To progress from the laboratory to commercial applications, it will be necessary to develop industrially scalable methods to produce large quantities of defect-free graphene. Here we show that high-shear mixing of graphite in suitable stabilizing liquids results in large-scale exfoliation to give dispersions of graphene nanosheets. X-ray photoelectron spectroscopy and Raman spectroscopy show the exfoliated flakes to be unoxidized and free of basal-plane defects. We have developed a simple model that shows exfoliation to occur once the local shear rate exceeds 10(4) s(-1). By fully characterizing the scaling behaviour of the graphene production rate, we show that exfoliation can be achieved in liquid volumes from hundreds of millilitres up to hundreds of litres and beyond. The graphene produced by this method performs well in applications from composites to conductive coatings. This method can be applied to exfoliate BN, MoS2 and a range of other layered crystals.

/pdf/scalable-production-of-large-quantities-of-defect-free-few-2ehr40fw5v.pdf

Scalable production of large quantities of defect-free few-layer graphene by shear exfoliation in liquids

https://cyberleninka.org/article/n/768408.pdf

Mechanical properties of graphene and graphene-based nanocomposites

High-energy yarn supercapacitors are desirable for safe and wearable electronics. Here, Kou et al. use a coaxial wet-spinning assembly method to fabricate core-sheath fibres of polymer-wrapped carbon nanomaterials and demonstrate high-performance supercapacitor applications.

/pdf/coaxial-wet-spun-yarn-supercapacitors-for-high-energy-1cddlir9n4.pdf

Coaxial wet-spun yarn supercapacitors for high-energy density and safe wearable electronics

Energy storage devices that can deliver high powers have many applications, including hybrid vehicles and renewable energy. Much research has focused on increasing the power output of lithium batteries by reducing lithium-ion diffusion distances, but outputs remain far below those of electrochemical capacitors and below the levels required for many applications. Here, we report an alternative approach based on the redox reactions of functional groups on the surfaces of carbon nanotubes. Layer-by-layer techniques are used to assemble an electrode that consists of additive-free, densely packed and functionalized multiwalled carbon nanotubes. The electrode, which is several micrometres thick, can store lithium up to a reversible gravimetric capacity of approximately 200 mA h g(-1)(electrode) while also delivering 100 kW kg(electrode)(-1) of power and providing lifetimes in excess of thousands of cycles, both of which are comparable to electrochemical capacitor electrodes. A device using the nanotube electrode as the positive electrode and lithium titanium oxide as a negative electrode had a gravimetric energy approximately 5 times higher than conventional electrochemical capacitors and power delivery approximately 10 times higher than conventional lithium-ion batteries.

High-Power Lithium Batteries from Functionalized Carbon Nanotube Electrodes

Polyurethanes (PUs) are a class of versatile materials with great potential for use in different applications, especially based on their structure–property relationships. Their specific mechanical, physical, biological, and chemical properties are attracting significant research attention to tailoring PUs for use in different applications. Enhancement of the properties and performance of PU-based materials may be achieved through changes to the production process or the raw materials used in their fabrication or via the use of advanced characterization techniques. Clearly, modification of the raw materials and production process through proper methods can produce PUs that are suitable for varied specific applications. The present study aims to shed light on the chemistry, types, and synthesis of different kinds of PUs. Some of the important research studies relating to PUs, including their synthesis method, characterization techniques, and research findings, are comprehensively discussed. Herein, recent advances in new types of PUs and their synthesis for various applications are also presented. Furthermore, information is provided on the environmental friendliness of the PUs, with a specific emphasis on their recyclability and recoverability.

https://ir.unikl.edu.my/jspui/bitstream/123456789/15237/1/Polyurethane%20types%2c%20synthesis%20and%20applications%20%e2%80%93%20a%20review.pdf

Polyurethane types, synthesis and applications – a review

This paper provides an insight into some developments in flame retardants for different polymeric materials in China, primarily based on the publications that have appeared in the last 15 years. It focuses on the following aspects: halogen-containing flame retardants, inorganic flame retardants (e.g. metal oxides and hydroxides, silicon-containing materials, ammonium polyphosphate, red phosphorus, and expandable graphite), and organic flame retardants (e.g. aliphatic and aromatic phosphonates, nitrogen-containing organics, and multi-element organics). The inherently flame-retardant polymer systems are also reviewed. The exploration of the novel flame retardants and flame-retardant systems provides a powerful basis for the construction of flame-retardant technologies and industrial applications in China. Copyright © 2009 John Wiley & Sons, Ltd.

