FPGA-based cards for data concentration and readout are often used in data acquisition (DAQ) systems for high-energy physics experiments. The DMA engines implemented in FPGA enable efficient data transfer to the processing system’s memory. This paper presents a versatile DMA engine. It may be used in systems with FPGA-equipped PCIe boards hosted in a server and MPSoC-based systems with programmable logic connected directly to the AXI system bus. The core part of the engine is implemented in HLS to simplify further development and modifications. The design is modular and may be easily integrated with the user’s DAQ logic, assuming it delivers the data via a standard AXI-Stream interface. The engine and accompanying software are designed with flexibility in mind. They offer a simple single-packet mode for debugging and a high-performance multi-packet mode fully utilizing the computational power of the processing system. The number of used DAQ cards and the amount of memory used for the DMA buffer may be modified in the runtime without rebooting the system. That is particularly useful in the development and test setups. This paper also presents the development and testing methodology. The whole design is open-source and available in public repositories.

/pdf/versatile-dma-engine-for-high-energy-physics-data-17um7wfc.pdf

Versatile DMA Engine for High-Energy Physics Data Acquisition Implemented with High-Level Synthesis

Abstract Silicon Tracker for RAdioactive nuclei Studies at SAMURAI Experiments is a new detection system under construction for quasi-free scattering (QFS) measurements at 200–250 MeV/nucleon at the RIBF facility of the RIKEN Nishina Center. It consists of a charged-particle silicon tracker coupled with a dedicated thick liquid hydrogen target (up to 150-mm long) in a compact geometry to fit inside large scintillator or germanium arrays. Its design was optimized for two types of studies using QFS: missing-mass measurements and in-flight prompt $$\gamma $$ <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML"> <mml:mi>γ</mml:mi> </mml:math> -ray spectroscopy. This article describes (i) the resolution requirements needed to go beyond the sensitivity of existing systems for these two types of measurements, (ii) the conceptual design of the system using detailed simulations of the setup and (iii) its complete technical implementation and challenges. The final tracker aims at a sub-mm reaction vertex resolution and is expected to reach a missing-mass resolution below 2 MeV in $$\sigma $$ <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML"> <mml:mi>σ</mml:mi> </mml:math> for ( p , 2 p ) reactions when combined with the CsI(Na) CATANA array. 

/pdf/strasse-a-silicon-tracker-for-quasi-free-scattering-1eobip68.pdf

STRASSE: a silicon tracker for quasi-free scattering measurements at the RIBF

The GBTX ASIC is a standard solution for providing fast control and data readout for radiation detectors used in HEP experiments. However, it is subject to export control restrictions due to the usage of radiation-hard technology. An FPGA-based GBTX emulator (GBTxEMU) has been developed to enable the development of GBT-based readout chains in countries where the original GBTX cannot be imported. Thanks to utilizing a slightly modified GBT-FGPA core, it maintains basic compatibility with standard GBT-based systems. The GBTxEMU also may be an interesting solution for developing GBT-based readout chains for less demanding experiments.

GBTX emulator for development and special versions of GBT-based readout chains

The SMX chip is a front-end ASIC dedicated to the readout of STS and MUCH detectors in the CBM experiment. The production of the ASIC and the front-end boards based on it is just being started and requires thorough testing to assure quality. The paper describes the SMX tester based on a standard commercial Artix-7 FPGA module with an additional simple baseboard. In the standalone configuration, the tester is controlled via IPbus and enables full functional testing of connected SMX, FEB, or a full detector module. The software written in Python may easily be integrated with higher-level testing software.

Ryszard Romaniuk

Papers

GBTX emulator for development and special versions of GBT-based readout chains

SMX and front-end board tester for CBM readout chain.