The absorption and emission properties of transition metal (TM)-doped zinc chalcogenides have been investigated to understand their potential application as room-temperature, mid-infrared tunable laser media. Crystals of ZnS, ZnSe, and ZnTe, individually doped with Cr/sup 2+/, Co/sup 2+/, Ni/sup 2+/, or Fe/sup 2+/ have been evaluated. The absorption and emission properties are presented and discussed in terms of the energy levels from which they arise. The absorption spectra of the crystals studied exhibit strong bands between 1.4 and 2.0 /spl mu/m which overlap with the output of strained-layer InGaAs diodes. The room-temperature emission spectra reveal wide-band emissions from 2-3 /spl mu/m for Cr and from 2.8-4.0 /spl mu/m for Co, Cr luminesces strongly at room temperature; Co exhibits significant losses from nonradiative decay at temperatures above 200 K, and Ni and Fe only luminesce at low temperatures, Cr/sup 2+/ is estimated to have the highest quantum yield at room temperature among the media investigated with values of /spl sim/75-100%. Laser demonstrations of Cr:ZnS and Cr:ZnSe have been performed in a laser-pumped laser cavity with a Co:MgF/sub 2/ pump laser. The output of both lasers were determined to peak at wavelengths near 2.35 /spl mu/m, and both lasers demonstrated a maximum slope efficiency of approximately 20%. Based on these initial results, the Cr/sup 2+/ ion is predicted to be a highly favorable laser ion for the mid-IR when doped into the zinc chalcogenides; Co/sup 2+/ may also serve usefully, but laser demonstrations yet remain to be performed.

Transition metal-doped zinc chalcogenides: Spectroscopy and laser demonstration of a new class of gain media

Femtosecond-laser micromachining (also known as inscription or writing) has been developed as one of the most efficient techniques for direct three-dimensional microfabrication of transparent optical materials. In integrated photonics, by using direct writing of femtosecond/ultrafast laser pulses, optical waveguides can be produced in a wide variety of optical materials. With diverse parameters, the formed waveguides may possess different configurations. This paper focuses on crystalline dielectric materials, and is a review of the state-of-the-art in the fabrication, characterization and applications of femtosecond-laser micromachined waveguiding structures in optical crystals and ceramics. A brief outlook is presented by focusing on a few potential spotlights.

Optical waveguides in crystalline dielectric materials produced by femtosecond-laser micromachining

Abstract The emergence of silicon photonics over the past two decades has established silicon as a preferred substrate platform for photonic integration. While most silicon-based photonic components have so far been realized in the near-infrared (near-IR) telecommunication bands, the mid-infrared (mid-IR, 2–20-μm wavelength) band presents a significant growth opportunity for integrated photonics. In this review, we offer our perspective on the burgeoning field of mid-IR integrated photonics on silicon. A comprehensive survey on the state-of-the-art of key photonic devices such as waveguides, light sources, modulators, and detectors is presented. Furthermore, on-chip spectroscopic chemical sensing is quantitatively analyzed as an example of mid-IR photonic system integration based on these basic building blocks, and the constituent component choices are discussed and contrasted in the context of system performance and integration technologies.

/pdf/mid-infrared-integrated-photonics-on-silicon-a-perspective-31psns51w2.pdf

Mid-infrared integrated photonics on silicon: a perspective

This paper reviews the recent advancements achieved using ultrafast laser inscription (ULI) that highlight the cross-disciplinary potential of the technology. An overview of waveguide fabrication is provided and the three distinct types of waveguide cross-section architectures that have so far been fabricated in transparent dielectric materials are discussed. The paper focuses on two key emergent technologies driven by ULI processes. First, the recently developed photonic devices, such as compact mode-locked waveguide sources and novel mid-infrared waveguide lasers are discussed. Secondly, the phenomenon and applications of selective etching in developing ultrafast laser inscribed structures for compact lab-on-chip devices are elaborated. The review further discusses the conceivable future of ULI in impacting the aforementioned fields.

