Methods and apparatus to perform measurements are disclosed. An example method disclosed herein for a user equipment (UE) to perform measurements comprises receiving configuration information from a network, the configuration information to configure the UE to perform logging of measurements in an idle mode, logging measurements in the idle mode, and sending an indication that logged measurements are available.

Methods and apparatus to perform measurements

Techniques for mitigating interference on control channels in a wireless communication network are described. In an aspect, high interference on radio resources used for a control channel may be mitigated by sending a request to reduce interference to one or more interfering stations. Each interfering station may reduce its transmit power on the radio resources, which may then allow the control channel to observe less interference. In one design, a user equipment (UE) may detect high interference on radio resources used for a control channel by a desired base station. The UE may send a request to reduce interference on the radio resources to an interfering base station, which may reduce its transmit power on the radio resources. The UE may receive the control channel on the radio resources from the desired base station and may observe less interference from the interfering base station.

Interference mitigation for control channels in a wireless communication network

Neighbor relation information management involves, for example: acquiring, reporting, and exchanging neighbor relation information. In some cases, neighbor relation information is acquired and/or reported in a manner that does not significantly impact other functionality of the access terminal. For example, an access terminal may be configured to acquire and/or report neighbor relation information only during one or more defined radio states. In some cases, the acquisition of neighbor relation information is based on a neighbor relation threshold. In some cases, an access terminal does not immediately report measured neighbor relation information and instead stores the information for reporting at a later time. In some cases, a transmitted indication is used to facilitate retrieval of neighbor relation information from an access terminal. In some cases, neighbor relation information acquired from an access terminal is exchanged over a direct interface between access points.

Neighbor relation information management

Techniques for managing interference in a wireless network are described. A base station may receive enhanced pilot measurement reports from user equipments (UEs) and may make an interference management decision based on the received reports. The base station may select a serving base station for a UE based on an enhanced pilot measurement report received from the UE. The base station may determine resources with a low target interference level at a neighbor base station and may avoid scheduling a UE for uplink transmission on the resources. The base station may also determine whether to reserve resources for a neighbor base station based on data performance of the neighbor base station, whether the neighbor base station observes high interference from UEs served by the base station, or whether UEs served by the neighbor base station observe high interference from the base station, which may be determined based on the enhanced pilot measurement reports.

Interference management based on enhanced pilot measurement reports

An inter-system handover system for a wireless communication system supports hand-down and hand-up of user equipment (UE) to different radio access technologies, including synchronous and asynchronous systems. Latency and handover connection failures are reduced by an access node (nodeB) broadcasting information about neighboring systems (targets) when the UE reception (RX) capability is both inside or outside the reception range of the target. A single RX chain is sufficient, although transitioning between a wireless wide area network (WWAN) to a wireless local area network may (WLAN) may advantageously benefit from simultaneous operation on two Rx chains. Optimized list of neighboring RAT systems (targets) are broadcast from the network, including measurement parameters and reporting instructions. Thereby, UE-driven reporting minimizes latencies. UE reports other-system searches to network only if needed for a handover. In addition, handover requests can be bundled with other-system measurement information, if necessary, for additional efficiencies.

Method and apparatus for inter-system handover

A method includes establishing a first radio link with a serving network entity and a second radio link with a target network entity, commencing a soft handover from the serving network entity to the target network entity, receiving a quality target from a network comprising the serving and target network entities, and applying the quality target only to the first radio link to generate a power control command.

Apparatus, method and computer program providing enhanced fractional dedicated physical channel downlink power control during soft handover

The negative impacts on a user equipment (UE) caused by the UE' s support in network self-configuration and optimization is limited to an acceptable level by controlling user equipment measurements in a network to configure neighbor lists; requesting one or more measurements; the user equipment performing measurements in one or more adjacent cells in response to one or more measurement requests; reporting the measurements; and identifying cells in the network to be included in the neighbor list such that the user equipment measurements support network self- configuration and optimization

Control method for network configuration measurements

Various methods for selecting a network access subscription are provided. One example method includes receiving a request to participate in a communications session, determining that at least two subscriptions for network access are available, determining tariffs for one or more connection types that are available through each subscription, 5 determining cost factors for each connection type of the at least two subscriptions based on the tariffs, and selecting a target subscription and a target connection type for use in satisfying the request based on the cost factors. Similar and related example methods and example apparatuses are also provided.

Method and apparatus for selecting a network access subscription

The negative impacts on a user equipment (UE) caused by the UE's support in network self-configuration and optimization is limited to an acceptable level by controlling user equipment measurements in a network to configure neighbor lists; requesting one or more measurements; the user equipment performing measurements in one or more adjacent cells in response to one or more measurement requests; reporting the measurements; and identifying cells in the network to be included in the neighbor list such that the user equipment measurements support network self-configuration and optimization.

Nielsen Sari

Papers

Apparatus, method and computer program providing enhanced fractional dedicated physical channel downlink power control during soft handover

Control method for network configuration measurements

Method and apparatus for selecting a network access subscription

Method for controlling user equipment measurements in a network to configure neighbor lists

Method, computer program and apparatus for selecting a network access subscription