Fuel cells have the potential to become an important energy conversion technology. Research efforts directed toward the widespread commercialization of fuel cells have accelerated in light of ongoing efforts to develop a hydrogen-based energy economy to reduce dependence on foreign oil and decrease pollution. Proton exchange membrane (also termed “polymer electrolyte membrane”) (PEM) fuel cells employing a solid polymer electrolyte to separate the fuel from the oxidant were first deployed in the Gemini space program in the early 1960s using cells that were extremely expensive and had short lifetimes due to the oxidative degradation of their sulfonated polystyrene-divinylbenzene copolymer membranes. These cells were considered too costly and short-lived for real-world applications. The commercialization of Nafion by DuPont in the late 1960s helped to demonstrate the potential interest in terrestrial applications for fuel cells, although its major focus was in chloroalkali processes. PEM fuel cells are being developed for three main applications: automotive, stationary, and portable power. Each of these applications has its unique operating conditions and material requirements. Common themes critical to all high performance proton exchange membranes include (1) high protonic conductivity, (2) low electronic conductivity, (3) low permeability to fuel and oxidant, (4) low water transport through diffusion and electro-osmosis, (5) oxidative and hydrolytic stability, (6) good mechanical properties in both the dry and hydrated states, (7) cost, and (8) capability for fabrication into membrane electrode assemblies (MEAs). Nearly all existing membrane materials for PEM fuel cells rely on absorbed water and its interaction with acid groups to produce protonic conductivity. Due to the large fraction of absorbed water in the membrane, both mechanical properties and water transport become key issues. Devising systems that can conduct protons with little or no water is perhaps the greatest challenge for new membrane materials. Specifically, for automotive applications the U.S. Department of Energy has currently established a guideline of 120 °C and 50% relative humidity as target operating conditions, and a goal of 0.1 S/cm for the protonic conductivity of the membrane. New membranes that have significantly reduced methanol permeability and water transport (through diffusion and electro-osmotic drag) are required for portable power oriented direct methanol fuel cells (DMFCs), where a liquid methanol fuel highly diluted in water is used at generally <90 °C as the source of protons. Unreacted methanol at the anode can diffuse through the membrane and react at the cathode, lowering the voltage efficiency of the cell and reducing the system’s fuel efficiency. The methanol is usually delivered to the anode as a dilute, for example, 1 M (or less), solution (3.2 wt %), and relatively thick Nafion 117 (1100 EW, 7 mil ∼ 178 μm thick) is used to reduce methanol crossover. The dilute methanol feed increases the system’s complexity and reduces the energy density of the fuel, while the thick Nafion membrane increases the resistive losses of the cell, especially when compared to the thinner membranes that are used in hydrogen/air systems. The presence of excessive amounts of water at the cathode through diffusion and electro-osmosis * To whom correspondence should be addressed. E-mail: jmcgrath@vt.edu. † Sandia National Laboratory. ‡ Case Western Reserve University. § Los Alamos National Laboratory. | Virginia Polytechnic Institute and State University. 4587 Chem. Rev. 2004, 104, 4587−4612

Alternative Polymer Systems for Proton Exchange Membranes (PEMs)

1. Introduction 46372. Theoretical Methodologies and Simulation Tools 46402.1. Ab Initio Quantum Chemistry 46412.2. Molecular Dynamics 46422.2.1. Classical Molecular Dynamics and MonteCarlo Simulations46432.2.2. Empirical Valence Bond Models 46442.2.3. Ab Initio Molecular Dynamics (AIMD) 46452.3. Poisson−Boltzmann Theory 46452.4. Nonequilibrium Statistical Mechanical IonTransport Modeling46462.5. Dielectric Saturation 46473. Transport Mechanisms 46483.1. Proton Conduction Mechanisms 46483.1.1. Homogeneous Media 46483.1.2. Heterogeneous Systems (ConfinementEffects)46553.2. Mechanisms of Parasitic Transport 46613.2.1. Solvated Acidic Polymers 46613.2.2. Oxides 46654. Phenomenology of Transport inProton-Conducting Materials for Fuel-CellApplications46664.1. Hydrated Acidic Polymers 46664.2. PBI−H

/pdf/transport-in-proton-conductors-for-fuel-cell-applications-3gvrtpo4jv.pdf

Transport in proton conductors for fuel-cell applications: simulations, elementary reactions, and phenomenology.

Review of the proton exchange membranes for fuel cell applications

The state-of-the-art of polymer electrolyte membrane fuel cell (PEMFC) technology is based on perfluorosulfonic acid (PFSA) polymer membranes operating at a typical temperature of 80 °C. Some of the key issues and shortcomings of the PFSA-based PEMFC technology are briefly discussed. These include water management, CO poisoning, hydrogen, reformate and methanol as fuels, cooling, and heat recovery. As a means to solve these shortcomings, high-temperature polymer electrolyte membranes for operation above 100 °C are under active development. This treatise is devoted to a review of the area encompassing modified PFSA membranes, alternative sulfonated polymer and their composite membranes, and acid−base complex membranes. PFSA membranes have been modified by swelling with nonvolatile solvents and preparing composites with hydrophilic oxides and solid proton conductors. DMFC and H2/O2(air) cells based on modified PFSA membranes have been successfully operated at temperatures up to 120 °C under ambient pressure...

/pdf/approaches-and-recent-development-of-polymer-electrolyte-1glbhokzz9.pdf

Approaches and Recent Development of Polymer Electrolyte Membranes for Fuel Cells Operating above 100 °C

Review and analysis of PEM fuel cell design and manufacturing

http://www.engr.uconn.edu/~jmfent/membrane%20review%201.pdf

K Sanui

Papers

Proton-conducting polymer electrolyte membranes based on hydrocarbon polymers