Particle reinforced metal matrix composites are now being produced commerically, and in this paper the current status of these materials is reviewed. The different types of reinforcement being used, together with the alternative processing methods, are discussed. Depending on the initial processing method, different factors have to be taken into consideration to produce a high quality billet. With powder metallurgy processing, the composition of the matrix and the type of reinforcement are independent of one another. However, in molten metal processing they are intimately linked in terms of the different reactivities which occur between reinforcement and matrix in the molten state. The factors controlling the distribution of reinforcement are also dependent on the initial processing method. Secondary fabrication methods, such as extrusion and rolling, are essential in processing composites produced by powder metallurgy, since they are required to consolidate the composite fully. Other methods, suc...

Particle reinforced aluminium and magnesium matrix composites

The current understanding of the fundamentals of recrystallization is summarized. This includes understanding the as-deformed state. Several aspects of recrystallization are described: nucleation and growth, the development of misorientation during deformation, continuous, dynamic, and geometric dynamic recrystallization, particle effects, and texture. This article is authored by the leading experts in these areas. The subjects are discussed individually and recommendations for further study are listed in the final section.

/pdf/current-issues-in-recrystallization-a-review-12181rj4pn.pdf

Current issues in recrystallization: a review

Dynamic Recrystallization of Minerals

Discontinuous dynamic recrystallization (involving nucleation and grain growth) is rarely observed in metals with high stacking fault energies, such as aluminium. In this metal, two other types of recrystallization have been observed: continuous dynamic recrystallization (CDRX, i.e. the transformation of subgrains into grains); and geometric dynamic recrystallization (due to the evolution of the initial grains). The main purpose of this work was to bring clearly into evidence and to better characterize CDRX. Uniaxial compression tests were carried out at 0.7 T m and 10 −2 s −1 on three types of polycrystalline aluminium: a pure aluminium (1199), a commercial purity aluminium (1200) and an Al-2.5wt.%Mg alloy (5052), and also on single crystals of pure aluminium. In addition, 1200 aluminium specimens were strained in torsion. The deformed microstructures were investigated at various strains using X-ray diffraction, optical microscopy, scanning electron microscopy and electron back-scattered diffraction. Observations of the single crystalline samples confirm that subgrain boundaries can effectively transform into grain boundaries, especially when the initial orientation is unstable. In the case of polycrystalline specimens, after separating the effects of the initial and new grain boundaries, it turns out that CDRX operates faster in the 1200 aluminium compared to the two other grades. Moreover, it appears that the strain path does not alter noticeably the CDRX kinetics.

An experimental study of the recrystallization mechanism during hot deformation of aluminium

This graduate textbook presents a comprehensive, unified treatment of the materials science of deformation as applied to solid Earth geophysics and geology. The deformation of Earth materials is presented in a systematic way covering elastic, anelastic and viscous deformation. Advanced discussions on relevant debates are also included to bring readers a full picture of science in this interdisciplinary area. This textbook is ideal for graduate courses on the rheology and dynamics of solid Earth, and includes review questions with solutions so readers can monitor their understanding of the material presented. It is also a much-needed reference for geoscientists in many fields including geology, geophysics, geochemistry, materials science, mineralogy and ceramics.

Deformation of Earth Materials: An Introduction to the Rheology of Solid Earth

Well defined subgrain boundaries dominate the microstructural changes occurring during plastic flow of polycrystalline metals at elevated temperature. The quantitative influence of subgrain size on elevated-temperature plastic flow is considered. Based on the results of tests under constant-stress and constant-structure conditions, an equation is developed which predicts the creep rate as a function of subgrain size, stress, diffusion coefficient, and elastic modulus. In general, the subgrain size is a unique function of the current modulus-compensated flow stress, but if fine subgrains can be introduced and stabilized, large increases in creep strength may result. The applicability of the phenomenological relation developed to the behavior of dispersion-strengthened materials (where the second-phase particles may predetermine the effective subgrain size) is discussed. When subgrain effects are included, it is shown that the creep rate is less dependent on stacking fault energy than has been previously thought.

Flow Stress, Subgrain Size, and Subgrain Stability at Elevated Temperature

The high temperature flow stress behavior of an electron beam melted 26 Cr-1 Mo ferritic stainless steel was determined for large torsion strains (e ~ 15) over a temperature range from 400 °C (750 °F) to 1000 °C (1830 °F) and a strain rate range from 6 × 10-3 to 6.3 s-1. The room temperature compressive yield strength measured after torsional warm working was also investigated. It was found that the high temperature flow strength and the room temperature compressive yield strength were strong functions of the subgrain size. Strain softening was observed during warm working while the room temperature compressive yield strength was found to increase with prior torsional strain. The increase in the subgrain misorientation angle and, to a lesser extent, the subgrain shape change that occurs with increased warm working strain appear to be responsible for the strain dependence of the flow stress at both elevated and low temperatures.

Rodney H. Klundt

Papers

Flow Stress, Subgrain Size, and Subgrain Stability at Elevated Temperature

The influence of substructure on the elevated and room temperature strength of a 26 Cr-1 Mo ferritic stainless steel