We report measurements of transverse beam halo in mismatched proton beams in a 52-quadrupole FODO transport channel following the 6.7-MeV LEDA RFQ. Beam profiles in both transverse planes are measured using beam-profile diagnostic devices that consist of a movable carbon filament for measurement of the dense beam core, and scraper plates for the halo measurement. The gradients of the first four quadrupoles can be independently adjusted to mismatch the RFQ output beam into the beam-transport channel.

/pdf/experimental-study-of-proton-beam-halo-induced-by-beam-5cqazlsc3q.pdf

Experimental study of proton-beam halo induced by beam mismatch in LEDA

The Linac4, now being developed at CERN, will provide 160-MeV H - beams of high intensity N = 2 × 10 14 ions s - 1 . Before this beam can be injected into the CERN Proton Synchrotron Booster or future Superconducting Proton Linac for further acceleration, some sequences of 500-ps-long micro-bunches must be removed from it, using a beam chopper. These bunches, if left in the beam, would fall outside the longitudinal acceptance of the accelerators and make them radioactive. We developed a monitor to measure the time structure and spatial profile of this chopped beam, with respective resolutions Δ t ∼ 1 ns and Δ x ∼ 2 mm . Its large active area 40 mm × 40 mm and dynamic range also allows investigations of beam halos. The ion beam first struck a carbon foil, and secondary electrons emerging from the foil were accelerated by a series of parallel grid electrodes. These electrons struck a phosphor screen, and the resulting image of the scintillation light was guided to a thermoelectrically cooled, charge-coupled device camera. The time resolution was attained by applying high-voltage pulses of sub-nanosecond rise and fall times to the grids. The monitor has been tested with 700-ps-long UV laser pulses, and a 3-MeV proton beam. Its response over a wide range of beam intensities between N e ∼ 5 and 4 × 10 8 electrons emitted from the foil per pulse was studied. The monitor can also be used to measure the profiles of antiproton beams in the future facilities of Facility for Low-energy Antiproton Ion Research (FLAIR) or Extra Low Energy Antiproton Ring (ELENA).

Spatial and temporal beam profile monitor with nanosecond resolution for CERN's Linac4 and Superconducting Proton Linac

A 52 quadrupole-magnet FODO lattice has been assembled and operated at the Los Alamos National Laboratory. The purpose of this lattice is to provide a platform to measure the resulting beam halo as the first four magnets of the lattice produce various mismatch conditions. These data are then compared with particle simulations so that halo formation mechanisms may be better understood. The lattice is appended to the LEDA 6.7-MeV radiofrequency quadrupole (RFQ) and is followed by a short high-energy beam transport (HEBT) that safely dumps the beam into a 670-kW beam stop. Beam diagnostic instruments are interspersed within the lattice and HEBT. The primary instruments for measuring the beam halo are nine interceptive devices that acquire the beam's horizontal and vertical projected particle density distributions out to an approximate 10/sup 5/:1 dynamic range. These distributions are acquired using both traditional wire scanners and water-cooled graphite scraping devices. The lattice and HEBT instrumentation set also includes position, bunched-beam current, pulsed current, and beam loss measurements. This paper briefly describes and details the operation of each instrument compares measured data from the different types of instruments, and refers to other detailed papers.

/pdf/experience-with-the-low-energy-demonstration-accelerator-4cdfv40dwo.pdf

Experience with the low energy demonstration accelerator (LEDA) halo experiment beam instrumentation

The LEDA 75 keV injector and 6.7 MeV RFQ have been tested with pulsed and cw proton beam currents up to 100 mA. Several LINAC2000 papers give the results of those measurements. A follow-on experiment, to intentionally introduce and measure beam halo on the RFQ output beam, is reported in several papers at this conference (PAC2001). In this paper we summarize the LEDA RFQ commissioning results and the beam-halo measurements and we discuss future test plans for this high-current, high-average-power RF structures test bed.

/pdf/low-energy-demonstration-accelerator-leda-test-results-and-3fbtqj71zp.pdf

Low-Energy Demonstration Accelerator (LEDA) test results and plans

An experimental effort has been undertaken to investigate the production of halo particles in a proton beam having significant space charge forces. The LEDA RFQ was used to inject a pulsed 6.7 MeV 15-75 mA beam into a linear FODO channel. Four matching quads at the input of this 52-quadrupole transport line were used to generate specific mismatch oscillations, believed to be a key mechanism in the generation of beam halo. A suite of diagnostics that provide beam profile measurements over a wide dynamic range enabled a detailed comparison of measurements with theoretical models.