/pdf/ultrafast-laser-inscription-perspectives-on-future-l5ccc51m7v.pdf

Ultrafast laser inscription: perspectives on future integrated applications

The work described in this thesis details the development of a multicore fibre device that can be used to optically trap multiple cells and particles. The optical trapping of multiple cells at close proximity allows for cell-to-cell interactions to be studied. Current methods available for creating arrays of traps are free space optical systems that use diffractive optics, laser scanning techniques or the interference of multiple beams to create the multiple traps. A fully integrated, fibre optic based, multiple particles, optical trapping device could be used in non-optical research facilities such as biological laboratories to aid with their research into cellular processes. In order to create the multiple traps, the distal end of the multicore fibre needs to be modified to induce a lensing effect. The multicore fibre device presented in this thesis was lensed in a fusion splicer; this refracts the outputs from the four cores to a common point in the far field where interference fringes are formed. The initial investigation demonstrated one-dimensional interferometric optical trapping through coupling light into two of the diagonal cores of the lensed multicore fibre. This produced linear interference fringes approximately 250 ± 25 μm from the end of the fibre with a fringe spacing of 2 ± 0.3 μm. The linear interference fringes were used to optically trap polystyrene microspheres with diameters of 1.3 μm, 2 μm and 3 μm in the high intensity regions of the fringes. Coupling into all four cores using a diffractive optical element produced an array of intensity peaks across the interference pattern with high visibility fringes greater than 80 %. Each intensity peak, spaced 2.75 μm apart could trap a single particle in two dimensions. The optical trapping of multiple microspheres and Escherichia coli bacterial cells was demonstrated proving that the lensed multicore fibre has the potential to be used to trap cells in biological experiments. The active manipulation of trapped 2 μm microspheres was also demonstrated through the rotation of the input polarisation to the multicore fibre. Finally, work towards creating a “turn-key” optical trapping device was demonstrated through the fabrication of a fully integrated multicore fibre device using an ultrafast laser-inscribed fan-out to couple light into each core. Single mode operation of the device was demonstrated at 1550 nm, using a weaker lensed MCF device. The two dimensional trapping of 4.5 μm polystyrene microspheres was shown in an array of peaks spaced 11.2 μm apart at a distance of 400 ± 25 μm from the end of the fibre.

Integrated multicore fibre devices for optical trapping

We report the successful fabrication of a low-loss near-IR waveguide in polycrystalline ZnSe using ultrafast laser inscription. The waveguide, which was inscribed using the multiscan fabrication technique, supported a well-confined mode at 1.55μm. Propagation losses were characterized at 1.55μm using the Fabry–Perot technique and found to be 1.07dB·cm−1±0.03dB·cm−1.

Ultrafast laser inscription of near-infrared waveguides in polycrystalline ZnSe.

We report a Cr:ZnSe channel waveguide laser operating at 2486 nm. A maximum power output of 285 mW is achieved and slope efficiencies as high as 45% are demonstrated. Ultrafast laser inscription is used to fabricate the depressed cladding waveguide in a polycrystalline Cr:ZnSe sample. Waveguide structures are proposed as a compact and robust solution to the thermal lensing problem that has so far limited power scaling of transition metal doped II-VI lasers.

/pdf/efficient-mid-infrared-cr-znse-channel-waveguide-laser-3kak9ac6q7.pdf

Efficient mid-infrared Cr:ZnSe channel waveguide laser operating at 2486 nm.

We demonstrate a mid-infrared channel waveguide laser in Cr:ZnSe operating at 2573 nm The compact cavity has a total footprint of less than 3 cm2 and produces a maximum power output of 185 mW The depressed index cladding structures guide across the entire emission band of Cr:ZnSe, from 19 μm to 34 μm, indicating the viability of the device for integrated and robust continuously tunable mid-infrared sources

Compact mid-infrared Cr:ZnSe channel waveguide laser

A new (to our knowledge) ultrashort laser pulse irradiation regime that allows us to directly modify and increase the refractive index of rare earth doped YAG polycrystalline ceramics has been identified. Single-mode buried channel waveguides in both Ho:YAG and Er:YAG ceramics at the near-IR wavelengths of 1.55 μm and 1.95 μm are demonstrated by fabricating positive square step-index cores. Minimum propagation losses of 1.5 dB cm−1 at a 1.51 μm wavelength have been preliminarily obtained. Confocal microluminescence mapping reveals that the increased refractive index regions retain the near-IR spectral properties of Er3+ ions in the YAG crystalline matrix.

John R. Macdonald

Papers

Ultrafast laser inscription: perspectives on future integrated applications

Ultrafast laser inscription of near-infrared waveguides in polycrystalline ZnSe.

Efficient mid-infrared Cr:ZnSe channel waveguide laser operating at 2486 nm.

Compact mid-infrared Cr:ZnSe channel waveguide laser

Direct laser writing of near-IR step-index buried channel waveguides in rare earth doped YAG.