In this paper, an integrated double buck-boost (IDBB) converter is proposed as a high-power-factor offline power supply for power-LED lamps. The IDBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains, providing high power factor and good efficiency. In this paper, the IDBB converter is analyzed, and a design methodology is proposed. It is demonstrated that, with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures can be made as high as that of the solid-state lamp. A design example for a 70-W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.

Analysis and Design of the Integrated Double Buck–Boost Converter as a High-Power-Factor Driver for Power-LED Lamps

While LEDs enjoy relatively long lifetime up to 10 years, the lifetime of traditional LED drivers using electrolytic capacitor as storage element is limited to typically less than 5 years. In this paper, an ac/dc LED driver without electrolytic capacitor is studied. Compared with other methods to eliminate electrolytic capacitor, the proposed driver has the advantages of almost unity input power factor and constant output current for LEDs. The operation principle, detailed design procedure of the main circuit, and control strategy are presented. The feasibility of the proposed converter has been successfully verified by experiments.

Elimination of an Electrolytic Capacitor in AC/DC Light-Emitting Diode (LED) Driver With High Input Power Factor and Constant Output Current

Due to the high rise in luminous efficiency that HB-LEDs have experienced in the last recent years, many new applications have been researched. In this paper, a streetlight LED application will be covered, using the Integrated Buck-Flyback Converter developed in previous works, which performs power factor correction (PFC) from a universal ac source, as well as a control loop using the LM3524 IC, which allows PWM dimming operation mode. Firstly, the LED load will be linearized and modeled in order to calculate the IBFC topology properly. Afterwards, the converter will be calculated, presenting the one built in the lab. Secondly, the converter will be modeled in order to build the closed loop system, modeling the current sensor as well in order to develop an adequate controller. Finally, experimental results obtained from the lab tests will be presented.

A Universal-Input Single-Stage High-Power-Factor Power Supply for HB-LEDs Based on Integrated Buck-Flyback Converter

Based on a survey on over 1400 commercial LED drivers and a literature review, a range of LED driver topologies are classified according to their applications, power ratings, performance and their energy storage and regulatory requirements. Both passive and active LED drivers are included in the review and their advantages and disadvantages are discussed. This paper also presents an overall view on the technical and cost aspects of the LED technology, which is useful to both researchers and engineers in the lighting industry. Some general guidelines for selecting driver topologies are included to aid design engineers to make appropriate choices.

A Survey, Classification, and Critical Review of Light-Emitting Diode Drivers

The high-brightness white-light-emitting diode (LED) has attracted a lot of attention for its high efficacy, simple to drive, environmentally friendly, long lifespan, and compact size. The power supply for LED also requires long life, while maintaining high efficiency, high power factor, and low cost. However, a typical power supply design employs an electrolytic capacitor as the storage capacitor, which is not only bulky, but also with a short lifespan, thus hampering performance improvement of the entire LED lighting system. In this paper, a novel power factor correction (PFC) topology is proposed by inserting the valley-fill circuit in the single-ended primary inductance converter (SEPIC)-derived converter, which can reduce the voltage stress of the storage capacitor and output diode under the same power factor condition. This valley-fill SEPIC-derived topology is, then, proposed for LED lighting applications. By allowing a relatively large voltage ripple in the PFC design and operating in the discontinuous conduction mode (DCM), the proposed PFC topology is able to eliminate the electrolytic capacitor, while maintaining high power factor and high efficiency. Under the electrolytic capacitor-less condition, the proposed PFC circuit can reduce the capacitance of the storage capacitor to half for the same power factor and output voltage ripple as comparing to its original circuit. To further increase the efficiency of LED driver proposal, a twin-bus buck converter is introduced and employed as the second-stage current regulator with the PWM dimming function. The basic operating principle and analysis will be described in detail. A 50-W prototype has been built and tested in the laboratory, and the experimental results under universal input-voltage operation are presented to verify the effectiveness and advantages of the proposal.

A Novel Valley-Fill SEPIC-Derived Power Supply Without Electrolytic Capacitor for LED Lighting Application

This paper presents a dimmable light-emitting diode (LED) driver with adaptive feedback control for low-power lighting applications. An improved pulsewidth modulation dimming technique is studied for regulating the LED current and brightness. Under universal input voltage operation, high efficiency and high power factor can be achieved by a coupled inductor single-ended primary inductance converter power factor correction (PFC) converter with a simple commercial transition-mode PFC controller. The operation principles and design considerations of the studied LED driver are analyzed and discussed. A laboratory prototype is also designed and tested to verify the feasibility.

/pdf/a-high-efficiency-dimmable-led-driver-for-low-power-lighting-35b376meg0.pdf

A High-Efficiency Dimmable LED Driver for Low-Power Lighting Applications

An indirect control variable for improving the control-to-output characteristics of a Pulse Width Modulation (PWM) buck-boost converter is introduced in this letter. The voltage gain and the small-signal model of the buck-boost converter are reviewed. The actual voltage command at one input of the PWM comparator is from the proposed indirect control variable and the peak value of the high-frequency PWM carrier. The resulted voltage gain function appears proportional to this indirect control command. Also the dependence of the DC gain of the control-to-output transfer function on the duty cycle is eliminated. Experimental results conform well to the theoretical analysis. Copyright © 2010 John Wiley & Sons, Ltd.

Jun-Ting Chen

Papers

A High-Efficiency Dimmable LED Driver for Low-Power Lighting Applications

Improved control-to-output characteristics of a PWM buck-boost converter