Numerical investigation on the unsteady characteristics of reactor coolant pumps with non-uniform inflow

Study on the complete rotational characteristic of coolant pump in the gas-liquid two-phase operating condition

Effects of rotating speed on the unsteady pressure pulsation of reactor coolant pumps with steam-generator simulator

Vertical inline pump is a single-stage single-suction centrifugal pump with a bent pipe before the impeller, which is usually used where installation space is a constraint. In this paper, with three objective functions of efficiencies at 0.5 Qd, 1.0 Qd, and 1.5 Qd, a multi-objective optimization on the inlet pipe of a vertical inline pump was proposed based on genetic algorithm with artificial neural network (ANN). In order to describe the shape of inlet pipe, the fifth-order and third-order Bezier curves were adopted to fit the mid curve and the trend of parameters of cross sections, respectively. Considering the real installation and computation complexity, 11 variables were finally used in this optimization. Latin hypercube sampling (LHS) was adopted to generate 149 sample cases, which were solved by CFD code ANSYS cfx 18.0. The calculation results and design variables were utilized to train ANNs, and these surrogate models were solved for the optimum design using multi-objective genetic algorithm (MOGA). The results showed the following: (1) There was a great agreement between numerical results and experimental results; (2) The ANNs could accurately fit the objective functions and variables. The maximum deviations of efficiencies at 0.5 Qd, 1.0 Qd, and 1.5 Qd, between predicted values and computational values, were 1.94%, 2.35%, and 0.40%; (3) The shape of inlet pipe has great influence on the efficiency at part-load and design conditions while the influence is slight at overload condition; (4) Three optimized cases were selected and the maximum increase of the efficiency at 0.5 Qd, 1.0 Qd, and 1.5 Qd was 4.96%, 2.45, and 0.79%, respectively; and (5) The velocity distributions of outflow in the inlet pipe of the three optimized cases were more uniform than the original one.

Multi-Objective Shape Optimization on the Inlet Pipe of a Vertical Inline Pump

A multiobjective optimization technique based on the computational fluid dynamics (CFD) simulations and the orthogonal test is proposed to reduce the pressure pulsation in this paper. Three levels of four well-known performance factors L9 (34) were considered in the orthogonal test scheme: the number of blades, the blade setting angle, the hub ratio, and the distance between the blade and the guide vane. The evaluation indexes corresponded to the head, efficiency, shaft power, and pressure pulsation, respectively. An optimal configuration A2B1C2D3 was obtained by comprehensive frequency analysis method, after intuitive and range analysis. In comparison with the nonoptimized model, the new design’s head and efficiency increased by 17.8% and 4.26%, whilst the shaft power and the pressure pulsation coefficient reduced by 1.22% and 11%, respectively. Experiments conducted on the optimized pump were consistent with the CFD model. Six different rotational speed conditions in the optimal operating points were numerically calculated in order to explore the internal hydraulic characteristics of the optimized axial flow pump. It is verified that the comprehensive frequency analysis method based on the orthogonal test approach is effective for the multiobjective optimization of the axial flow pump.

/pdf/multiobjective-optimization-design-and-experimental-7zv8swmfv1.pdf

Multiobjective Optimization Design and Experimental Investigation on the Axial Flow Pump with Orthogonal Test Approach

The diffuser of a reactor coolant pump was optimized using an orthogonal approach with numerical simulation to improve the pump hydraulic performance. Steady simulation was conducted by solving Reynolds-averaged Naiver-Stokes equations with the SST k-ω turbulence model using CFX code. The influence of the diffuser geometric parameters, namely, S, φ, α
 4, b
 4, δ
 2, R
 t and R
 4, on the pump performance were determined. L18 (37) orthogonal table was chosen for the optimization process. Best indicators were determined, and range analysis of energy losses, head, and efficiency at the rated condition was performed. Optimal parameters of the diffuser were S = 490 mm, φ = 36°, α
 4 = 30°, b
 4 = 200 mm, δ
 2 = 20 mm, R
 t = 5 mm and R
 4 = 565 mm. The final design was experimentally tested. Simulation results showed more remarkable performance than the experimental result. However, the numerical predictions and experimental results were consistent, validating the design procedure. Loading of the impeller and diffuser blades was analyzed to investigate the direct impact on the hydrodynamic flow field. The head was 14.74 m, efficiency was 79.6 %, and efficiency of the prototype pump was 83.3 % when the model pump functioned at the rated conditions. Optimization results showed that efficiency and head were improved at the design condition.

Li Tianbin

Papers

Numerical and experimental investigation on the diffuser optimization of a reactor coolant pump with orthogonal test approach