A review on flame retardant technology in China. Part I: development of flame retardants

Controlling the interface interaction of polymer/filler is essential for the fabrication of high-performance polymer composites. In this work, a core–shell structured hybrid (SiO2–GO) was prepared and introduced into an epoxy polymer matrix as a new filler. The incorporation of the hybrid optimized the modulus, strength and fracture toughness of the composites simultaneously. The ultrathin GO shells coated on silica surfaces were regarded as the main reason for the enhancement. Located at the silica-epoxy interface, GO served as an unconventional coupling agent of the silica filler, which effectively enhanced the interfacial interaction of the epoxy/SiO2–GO composites, and thus greatly improved the mechanical properties of the epoxy resin. We believe this new and effective approach that using GO as a novel fillers surface modifier may open a novel interface design strategy for developing high performance composites.

Enhanced epoxy/silica composites mechanical properties by introducing graphene oxide to the interface.

We found in our previous study that ethylenediamine- or ethanolamine-modified ammonium polyphosphates could be used alone as an intumescent flame retardant for polypropylene (PP), but their flame-retardant efficiency was not very high. In this present work, a novel highly-efficient mono-component polymeric intumescent flame retardant, piperazine-modified ammonium polyphosphate (PA-APP) was prepared. The oxygen index value of PP containing 22 wt % of PA-APP reached 31.2%, which increased by 58.4% compared with that of PP with equal amount of APP, and the vertical burning test (UL-94) could pass V-0 rating. Cone calorimeter (CC) results indicated that PP/PA-APP composite exhibited superior performance compared with PP/APP composite. For PP containing 25 wt % of PA-APP, fire growth rate (FGR) and smoke production rate (SPR) peak were reduced by 86.4% and 78.2%, respectively, compared with PP blended with 25 wt % APP. The relevant flame-retardant mechanism of PA-APP was investigated by Fourier transform infra...

An Efficient Mono-Component Polymeric Intumescent Flame Retardant for Polypropylene: Preparation and Application

Ammonium polyphosphate (APP) is not an efficient flame retardant for polypropylene (PP) when it is used alone. In order to improve its flame-retardant efficiency, ethanolamine (ETA) was used to chemically modify APP via ion exchange reaction. The resulting ethanolamine-modified ammonium polyphosphate (ETA-APP) was alone applied to flame retard PP, the limiting oxygen index (LOI) value could reach 35.0% and the vertical burning test (UL-94) could pass the V-0 rating at a loading of 35 wt% ETA-APP. Moreover, cone calorimeter (CC) test results showed that the heat release rate (HRR), the total heat release (THR), the mass loss rate (MLR), the smoke production rate (SPR) and the total smoke production (TSP) of PP/35 wt% ETA-APP composite largely decreased, for example, by 77.2%, 88.5% and 77.9% for THR, TSP and the fire growth rate (FGR), respectively, compared with PP containing an equal amount of APP. In addition, the residual char of PP/35 wt% ETA-APP increased by 195.6% compared with that of PP/35 wt% APP. Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) were used to analyze the flame retardant mechanism of ETA-APP. It was confirmed that the formation of P–O–C and P–N–C structures, resulting from the incorporation of ETA could greatly improve the stability of intumescent char layer and consequently lead to the much better flame retardancy of ETA-APP than that of unmodified APP. Experimental results demonstrated that the prepared ETA-APP acted not only as the acid source and blowing source as efficient as unmodified APP, but also as an excellent charring agent beyond the unmodified APP.

Ammonium polyphosphate chemically-modified with ethanolamine as an efficient intumescent flame retardant for polypropylene

A novel multifunctional organic–inorganic hybrid was designed and prepared based on ammonium polyphosphate (APP) by cation exchange with diethylenetriamine (DETA), abbreviated as DETA-APP. Then DETA-APP was used as flame-retardant curing agent for epoxy resin (EP). Curing behavior, including the curing kinetic parameters, was investigated by differential scanning calorimetry (DSC) and X-ray photoelectron spectroscopy (XPS). The flame retardance and burning behavior of DETA-APP cured EP were also evaluated. The limiting oxygen index (LOI) value of DETA-APP/EP was enhanced to 30.5% with only 15 wt % of DETA-APP incorporated; and the UL-94 V-0 rating could be easily passed through with only 10 wt % of the hybrid. Compared with DETA/EP, the peak-heat release rate (PHRR), total heat release (THR), total smoke production (TSP), and peak-smoke production release (SPR) of DETA-APP/EP (15 wt % addition), obtained from cone calorimetry, were dropped by 68.3, 79.3, 79.0, and 30.0%, respectively, suggesting excellent...

Li Chen

Papers

A review on flame retardant technology in China. Part I: development of flame retardants

Enhanced epoxy/silica composites mechanical properties by introducing graphene oxide to the interface.

An Efficient Mono-Component Polymeric Intumescent Flame Retardant for Polypropylene: Preparation and Application

Ammonium polyphosphate chemically-modified with ethanolamine as an efficient intumescent flame retardant for polypropylene

Novel Multifunctional Organic–Inorganic Hybrid Curing Agent with High Flame-Retardant Efficiency for Epoxy Resin