There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality.

Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

I and i

다중혈관 관상동맥 환자에서 y-문합을 이용하여 양쪽 내흉동맥만을 사용한 우회술의 조기 성적

Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

Phd by thesis

This article presents an overview of the developments in stainless steels made since the 1990s. Some of the new applications that involve the use of stainless steel are also introduced. A brief introduction to the various classes of stainless steels, their precipitate phases and the status quo of their production around the globe is given first. The advances in a variety of subject areas that have been made recently will then be presented. These recent advances include (1) new findings on the various precipitate phases (the new J phase, new orientation relationships, new phase diagram for the Fe–Cr system, etc.); (2) new suggestions for the prevention/mitigation of the different problems and new methods for their detection/measurement and (3) new techniques for surface/bulk property enhancement (such as laser shot peening, grain boundary engineering and grain refinement). Recent developments in topics like phase prediction, stacking fault energy, superplasticity, metadynamic recrystallisation and the calculation of mechanical properties are introduced, too. In the end of this article, several new applications that involve the use of stainless steels are presented. Some of these are the use of austenitic stainless steels for signature authentication (magnetic recording), the utilisation of the cryogenic magnetic transition of the sigma phase for hot spot detection (the Sigmaplugs), the new Pt-enhanced radiopaque stainless steel (PERSS) coronary stents and stainless steel stents that may be used for magnetic drug targeting. Besides recent developments in conventional stainless steels, those in the high-nitrogen, low-Ni (or Ni-free) varieties are also introduced. These recent developments include new methods for attaining very high nitrogen contents, new guidelines for alloy design, the merits/demerits associated with high nitrogen contents, etc.

Recent developments in stainless steels

http://digilib.its.ac.id/public/ITS-Undergraduate-10957-Paper.pdf

Carbon partitioning into austenite after martensite transformation

The quenching and partitioning or Q & P process concept has been developed over the past few years, as a heat-treatment to produce martensitic microstructures with carbon-enriched metastable retained austenite. The process involves partial martensite formation by controlled quenching, followed by a thermal treatment to allow carbon transport from the (supersaturated) martensite into the remaining austenite. Potential applications involve high strength where retained austenite may be beneficial for formability, fracture resistance, etc. The process may be applicable to production of steel sheet and plate products, as well as heat treated components produced from long product forgings, and even cast-iron. The concept has been studied in the authors' laboratories since about 2003 and a series of publications is available documenting much of the early work. More recent studies have focused on understanding mechanistic details, and other independent research groups are now also making advancements in this field.

Developments in the Quenching and Partitioning Process

Effect of Retained Austenite on Tensile Behavior of AHSS Revisited

Copper brazing response of some advanced high strength steel grades

The effects of microalloy precipitation and dissolution during direct slab production are explored relative to the position within a slab and alloy content. Niobium solute contents and precipitate fractions are quantified using electrochemical extraction and ICP-AES techniques.

/pdf/microalloy-precipitation-in-hot-charged-slabs-3wz9h2p2e2.pdf

Microalloy Precipitation in Hot Charged Slabs

In this work, the influence of selected alloying variations on Zn-assisted liquid metal embrittlement (LME) susceptibility of Zn-coated advanced high strength steels (AHSS) is investigated. Cold-rolled AHSS alloys of different carbon (C), manganese (Mn), silicon (Si), and aluminum (Al) concentrations were continuous-annealed to generate a third generation AHSS microstructure (composed of martensite and retained austenite) via quenching and partitioning. High temperature tension tests using simulated spot-weld thermomechanical cycles revealed no significant influence of C and Mn variations on the Zn-LME susceptibility of AHSS. On the other hand, Zn-LME susceptibility was strongly correlated with the Si content of AHSS. A direct comparison of the (reacted) coating microstructures of the Si-alloyed and Low-Si AHSS variants revealed that Si in the AHSS substrate suppresses Fe–Zn alloying reactions and retards the nucleation and growth of Fe-Zn intermetallic phases at the coating-substrate interface in these spot weld simulations. The suppressed intermetallic formation at elevated Si concentrations is consistent with phase equilibria considerations in the Fe-Zn-Si ternary system. In the context of Zn-assisted LME, therefore, Si is hypothesized to aggravate LME behavior by increasing the liquid Zn availability for embrittlement and promoting direct contact between liquid Zn and the AHSS steel substrate. 

John G. Speer

Papers

Developments in the Quenching and Partitioning Process

Effect of Retained Austenite on Tensile Behavior of AHSS Revisited

Copper brazing response of some advanced high strength steel grades

Microalloy Precipitation in Hot Charged Slabs

Influence of Selected Alloying Variations on Liquid Metal Embrittlement Susceptibility of Quenched and Partitioned Steels