We reviewed 52 patients (30 males, 22 females) who were treated with multiple cannulated screws fixation for FNFs. They were followed up for more than one year during January 2002 to December 2012. They were classified by Garden's classification. The anatomic reduction was evaluated by Garden's alignment index on hip both anteroposterior and lateral images. Postoperative complications were analyzed during follow up periods. Results By Garden's classification, 6 cases were in stage I, 13 cases in stage II, 30 cases in stage III and 3 cases in stage IV. During follow up periods, avascular necrosis of the femoral head was observed in 12 cases (23%) and nonunion was observed in 5 cases (9%). The 16 patients who had complications underwent total hip arthroplasty (31%). In non-displaced fracture groups (Garde I, II) did not have AVN nor nonunion. The incidence of complications in displaced fracture group was 51.5%. The complicated cases showed tendency for increased apex anterior angulation of femoral neck on hip lateral images and the result was statistically significant. (p=0.0260). Conclusion The patients less than 60 years old who were treated with multiple cannulated screws fixation for displaced FNFs showed the incidence of complications was more than 50%. It needs a cautious approach for anatomical reduction, especially related to anterior angulation on hip lateral image.

Multiple cannulated screw fixation of young femoral neck fractures.

Purpose: Based on rapid modeling 1 year after intramedullary nailing, personalized finite element modeling analysis was performed to predict whether the broken ends of fractured bones would break again after nail dislodgement. Methods: A total of 10 male volunteers with femur fractures who had undergone intramedullary nailing were selected 1 year after fixation and were divided into healing (n=5) and non-healing (n=5) groups based on X-ray analysis. We modeled each femoral fracture and performed finite element analyses after the intramedullary nail was dislodged. Static loads and constraints were applied to each model to simulate a person standing on one leg. Results: In the healing group, the von Mises stress concentrations and stress concentration point distribution were located outside the bone healing area, indicating that the stress was not concentrated at the fracture site. In the non-healing group, the maximum von Mises stress for various materials was located in the broken ends of the fractured bo...

Personalized finite element modeling analysis of femur bone healing after intramedullary nailing

OBJECTIVE Finite element analysis was used to compare preoperative and postoperative stress distribution of a bone healing model of femur fracture, to identify whether broken ends of fractured bone would break or not after fixation dislodgement one year after intramedullary nailing. Method s: Using fast, personalized imaging, bone healing models of femur fracture were constructed based on data from multi-slice spiral computed tomography using Mimics, Geomagic Studio, and Abaqus software packages. The intramedullary pin was removed by Boolean operations before fixation was dislodged. Loads were applied on each model to simulate a person standing on one leg. The von Mises stress distribution, maximum stress, and its location was observed. Results : According to 10 kinds of display groups based on material assignment, the nodes of maximum and minimum von Mises stress were the same before and after dislodgement, and all nodes of maximum von Mises stress were outside the fracture line. The maximum von Mises stress node was situated at the bottom quarter of the femur. The von Mises stress distribution was identical before and after surgery. Conclusion : Fast, personalized model establishment can simulate fixation dislodgement before operation, and personalized finite element analysis was performed to successfully predict whether nail dislodgement would disrupt femur fracture or not.

/pdf/finite-element-analysis-of-a-bone-healing-model-1-year-14bcodpcgd.pdf

Du Cheng-Fei

Papers

Finite element analysis of a bone healing model: 1-year follow-up after internal fixation surgery for femoral fracture.