/pdf/measurements-of-halo-generation-for-a-proton-beam-in-a-fodo-18vosy198n.pdf

Measurements of halo generation for a proton beam in a FODO channel

The Low Energy Demonstration Accelerator (LEDA) facility has been used to characterize the pulsed- and cw-beam performance of a 6.7 MeV, 100 mA radio frequency quadrupole (RFQ). Diagnostic instrumentation, primarily located in a short beam transport downstream of the RFQ, allow facility commissioners and operators to measure and monitor the RFQ’s accelerated and total beam transmission, beam loss, bunched beam current, beam energy and output phase, and beam position. Transverse beam profile measurements are acquired under both low and high duty-factor pulsed beam conditions using a slow wire scanner and a camera that images beam-induced fluorescence. The wire scanner is also used to acquire transverse beam emittance information using a technique known as a “quad scan”. This paper reviews the measurement performance and discusses the resulting data.

/pdf/leda-beam-diagnostics-instrumentation-measurement-49kvflw6l6.pdf

LEDA beam diagnostics instrumentation: Measurement comparisons and operational experience

The halo experiment presently being conducted at the Low Energy Demonstration Accelerator (LEDA) at Los Alamos National Laboratory (LANL) has specific instruments that acquire horizontally and vertically projected particle-density beam distributions out to greater than 10{sup 5}:1 dynamic range. They measure the core of the distributions using traditional wire scanners, and the tails of the distribution using water-cooled graphite scraping devices. The wire scanner and halo scrapers are mounted on the same moving frame whose location is controlled with stepper motors. A sequence within the Experimental Physics and Industrial Control System (EPICS) software communicates with a National Instrument LabVIEW virtual instrument to control the motion and location of the scanner/scraper assembly. Secondary electrons from the wire scanner 0.03-mm carbon wire and protons impinging on the scraper are both detected with a lossy-integrator electronic circuit. Algorithms implemented within EPICS and in Research Systems Interactive Data Langugage (IDL) subroutines analyse and plot the acquired distributions. This paper describes this beam profile instrument, describes their experience with its operation, compares acquired profile data with simulations, and discusses various beam profile phenomena specific to the halo experiment.

https://cern.ch/AccelConf/d01/papers/CT05.pdf

Beam-Profile Instrumentation For Beam-Halo Measurement: Overall Description, Operation, And Beam Data

Within the halo experiment presently being conducted at the Low Energy Demonstration Accelerator (LEDA) at Los Alamos National Laboratory, specific beam instruments that acquire horizontally and vertically projected particle-density distributions out to approximately 10/sup 5/:1 dynamic range are located throughout the 52-magnet halo lattice. We measure the core of the distributions using traditional wire scanners, and the tails of the distribution using water-cooled graphite scraping devices. The wire scanner and halo scrapers are mounted on the same moving frame whose location is controlled with stepper motors. A sequence within the Experimental Physics and Industrial Control System (EPICS) software communicates with a National Instruments LabVIEW virtual instrument to control the motion and location of the scanner/scraper assembly. Secondary electrons from the wire scanner 0.033-mm carbon wire and protons impinging on the scraper are both detected with a lossy-integrator electronic circuit. Algorithms implemented within EPICS and in Research System's Interactive Data Language subroutines analyze and plot the acquired distributions. This paper describes this beam profile instrument, describes our experience with its operation, compares acquired profile data with simulation, and refers to other detailed papers.

/pdf/beam-profile-instrumentation-for-beam-halo-measurement-2huocdlghj.pdf

Beam-profile instrumentation for beam-halo measurement: overall description and operation

The Low-Energy Demonstration Accelerator (LEDA), designed and built at the Los Alamos National Laboratory, is part of the Accelerator Production of Tritium (APT) program and provides a platform for measuring high-power proton beam-halo formation. The technique used for measuring the beam halo employs nine combination Wire Scanner and Halo Scraper (WS/HS) devices. This paper focuses on the experience gained in the use of National Instrument (NI) LabVIEW VIs and motion controllers, and Compumotor electronic drive units and motors. The base configuration couples a Compumotor motor driven by a Parker-Hannifin Gemini GT Drive unit. The drive unit is controlled by a NI PXI-7344 controller card, which in turn is controlled by a PC running custom built NI LabVIEW VIs. The function of the control VI's is to interpret instructions from the main control system, the Experimental Physics and Industrial Control System (EPICS), and carry out the corresponding motion commands. The main control VI has to run all nineteen WS/HS motor axes used in the accelerator. A basic discussion of the main accelerator control system, EPICs which is hosted on a VXI platform, and its interface with the PC based LabVIEW motion control software is included.

/pdf/design-and-experience-with-the-ws-hs-assembly-movement-using-esqgez3jhb.pdf

Design and experience with the WS/HS assembly movement using LabVIEW VIs, National Instrument motion controllers, and compumotor electronic drive units and motors

M. W. Stettler

Papers

Experience with the low energy demonstration accelerator (LEDA) halo experiment beam instrumentation

LEDA beam diagnostics instrumentation: Measurement comparisons and operational experience

Beam-Profile Instrumentation For Beam-Halo Measurement: Overall Description, Operation, And Beam Data

Beam-profile instrumentation for beam-halo measurement: overall description and operation

Design and experience with the WS/HS assembly movement using LabVIEW VIs, National Instrument motion controllers, and compumotor electronic drive units and motors