In the previous paper Ralph Brodd and Martin Winter described the different kinds of batteries and fuel cells. In this paper I will describe lithium batteries in more detail, building an overall foundation for the papers that follow which describe specific components in some depth and usually with an emphasis on the materials behavior. The lithium battery industry is undergoing rapid expansion, now representing the largest segment of the portable battery industry and dominating the computer, cell phone, and camera power source industry. However, the present secondary batteries use expensive components, which are not in sufficient supply to allow the industry to grow at the same rate in the next decade. Moreover, the safety of the system is questionable for the large-scale batteries needed for hybrid electric vehicles (HEV). Another battery need is for a high-power system that can be used for power tools, where only the environmentally hazardous Ni/ Cd battery presently meets the requirements. A battery is a transducer that converts chemical energy into electrical energy and vice versa. It contains an anode, a cathode, and an electrolyte. The anode, in the case of a lithium battery, is the source of lithium ions. The cathode is the sink for the lithium ions and is chosen to optimize a number of parameters, discussed below. The electrolyte provides for the separation of ionic transport and electronic transport, and in a perfect battery the lithium ion transport number will be unity in the electrolyte. The cell potential is determined by the difference between the chemical potential of the lithium in the anode and cathode, ∆G ) -EF. As noted above, the lithium ions flow through the electrolyte whereas the electrons generated from the reaction, Li ) Li+ + e-, go through the external circuit to do work. Thus, the electrode system must allow for the flow of both lithium ions and electrons. That is, it must be both a good ionic conductor and an electronic conductor. As discussed below, many electrochemically active materials are not good electronic conductors, so it is necessary to add an electronically conductive material such as carbon * To whom correspondence should be addressed. Phone and fax: (607) 777-4623. E-mail: stanwhit@binghamton.edu. 4271 Chem. Rev. 2004, 104, 4271−4301

http://www.chemie.uni-regensburg.de/Anorganische_Chemie/Vortrag/StudentenWS06-07/Vortrag_Amereller.pdf

Lithium Batteries and Cathode Materials

Although non-aqueous Li-ion batteries possess significantly higher energy density than their aqueous counterparts, the latter can be more feasible for grid-scale applications when cost, safety and cycle life are taken into consideration. Moreover, aqueous Zn-ion batteries have an energy storage advantage over alkali-based batteries as they can employ Zn metal as the negative electrode, dramatically increasing energy density. However, their development is plagued by a limited choice of positive electrodes, which often show poor rate capability and inadequate cycle life. Here we report a vanadium oxide bronze pillared by interlayer Zn2+ ions and water (Zn0.25V2O5⋅nH2O), as the positive electrode for a Zn cell. A reversible Zn2+ ion (de)intercalation storage process at fast rates, with more than one Zn2+ per formula unit (a capacity up to 300 mAh g−1), is characterized. The Zn cell offers an energy density of ∼450 Wh l−1 and exhibits a capacity retention of more than 80% over 1,000 cycles, with no dendrite formation at the Zn electrode. High-performing positive electrode materials are crucial for the development of aqueous Zn-ion batteries. Here the authors report a battery based on reversible intercalation of Zn ions in a layered Zn0.25V2O5⋅nH2O-based positive electrode, which exhibits high-capacity and long-term cycling stability.

A high-capacity and long-life aqueous rechargeable zinc battery using a metal oxide intercalation cathode

In order to address power and energy demands of mobile electronics and electric cars, Li-ion technology is urgently being optimized by using alternative materials. This article presents a review of our recent progress dedicated to the anode and cathode materials that have the potential to fulfil the crucial factors of cost, safety, lifetime, durability, power density, and energy density. Nanostructured inorganic compounds have been extensively investigated. Size effects revealed in the storage of lithium through micropores (hard carbon spheres), alloys (Si, SnSb), and conversion reactions (Cr(2)O(3), MnO) are studied. The formation of nano/micro core-shell, dispersed composite, and surface pinning structures can improve their cycling performance. Surface coating on LiCoO(2) and LiMn(2)O(4) was found to be an effective way to enhance their thermal and chemical stability and the mechanisms are discussed. Theoretical simulations and experiments on LiFePO(4) reveal that alkali metal ions and nitrogen doping into the LiFePO(4) lattice are possible approaches to increase its electronic conductivity and does not block transport of lithium ion along the 1D channel.

Research on Advanced Materials for Li‐ion Batteries

/pdf/recent-advances-in-zn-ion-batteries-utvauxy3ub.pdf

Recent Advances in Zn-Ion Batteries

Recent studies have revealed that single-layer transition-metal oxides and dichalcogenides (MX2) might offer properties superior to those of graphene. So far, only very few MX2 compounds have been synthesized as suspended single layers, and some of them have been exfoliated as thin sheets. Using first-principles structure optimization and phonon calculations based on density functional theory, we predict that, out of 88 different combinations of MX2 compounds, several of them can be stable in free-standing, single-layer honeycomb-like structures. These materials have two-dimensional hexagonal lattices and have top-view appearances as if they consisted of either honeycombs or centered honeycombs. However, their bonding is different from that of graphene; they can be viewed as a positively charged plane of transition-metal atoms sandwiched between two planes of negatively charged oxygen or chalcogen atoms. Electron correlation in transition-metal oxides was treated by including Coulomb repulsion through LDA...

/pdf/stable-single-layer-mx2-transition-metal-oxides-and-5cihdvwat4.pdf

Naoichi Yamamoto

Papers

Layered structures of vanadium pentoxide gels

Protonic conduction and defect structures in Sr-doped LaPO4

Hydrothermal Synthesis of Lanthanum Vanadates: Synthesis and Crystal Structures of Zircon-Type LaVO4 and a New Compound LaV3O9

Crystal Structures and Transition Mechanism of VO2(A)

Powder X-ray crystal structure of VO2(A)