다중혈관 관상동맥 환자에서 y-문합을 이용하여 양쪽 내흉동맥만을 사용한 우회술의 조기 성적

The many different techniques for maximum power point tracking of photovoltaic (PV) arrays are discussed. The techniques are taken from the literature dating back to the earliest methods. It is shown that at least 19 distinct methods have been introduced in the literature, with many variations on implementation. This paper should serve as a convenient reference for future work in PV power generation.

/pdf/comparison-of-photovoltaic-array-maximum-power-point-2nci76j6n4.pdf

Comparison of Photovoltaic Array Maximum Power Point Tracking Techniques

http://ieeexplore.ieee.org/iel5/5610941/5624686/05624745.pdf

Power electronics

Review of the maximum power point tracking algorithms for stand-alone photovoltaic systems

This paper proposes a hybrid ac/dc micro grid to reduce the processes of multiple dc-ac-dc or ac-dc-ac conversions in an individual ac or dc grid. The hybrid grid consists of both ac and dc networks connected together by multi-bidirectional converters. AC sources and loads are connected to the ac network whereas dc sources and loads are tied to the dc network. Energy storage systems can be connected to dc or ac links. The proposed hybrid grid can operate in a grid-tied or autonomous mode. The coordination control algorithms are proposed for smooth power transfer between ac and dc links and for stable system operation under various generation and load conditions. Uncertainty and intermittent characteristics of wind speed, solar irradiation level, ambient temperature, and load are also considered in system control and operation. A small hybrid grid has been modeled and simulated using the Simulink in the MATLAB. The simulation results show that the system can maintain stable operation under the proposed coordination control schemes when the grid is switched from one operating condition to another.

A Hybrid AC/DC Microgrid and Its Coordination Control

Overvoltages in low voltage (LV) feeders with high penetration of photovoltaics (PV) are usually prevented by limiting the feeder's PV capacity to very conservative values, even if the critical periods rarely occur. This paper discusses the use of droop-based active power curtailment techniques for overvoltage prevention in radial LV feeders as a means for increasing the installed PV capacity and energy yield. Two schemes are proposed and tested in a typical 240-V/75-kVA Canadian suburban distribution feeder with 12 houses with roof-top PV systems. In the first scheme, all PV inverters have the same droop coefficients. In the second, the droop coefficients are different so as to share the total active power curtailed among all PV inverters/houses. Simulation results demonstrate the effectiveness of the proposed schemes and that the option of sharing the power curtailment among all customers comes at the cost of an overall higher amount of power curtailed.

Coordinated Active Power Curtailment of Grid Connected PV Inverters for Overvoltage Prevention

Islanding detection is a mandatory feature for grid-connected inverters. The effectiveness of passive islanding detection methods (IDMs) is usually demonstrated by means of nondetection zones (NDZs) represented in a power mismatch space (/spl Delta/P versus /spl Delta/Q). Active frequency drifting IDMs have been shown to provide improved performance but their theoretical NDZ cannot be described in the /spl Delta/P versus /spl Delta/Q space for a general RLC load. This paper shows that a load parameter space based on the values of the quality factor and resonant frequency of the local load (Q/sub f/ versus f/sub 0/) can be used in these cases. It employs a single curve to represent the NDZ of frequency drifting IDMs for any RLC loads. Equations that represent NDZs of three common active IDMs in the Q/sub f/ versus f/sub 0/ load parameter space are derived and it is shown that the slip mode frequency shift and the Sandia frequency shift IDMs can be designed to guarantee islanding detection for equivalent RLC loads with a quality factor smaller than a design value. The accuracy of the NDZs is verified with simulation and experimental results.

Performance assessment of active frequency drifting islanding detection methods

This paper investigates the use of a virtual synchronous machine (VSM) to support dynamic frequency control in a diesel-hybrid autonomous power system. The proposed VSM entails controlling the grid-interface converter of an energy storage system (ESS) to emulate the inertial response and the damping power of a synchronous generator. In addition, self-tuning algorithms are used to continuously search for optimal parameters during the operation of the VSM in order to minimize the amplitude and rate of change of the frequency variations and the power flow through the ESS. The performances of the proposed self-tuning (ST)-VSM and the constant parameters (CP)-VSM were evaluated by comparing their inertial responses and their damping powers for different scenarios of load variations. For the simulated cases, the ST-VSM achieved a similar performance to that of the CP-VSM, while reducing the power flow through the ESS in up to 58%. Moreover, in all the simulated scenarios, the ST-VSM was found to be more efficient than the CP-VSM in attenuating frequency variations, i.e., it used less energy per Hertz reduced.

Self-Tuning Virtual Synchronous Machine: A Control Strategy for Energy Storage Systems to Support Dynamic Frequency Control

This paper discusses a new implementation of a perturbation and observation (P&O) maximum power point tracking (MPPT) algorithm that can mitigate/reduce the main drawbacks commonly related to the P&O method. This is achieved with peak current control, small perturbation values and sampling of instantaneous values, instead of averaged, to speed up the system response and reduce the oscillations around the maximum power point (MPP). The number of samples per switching cycle, type (synchronized/ unsynchronized) and ideal instant for sampling (maximum or minimum current) are investigated in order to obtain fast calculation of the direction of the next perturbation. Experimental results with the proposed control scheme implemented in a DSP are presented.

An improved perturbation and observation maximum power point tracking algorithm for PV arrays

This paper presents an alternative way for the current regulation of single-phase voltage-source dc-ac converters in direct-quadrature (dq) synchronous reference frames. In a dq reference frame, ac (time varying) quantities appear as dc (time invariant) ones, allowing the controller to be designed the same as dc-dc converters, presenting infinite control gain at the steady-state operating point to achieve zero steady-state error. The common approach is to create a set of imaginary quantities orthogonal to those of the real single-phase system so as to obtain dc quantities by means of a stationary-frame to rotating-frame transformation. The orthogonal imaginary quantities in common approaches are obtained by phase shifting the real components by a quarter of the fundamental period. The introduction of such delay in the system deteriorates the dynamic response, which becomes slower and oscillatory. In the proposed approach of this paper, the orthogonal quantities are generated by an imaginary system called fictive axis, which runs concurrently with the real one. The proposed approach, which is referred to as fictive-axis emulation, effectively improves the poor dynamics of the conventional approaches while not adding excessive complexity to the controller structure.

Luiz A. C. Lopes

Papers

Coordinated Active Power Curtailment of Grid Connected PV Inverters for Overvoltage Prevention

Performance assessment of active frequency drifting islanding detection methods

Self-Tuning Virtual Synchronous Machine: A Control Strategy for Energy Storage Systems to Support Dynamic Frequency Control

An improved perturbation and observation maximum power point tracking algorithm for PV arrays

Vector Control of Single-Phase Voltage-Source Converters Based on Fictive-Axis Emulation