REVIEW: Ultrasound imaging

Ultrasonic Lamb modes typically propagate as a combination of multiple dispersive wave packets. Frequency components of each mode distribute widely in time domain due to dispersion and it is very challenging to separate individual modes by traditional signal processing methods. In the present study, a method of dispersion compensation is proposed for the purpose of mode separation. This numerical method compensates, i.e., compresses, the individual dispersive waveforms into temporal pulses, which thereby become nearly un-overlapped in time and frequency and can thus be extracted individually by rectangular time windows. It was further illustrated that the dispersion compensation also provided a method for predicting the plate thickness. Finally, based on reversibility of the numerical compensation method, an artificial dispersion technique was used to restore the original waveform of each mode from the separated compensated pulse. Performances of the compensation separation techniques were evaluated by processing synthetic and experimental signals which consisted of multiple Lamb modes with high dispersion. Individual modes were extracted with good accordance with the original waveforms and theoretical predictions.

Mode separation of Lamb waves based on dispersion compensation method.

This paper reports for the first time on inverse estimation of several bone properties from guided-wave measurements in human bone samples. Previously, related approaches have focused on ultrasonic estimation of a single bone property at a time. The method is based on two steps: the multi-Lamb mode response is analyzed using the singular value decomposition signal processing method recently introduced in the field, then an identification procedure is run to find thickness and anisotropic elastic properties of the considered specimen. Prior to the measurements on bone, the method is validated on cortical bone-mimicking phantoms. The repeatability and the trueness of the estimated parameters on bone-mimicking phantoms were found around a few percent. Estimation of cortical thickness on bone samples was in good agreement with cortical thickness derived from high-resolution peripheral quantitative computed tomography data analysis of the samples.

/pdf/combined-estimation-of-thickness-and-velocities-using-136z8i1t0s.pdf

Combined estimation of thickness and velocities using ultrasound guided waves: a pioneering study on in vitro cortical bone samples

We introduce an ultrasonic quantitative imaging method for long bones based on full-waveform inversion. The cost function is defined as the difference in the L 2-norm sense between observed data and synthetic results at a given iteration of the iterative inversion process. For simplicity, and in order to reduce the computational cost, we use a two-dimensional acoustic approximation. The inverse problem is solved iteratively based on a quasi-Newton technique called the Limited-memory Broyden-Fletcher-Goldfarb-Shanno method. We show how the technique can be made to work fine for benchmark models consisting of a single cylinder, and then five cylinders, the latter case including significant multiple diffraction effects. We then show pictures obtained for a tibia-fibula bone pair model. Convergence is fast, typically in 15 to 30 iterations in practice in each frequency band used. We discuss the so-called 'cycle skipping' effect that can occur in such full waveform inversion techniques and make them remain trapped in a local minimum of the cost function. We illustrate strategies that can be used in practice to avoid this. Future work should include viscoelastic materials rather than acoustic, and real data instead of synthetic data.

Ultrasonic computed tomography based on full-waveform inversion for bone quantitative imaging

Bone quality is determined by a variety of compositional, micro- and ultrastructural properties of the mineralized tissue matrix. In contrast to X-ray-based methods, the interaction of acoustic waves with bone tissue carries information about elastic and structural properties of the tissue. Quantitative ultrasound (QUS) methods represent powerful alternatives to ionizing x-ray based assessment of fracture risk. New in vivo applicable methods permit measurements of fracture-relevant properties, [eg, cortical thickness and stiffness at fragile anatomic regions (eg, the distal radius and the proximal femur)]. Experimentally, resonance ultrasound spectroscopy and acoustic microscopy can be used to assess the mesoscale stiffness tensor and elastic maps of the tissue matrix at microscale resolution, respectively. QUS methods, thus, currently represent the most promising approach for noninvasive assessment of components of fragility beyond bone mass and bone microstructure providing prospects for improved assessment of fracture risk.

Ultrasound to assess bone quality.

This paper is devoted to a method of extraction of guided waves phase velocities from experimental signals. Measurements are performed using an axial transmission device consisting of a linear arrangement of emitters and receivers placed on the surface of the inspected specimen. The technique takes benefit of using both multiple emitters and receivers and is validated on a reference wave guide. The guided mode phase velocities are obtained using a projection in the singular vectors basis. The singular vectors are determined by the singular values decomposition (SVD) of the response matrix between the two arrays in the frequency domain. This technique enables to recover accurately guided wave phase velocity dispersion curves. The SVD based approach was designed to overcome limitations of spatio-temporal Fourier transform for receiver array of limited spatial extent as in the case of clinical assessment of cortical bone in axial transmission.

/pdf/guided-wave-phase-velocity-measurement-using-multi-emitter-18xxeyfb9p.pdf

Guided wave phase velocity measurement using multi-emitter and multi-receiver arrays in the axial transmission configuration.

The objective of this study is to make cross-sectional ultrasonic quantitative tomography of the diaphysis of long bones. Ultrasonic propagation in bones is affected by the severe mismatch between the acoustic properties of this biological solid and those of the surrounding soft medium, namely, the soft tissues in vivo or water in vitro. Bone imaging is then a nonlinear inverse-scattering problem. In this paper, we showed that in vitro quantitative images of sound velocities in a human femur cross section could be reconstructed by combining ultrasonic reflection tomography (URT), which provides images of the macroscopic structure of the bone, and ultrasonic transmission tomography (UTT), which provides quantitative images of the sound velocity. For the shape, we developed an image-processing tool to extract the external and internal boundaries and cortical thickness measurements. For velocity mapping, we used a wavelet analysis tool adapted to ultrasound, which allowed us to detect precisely the time of flight from the transmitted signals. A brief review of the ultrasonic tomography that we developed using correction algorithms of the wavepaths and compensation procedures are presented. Also shown are the first results of our analyses on models and specimens of long bone using our new iterative quantitative protocol.

https://iopscience.iop.org/article/10.1088/0031-9155/50/11/013/pdf

Marilyne Talmant

Papers

Guided wave phase velocity measurement using multi-emitter and multi-receiver arrays in the axial transmission configuration.

Progress towards in vitro quantitative imaging of human femur using compound quantitative ultrasonic tomography.