The wind power generation is a rapidly growing grid integrated renewable energy (RE) technology with an installed capacity of 539.291 GW. The capability of the wind energy conversion system (WECS) to remain integrated into the utility network in the case of low voltage events is called low-voltage ride-through (LVRT) capability. This paper offers a comprehensive overview of improvement techniques of the LVRT capability in WECS to increase the wind energy penetration level in the utility grid. Exhibited portrait manifests a broad spectrum of 1) wind turbines, 2) electrical generators used for wind power applications, 3) international grid codes applicable for grid integration of WECS, 4) LVRT fundamentals in WECS, 5) wind turbines LVRT methods by doubly fed induction generator (DFIG), 6) wind turbines LVRT methods by permanent magnet synchronous generators (PMSG), and 7) LVRT methods of wind turbines using squirrel cage induction generator (SCIG). This ready-reckoner paper critically reviews and classifies more than 190 research papers on LVRT issues, practices, and available technologies for grid integration in wind energy systems, and it aims to be a quick reference for the researchers, designers, manufacturers, and engineers working in the same field.

/pdf/comprehensive-overview-of-low-voltage-ride-through-methods-4w0m6fnpvx.pdf

Comprehensive Overview of Low Voltage Ride Through Methods of Grid Integrated Wind Generator

The utilization of renewable energy sources (RESs) has become significant throughout the world, especially over the last two decades. Although high-level RESs penetration reduces negative environmental impact compared to conventional fossil fuel-based energy generation, control issues become more complex as the system inertia is significantly decreased due to the absence of conventional synchronous generators. Some other technical issues, high uncertainties, low fault ride through capability, high fault current, low generation reserve, and low power quality, arise due to RESs integration. Renewable energy like solar and wind are highly uncertain due to the intermittent nature of wind and sunlight. Cutting edge technologies including different control strategies, optimization techniques, energy storage devices, and fault current limiters are employed to handle those issues. This paper summarizes several challenges in the integration process of high-level RESs to the existing grid. The respective solutions to each challenge are presented and discussed. A comprehensive list of challenges and solutions, for both wind and solar energy integration cases, are well documented. Finally, the future recommendations are provided to solve the several problems of renewable energy integration which could be key research areas for the industry personnel and researchers.

High-Level Penetration of Renewable Energy Sources Into Grid Utility: Challenges and Solutions

Fault ride-through control of grid-connected photovoltaic power plants: A review

This paper deals with the control of a variable-speed wind energy conversion (WEC) system using a squirrel cage induction generator (SCIG) connected to the grid through a back-to-back three phase (AC-DC-AC) power converter. The sliding mode control technique is used to control the WEC system. The objective of the controllers is to force the states of the system to track their desired states. One controller is used to regulate the generator speed and the flux so that maximum power is extracted from the wind. Another controller is used to control the grid side converter, which controls the DC bus voltage and the active and reactive powers injected into the grid. The performance of the controlled wind energy conversion system is verified through MATLAB simulations, which show that the controlled system performs well.

Sliding Mode Control of a Variable- Speed Wind Energy Conversion System Using a Squirrel Cage Induction Generator

One of the major challenges with electric shipboard power systems (SPS) is preserving the survivability of the system under fault situations. Some minor faults in SPS can result in catastrophic consequences. Therefore, it is essential to investigate available fault management techniques for SPS applications that can enhance SPS robustness and reliability. Many recent studies in this area take different approaches to address fault tolerance in SPSs. This paper provides an overview of the concepts and methodologies that are utilized to deal with faults in the electric SPS. First, a taxonomy of the types of faults and their sources in SPS is presented; then, the methods that are used to detect, identify, isolate, and manage faults are reviewed. Furthermore, common techniques for designing a fault management system in SPS are analyzed and compared. This paper also highlights several possible future research directions.

Mohammad Hassan Khooban

Papers

A novel control system design to improve LVRT capability of fixed speed wind turbines using STATCOM in presence of voltage fault