There is a large number of materials that can be used for FDM additive manufacturing technology. These materials have different strength properties, they are designed for different purposes. They can be highly strong or flexible, abrasion-resistant, or designed for example for environments with higher thermal loads. However recently new innovative and progressive materials have come to the practice, which include nano-composite particles, bringing new added value. One such material is the Conductive PLA material, which is capable of conducting electric current. The aim of this article is to present the material properties of this material. The article describes the design of the experiment, the process of measuring the resistance of samples printed by FDM device, measuring the maximum tensile strength of samples. The article includes a statistical evaluation of the measured data, with the determination of the significance of individual factors of the experiment as well as the evaluation of the overall result of the experiments.

/pdf/resistance-and-strength-of-conductive-pla-processed-by-fdm-1javbian.pdf

Resistance and Strength of Conductive PLA Processed by FDM Additive Manufacturing

Fused deposition modeling (FDM) printing of commercial and reinforced filaments is a proven and well-explored method for the enhancement of mechanical properties. However, little has hitherto been reported on the multi-material components, fused or laminated together into a single specimen by using the laminated object manufacturing (LOM) technique for sustainable/renewable polymers. TPU is one such durable and flexible, sustainable material exhibiting renewable and biocompatible properties that have been explored very less often in combination with the ABS polymer matrix in a single specimen, such as the LOM specimen. The current research work presents the LOM manufacturing of 3D-printed flexural specimens of two different, widely used polymers available viz. ABS and TPU and tested as per ASTM D790 standards. The specimens were made and laminated in three layers. They were grouped into two categories, namely ABS: TPU: ABS (ATA) and TPU: ABS: TPU (TAT), which are functionally graded, sandwiched structures of polymeric material. The investigation of the flexural properties, microscopic imaging, and porosity characteristics of the specimens was made for the above categories. The results of the study suggest that ATA-based samples held larger flexural strength than TAT laminated manufactured samples. A significant improvement in the peak elongation and break elongation of the samples was achieved and has shown a 187% increase in the break elongation. Similarly, for the TAT-based specimen, flexural strength was improved significantly from approximately 6.8 MPa to 13 MPa, which represents a nearly 92% increase in the flexural strength. The morphological testing using Tool Maker’s microscopic analysis and porosity analysis has supported the observed trends of mechanical behavior of ATA and TAT samples.

/pdf/on-laminated-object-manufactured-fdm-printed-abs-tpu-2j94wkfk.pdf

On Laminated Object Manufactured FDM-Printed ABS/TPU Multimaterial Specimens: An Insight into Mechanical and Morphological Characteristics

Mechanical properties of the FFF sandwich-structured parts made of PLA/TPU multi-material

Three-dimensional printing is widely used in many fields, including engineering, architecture and even medical purposes. The focus of the study is to obtain the ideal weight-to-performance ratio for making a 3D-printed part. The end products of the 3D-printed part are hugely affected by not only the material but also the printing parameters. The printing parameters to be highlighted for this study are the infill density, wall perimeter and layer height, which are the commonly adjusted parameters in 3D printing. The study will be divided into two parts, the simulation analysis and the experimental analysis, to confirm both results toward the trend of Young’s modulus for the material. It will then be analyzed and discussed toward any differences between the two results. The results showed that increasing the value of all three parameters will increase the tensile elasticity of the part.

/pdf/effects-of-infill-density-wall-perimeter-and-layer-height-in-12xlvwa3.pdf

Effects of Infill Density, Wall Perimeter and Layer Height in Fabricating 3D Printing Products

Multi-material products are required in fused deposition modelling (FDM) to meet a desired specification such as a rigid structure with soft material for impact protection. This paper focuses on the thermoformability and shape recovery characteristics of three-dimensional (3D)-printed multi-material specimens under different thermoforming temperatures. The multi-material specimens consist of polylactic acid (PLA) and thermoplastic polyurethane (TPU). The PLA/TPU specimens were prepared by depositing the TPU component on top of the PLA component using a fused deposition modelling (FDM) machine. Simple thermoforming tests were proposed, where the specimens were bent under load and molded into a circular shape at different thermoforming temperatures. The bent specimens were then reheated at 60 °C to evaluate their shape memory ability. The test results were quantified into apparent bending modulus and shape recovery percentage. The PLA/TPU specimens showed a better apparent bending modulus of 143 MPa than a PLA specimen at a temperature between 60 °C to 90 °C. However, only the PLA/TPU specimens being thermoformed into a circular shape at 100 °C or greater showed good shape retention accuracy and interfacial surface bonding. The PLA/TPU specimens that were thermoformed at 60 °C to 90 °C showed reasonable shape memory of about 60% recovery when reheated. Finally, suitable thermoforming temperatures for thermoforming PLA/TPU specimens were suggested based on design needs.

/pdf/thermoforming-characteristics-of-pla-tpu-multi-material-2xntozxn.pdf

Thermoforming Characteristics of PLA/TPU Multi-Material Specimens Fabricated with Fused Deposition Modelling under Different Temperatures

A 3D printer in FDM technology allows printing with two nozzles, which creates an opportunity to produce multi-material elements. Printing from two materials requires special consideration of the interface zone generated between their geometrical boundaries. This article aims to present the possibility of printing with PLA and TPU using commercially available filaments and software to obtain the best possible bond strength between two different polymers with respect to printing parameters, surface pattern (due to the material contact surface’s roughness), and the order of layer application. The interaction at the interface of two surfaces of two different filaments (PLA-TPU and TPU-PLA) and six combinations of patterns were tested by printing seven replicas for each. A total of 12 combinations were obtained. By analyzing pairs of samples (the same patterns, different order of materials), the results for the TPU/PLA samples were better or very close to the results for PLA/TPU. The best variants of pattern combinations were distinguished. Well-chosen printing parameters can prevent a drop in parts efficiency compared to component materials (depending on the materials combination).

Emila Brancewicz-Steinmetz

Papers

The Influence of 3D Printing Parameters on Adhesion between Polylactic Acid (PLA) and Thermoplastic Polyurethane (TPU).