A method is presented in which fracture mechanics is introduced into finite element analysis by means of a model where stresses are assumed to act across a crack as long as it is narrowly opened. This assumption may be regarded as a way of expressing the energy adsorption GC in the energy balance approach, but it is also in agreement with results of tension tests. As a demonstration the method has been applied to the bending of an unreinforced beam, which has led to an explanation of the difference between bending strength and tensile strength, and of the variation in bending strength with beam depth.

Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements

A fracture theory for a heterogenous aggregate material which exhibits a gradual strain-softening due to microcracking and contains aggregate pieces that are not necessarily small compared to structural dimensions is developed. Only Mode I is considered. The fracture is modeled as a blunt smeard crack band, which is justified by the random nature of the microstructure. Simple triaxial stress-strain relations which model the strain-softening and describe the effect of gradual microcracking in the crack band are derived. It is shown that it is easier to use compliance rather than stiffness matrices and that it suffices to adjust a single diagonal term of the complicance matrix. The limiting case of this matrix for complete (continuous) cracking is shown to be identical to the inverse of the well-known stiffness matrix for a perfectly cracked material. The material fracture properties are characterized by only three parameters—fracture energy, uniaxial strength limit and width of the crack band (fracture process zone), while the strain-softening modulus is a function of these parameters. A method of determining the fracture energy from measured complete stres-strain relations is also given. Triaxial stress effects on fracture can be taken into account. The theory is verified by comparisons with numerous experimental data from the literature. Satisfactory fits of maximum load data as well as resistance curves are achieved and values of the three material parameters involved, namely the fracture energy, the strength, and the width of crack band front, are determined from test data. The optimum value of the latter width is found to be about 3 aggregate sizes, which is also justified as the minimum acceptable for a homogeneous continuum modeling. The method of implementing the theory in a finite element code is also indicated, and rules for achieving objectivity of results with regard to the analyst's choice of element size are given. Finally, a simple formula is derived to predict from the tensile strength and aggregate size the fracture energy, as well as the strain-softening modulus. A statistical analysis of the errors reveals a drastic improvement compared to the linear fracture theory as well as the strength theory. The applicability of fracture mechanics to concrete is thus solidly established.

/pdf/crack-band-theory-for-fracture-of-concrete-4hm1hrkirl.pdf

Crack band theory for fracture of concrete

A calculation model (the Fictitious Crack Model), based on fracture mechanics and the finite element method, 1s presented. In the model the fracture zone in front of a crack is represented by a fictitious crack that 1s able to transfer stress. The stress transferring capability of the fictitious crack normally decreases when the crack width increases. The applicability of linear elastic fracture mechanics to concrete and similar materials is analysed by use of the Fictitious Crack Model. It" Is found that linear elastic fracture mechanics 1s too dependent on, among other things, specimen dimensions to be useful as a fracture approach, unless the dimensions, for concrete structures, are in order of meters. The usefulness of the J-integral, the COD-approach and the R-curve analysis is also found to be very limited where cementitious materials are concerned. The complete tensile stress-strain curve is introduced as a fracture mechanical parameter. The curve can be approximatively determined if the tensile strength, the Young's modius and the fracture energy are known. Su1table~lest methods Tor determining" TRise~~/'Voerties are presented and test results are reported for a number of concrete qua! » a. A new tyr * very stiff tensile testing machine Is presented by which it is possible to carry r . itable tensile tests on concrete. The complete tensile stress-strain curves h •«• feen determined for a number of concrete qualities. The thesi' overs a complete system for analysing crack propagation in concrete as it Include* -ealistic material model, a functional calculation model and methods for determiv" «/ the material properties necessary for the calculations. Therefore this work oi r t to be of use as a base for further studies of the fracture process of concrete < i similar materials.

Crack growth and development of fracture zones in plain concrete and similar materials

Truss model approaches and related theories for the design of reinforced concrete members to resist shear are presented. Realistic models for the design of deep beams, corbels, and other nonstandar...

M. S. Marathe

Papers

Microcracking and stress-strain curves for concrete in tension