A review of sustainable pervious concrete systems: Emphasis on clogging, material characterization, and environmental aspects

To cater the demand as an alternative pavement material, pervious concrete exhibits an astonishing significance in the field of eco-friendly pavement design system, due to its overall hydrological ...

Pervious concrete as an alternative pavement strategy: a state-of-the-art review

Experimental investigation of the use of pervious concrete on high volume roads

Although porous concrete pavement design methods are mainly focused on maintaining high permeability rates in order to improve their ability to manage stormwater runoff, the mixture strength is paramount for its durability and service life. This paper proposes a new mixture design method for porous concrete, named PCD (porous concrete design), derived from the ACI 522R-10 and ACI 211.3R-02 standards. The aim is to improve mechanical strength in porous concrete mixtures, while ensuring enough permeability for its use in urban roads. With PCD methodology it is possible to obtain mechanical strengths 30% higher than those produced with ACI methodologies, while maintaining permeability rates close to 2 cm/s, lower than those obtained with ACI methods but still enough to manage extreme storm events. Finally, with the analytical Hierarchy Process (AHP) multi-criteria decision-making methodology and also bearing in mind safety variables, the best porous concrete mixtures are the ones produced with PCD methodology.

https://www.mdpi.com/1996-1944/12/19/3100/pdf

Proposal of a New Porous Concrete Dosage Methodology for Pavements

Pervious concrete pavement is a recognized sustainable solution for urban roads. To enhance mechanical properties of pervious concrete material, in order to allow wider use of this technology, a lot of studies are going on all over the world. The use of a little percentage of fine aggregates is proven to increase the material resistance without an excessive reduction of permeability. This study aimed to evaluate the effect of replacing the fine virgin aggregates with r cycled tire rubber. 14 different mixes were analysed in terms of indirect tensile strength resistance, void content and density. Two different dimensions of crumb rubber were studied, as well as two different dosages, which were applied to different no-fine control mixes. All results were compared with the same control mixes containing natural fine aggregate. The mixes had a fixed granulometric curve but varied in water/cement ratio; this in order to evaluate the effect of recycled rubber depending to w/c ratio of the mix. An image analysis was also conducted to verify the rubber distribution in the mixture and the cracking surfaces. The experimental analysis showed that a correct proportioning of fine sand significantly increased the strength of the material. Moreover, the use of recycled waste tire rubber, gave interesting improvements respect to the no-fine control mixes, even though the developed resistance was lower respect to mixes containing mineral sand. This result was expected because of the cementing property of mineral sand. Although, the important result was that it was possible to use waste tire rubber in pervious concrete, with an appropriate dosage and granular dimension, for increasing the performance of traditional mix design, in order to achieve pavement materials more and more sustainable.

/pdf/laboratory-investigation-on-the-effects-of-natural-fine-2wk2m9llpw.pdf

Laboratory Investigation on the Effects of Natural Fine Aggregates and Recycled Waste Tire Rubber in Pervious Concrete to Develop More Sustainable Pavement Materials

Improving Pervious Concrete Pavements for Achieving More Sustainable Urban Roads

The enhancement of mechanical properties and long term performance of hot mix asphalt (HMA) should be considered as a goal in order to achieve a transport infrastructure really sustainable. However, this issue becomes a difficult task, if conventional HMA are used. In fact, performance of conventional HMA, usually presents poor long term performance and functional distresses related to high and low temperatures, which in turn implies higher maintenance costs and superior carbon footprints. To overcome this weaken, bitumen industry has been developing new polymer modifiers, additives to improve HMA behaviour. One of the techniques most used in developed countries to enhance HMA behaviour is the use of modified bitumen. Modifying the bitumen, and then producing modified HMA requires specific equipment and facilities that may be time-consuming, expensive and hard to manage. For instance, to warranty a successful modifying process, storage and handling of the modified bitumen are issues very complex to handle. On the other hand, producing a polymer modified HMA by adding polymers and additives directly during the bitumen/aggregate mixing process may offer very interesting advantages since the economical, production and sustainability standpoint. This paper aimed to determine the feasibility of the incorporation of fibres and plastomeric polymers into different types of HMA by means of the "dry process" (to add polymers during the mixing of aggregate and bitumen in the HMA plant) to produce polymer modified mixes. Thus, laboratory tests including Marshall Stability, Indirect Tensile Stiffness Modulus, repeated load test and Indirect Tensile Strength test were performed to assess the effect of the inclusion of fibres and plastomeric polymers on mechanical and volumetric properties of selected mixes. Results showed that the modification of bituminous mixtures following the "dry process" could be used to improve the performance and long term properties of HMA.

https://iopscience.iop.org/article/10.1088/1757-899X/245/2/022013/pdf

Gilberto Martínez Arguelles

Papers

Improving Pervious Concrete Pavements for Achieving More Sustainable Urban Roads

Improving Mechanical Properties of Hot Mix Asphalt Using Fibres and Polymers in Developing Countries