Film cooling characteristics of a single round hole at various streamwise angles in a crossflow: Part I effectiveness

Adiabatic film cooling effectiveness on a flat plate surface downstream of a row of cylindrical holes is investigated. Highly resolved two dimensional surface data were measured by means of infrared thermography and carefully corrected for local conduction and radiation effects [1]. These locally acquired data are laterally averaged to give the streamwise distributions of the effectiveness. An independent variation of the flow parameters blowing rate, density ratio, and turbulence intensity as well as the geometrical parameters streamwise ejection angle and hole spacing is examined. The influences of these parameters on the laterally effectiveness is discussed and interpreted with the help of surface distributions of effectiveness and heat transfer coefficients presented in earlier publications [1, 2]. Besides the known jet in cross-flow behavior of coolant ejected from discrete holes, these data demonstrate the effect of adjacent jet interaction and its impact on jet lift-off and adiabatic effectiveness. In utilizing this large matrix of measurements the effect of single parameters and their interactions are correlated. The important scaling parameters of the effectiveness are shaped out during the correlation process and are discussed. The resulting new correlation is designed to yield the quantitatively correct effectiveness as a result of the interplay of the jet in crossflow behavior and the adjacent jet interaction. It is built modularly to allow for future inclusion of additional parameters. The new correlation is valid without any exception within the full region of interest, reaching from the point of the ejection to far downstream, for all combinations of flow and geometry parameters.Copyright © 2002 by ASME

Correlation of Film-Cooling Effectiveness From Thermographic Measurements at Enginelike Conditions

The demand of improved thermal efficiency and high power output of modern gas turbine engines leads to extremely high turbine inlet temperatures and pressure ratios. Sophisticated cooling schemes including film cooling are widely used to protect vanes and blades from failure and to achieve high component life-times. Besides standard cylindrical cooling hole geometry, shaped injection holes are used in modern film cooling applications in order to improve cooling performance and to reduce the necessary cooling air flow. However, complex hole shapes may lead to manufacturing constraints and high costs. This paper evaluates some film cooling injection geometry with different complexity. The comparison is based on measurements of the adiabatic film cooling effectiveness and the heat transfer coefficient downstream of the injection location. In total, 4 different film cooling hole configurations are investigated: A single row of fanshaped holes with and without a compound injection angle, a double row of cylindrical holes and a double row of discrete slots, both in staggered arrangement. All holes are inclined 45° with respect to the model’s surface. During the measurements, the influence of coolant blowing ratio is determined. Additionally, the influence of cooling air feeding direction into the fanshaped holes with the compound injection angle is investigated. An infrared thermography measurement system is used for highly resolved mappings of the model’s surface temperature. Accurate local temperature data is achieved by an In-Situ calibration procedure with the help of single thermocouples embedded in the test plate. A subsequent finite elements heat conduction analysis takes three-dimensional heat fluxes inside the test plate into account.© 2002 ASME

Assessment of Various Film Cooling Configurations Including Shaped and Compound Angle Holes Based on Large Scale Experiments

Detailed film cooling effectiveness distributions are obtained on a flat plate using the pressure sensitive paint (PSP) technique. The applicability of the PSP technique is expanded to include a coolant-to-mainstream density ratio of 1.4. The effect of density ratio on the film cooling effectiveness is coupled with varying blowing ratio (M = 0.25–2.0), freestream turbulence intensity (Tu = 1%–12.5%), and film hole geometry. The effectiveness distributions are obtained on three separate flat plates containing either simple angle, cylindrical holes, simple angle, fanshaped holes (α = 10°), or simple angle, laidback, fanshaped holes (α = 10°, γ = 10°). In all three cases, the film cooling holes are angled at θ = 35° from the mainstream flow. Using the PSP technique, the combined effects of blowing ratio, turbulence intensity, and density ratio are captured for each film cooling geometry. The detailed film cooling effectiveness distributions, for cylindrical holes, clearly show the effectiveness at the lowest blowing ratio is enhanced at the lower density ratio (DR = 1). However, as the blowing ratio increases, a transition occurs, leading to increased effectiveness with the elevated density ratio (DR = 1.4). In addition, the PSP technique captures an upstream shift of the coolant jet reattachment point as the density ratio increases or the turbulence intensity increases (at moderate blowing ratios for cylindrical holes). With the decreased momentum of the shaped film cooling holes, the greatest film cooling effectiveness is obtained at the lower density ratio (DR = 1.0) over the entire range of blowing ratios considered. In all cases, as the freestream turbulence intensity increases, the film effectiveness decreases; this effect is reduced as the blowing ratio increases for all three film hole configurations.Copyright © 2010 by ASME

Effect of Density Ratio on Flat Plate Film Cooling With Shaped Holes Using PSP

Local adiabatic film cooling effectiveness on a flat plate surface downstream a row of cylindrical holes was investigated. Geometrical parameters like blowing angle and hole pitch as well as the flow parameters blowing rate and density ratio were varied in a wide range emphasizing on engine relevant conditions. An IR-thermography technique was used to perform local measurements of the surface temperature field. A spatial resolution of up to 7 data points per hole diameter extending up to 80 hole diameters downstream of the ejection location was achieved. Since all technical surface materials have a finite thermoconductivity, no ideal adiabatic conditions could be established. Therefore, a procedure for correcting the measured surface temperature data based on a Finite Element analysis was developed. Heat loss over the backside of the testplate and remnant heat flux within the testplate in lateral and streamwise direction were taken into account. The local effectiveness patterns obtained are systematically analyzed to quantify the influence of the various parameters. As a result, a detailed description of the characteristics of local adiabatic film cooling effectiveness is given. Furthermore, the locally resolved experimental results can serve as a data base for the validation of CFD-codes predicting discrete hole film cooling.Copyright © 1999 by ASME

M. Y. Jabbari

Papers

Adiabatic wall temperature and heat transfer downstream of injection through two rows of holes

Adiabatic wall temperature and heat transfer downstream of injection through two rows of holes.

Adiabatic wall temperature and heat transfer downstream of injection through two rows of holes.