Advances in the development of novel cobalt Fischer-Tropsch catalysts for synthesis of long-chain hydrocarbons and clean fuels.

Catalyst productivity and selectivity to C5+ hydrocarbons are critical design criteria in the choice of Fischer-Tropsch synthesis (FTS) catalysts and reactors. Cobalt-based catalysts appear to provide the best compromise between performance and cost for the synthesis of hydrocarbons from CO/H2 mixtures. Optimum catalysts with high cobalt concentration and site density can be prepared by controlled reduction of nitrate precursors introduced via melt or aqueous impregnation methods. FTS turnover rates are independent of Co dispersion and support identity over the accessible dispersion range (0.01–0.12) at typical FTS conditions. At low reactant pressures or conversions, water increases FTS reaction rates and the selectivity to olefins and to C5+ hydrocarbons. These water effects depend on the identity of the support and lead to support effects on turnover rates at low CO conversions. Turnover rates increase when small amounts of Ru (Ru/Co<0.008 at.) are added to Co catalysts. C5+ selectivity increases with increasing Co site density because diffusion-enhanced readsorption of α-olefins reverses, β-hydrogen abstraction steps and inhibits chain termination. Severe diffusional restrictions, however, can also deplete CO within catalyst pellets and decrease chain growth probabilities. Therefore, optimum C5+ selectivities are obtained on catalysts with moderate diffusional restrictions. Diffusional constraints depend on pellet size and porosity and on the density and radial location of Co sites within catalyst pellets. Slurry bubble column reactors and the use of eggshell catalyst pellets in packed-bed reactors introduce design flexibility by decoupling the characteristic diffusion distance in catalyst pellets from pressure drop and other reactor constraints.

Design, synthesis, and use of cobalt-based Fischer-Tropsch synthesis catalysts

Temperature programmed reduction (TPR) and hydrogen chemisorption combined with reoxidation measurements were used to define the reducibility of supported cobalt catalysts. Different supports (e.g. Al2O3, TiO2, SiO2, and ZrO2 modified SiO2 or Al2O3) and a variety of promoters, including noble metals and metal cations, were examined. Significant support interactions on the reduction of cobalt oxide species were observed in the order Al2O3>TiO2>SiO2. Addition of Ru and Pt exhibited a similar catalytic effect by decreasing the reduction temperature of cobalt oxide species, and for Co species where a significant surface interaction with the support was present, while Re impacted mainly the reduction of Co species interacting with the support. For catalysts reduced at the same temperature, a slight decrease in cluster size was observed in H2 chemisorption/pulse reoxidation with noble metal promotion, indicating that the promoter aided in reducing smaller Co species that interacted with the support. On the other hand, addition of non-reducible metal oxides such as B, La, Zr, and K was found to cause the reduction temperature of Co species to shift to higher temperatures, resulting in a decrease in the percentage reduction. For both Al2O3 and SiO2, modifying the support with Zr was found to enhance the dispersion. Increasing the cobalt loading, and therefore the average Co cluster size, resulted in improvements to the percentage reduction. Finally, a slurry phase impregnation method led to improvements in the reduction profile of Co/Al2O3.

Fischer–Tropsch synthesis: support, loading, and promoter effects on the reducibility of cobalt catalysts

The effects of metal particle size in catalysis are of prime scientific and industrial importance and call for a better understanding. In this paper the origin of the cobalt particle size effects in Fischer−Tropsch (FT) catalysis was studied. Steady-State Isotopic Transient Kinetic Analysis (SSITKA) was applied to provide surface residence times and coverages of reaction intermediates as a function of Co particle size (2.6−16 nm). For carbon nanofiber supported cobalt catalysts at 210 °C and H2/CO = 10 v/v, it appeared that the surface residence times of reversibly bonded CHx and OHx intermediates increased, whereas that of CO decreased for small (<6 nm) Co particles. A higher coverage of irreversibly bonded CO was found for small Co particles that was ascribed to a larger fraction of low-coordinated surface sites. The coverages and residence times obtained from SSITKA were used to describe the surface-specific activity (TOF) quantitatively and the CH4 selectivity qualitatively as a function of Co particl...

On the origin of the cobalt particle size effects in Fischer-Tropsch catalysis.

National Natural Science Foundation of China [20625310, 20923004]; National Basic Research Program of China [2005CB221408, 2010CB732303]; Research Fund for the Doctoral Program of Higher Education [20090121110007]; Key Scientific Project of Fujian Province [2009HZ0002-1]

Robert C. Reuel

Papers

The stoichiometries of H2 and CO adsorptions on cobalt: Effects of support and preparation

Effects of support and dispersion on the CO hydrogenation activity/selectivity properties of cobalt

Cobalt-support interactions: their effects on adsorption and carbon monoxide hydrogenation activity and selectivity properties