Much has been written about theory and practice in the law, and the tension between practitioners and theorists. Judges do not cite theoretical articles often; they rarely "apply" theories to particular cases. These arguments are not revisited. Instead the Essay explores the working and interaction of theory and practice, practitioners and theorists. The Essay starts with a story about solving a legal issue using our intellectual tools - theory, practice, and their progenies: experience and "gut." Next the Essay elaborates on the nature of theory, practice, experience and "gut." The third part of the Essay discusses theories that are helpful to practitioners and those that are less helpful. The Essay concludes that practitioners theorize, and theorists practice. They use these intellectual tools differently because the goals and orientations of theorists and practitioners, and the constraints under which they act, differ. Theory, practice, experience and "gut" help us think, remember, decide and create. They complement each other like the two sides of the same coin: distinct but inseparable.

Of Theory and Practice

House of Quality

https://escholarship.org/content/qt4h56k1ch/qt4h56k1ch.pdf

Advanced monitoring of machining operations

The extensive development of electronic systems and telecommunications has lead to major concerns regarding electromagnetic pollution. Motivated by environmental questions and by a wide variety of applications, the quest for materials with high efficiency to mitigate electromagnetic interferences (EMI) pollution has become a mainstream field of research. This paper reviews the state-of-the-art research in the design and characterization of polymer/carbon based composites as EMI shielding materials. After a brief introduction, in Section 1, the electromagnetic theory will be briefly discussed in Section 2 setting the foundations of the strategies to be employed to design efficient EMI shielding materials. These materials will be classified in the next section by the type of carbon fillers, involving carbon black, carbon fiber, carbon nanotubes and graphene. The importance of the dispersion method into the polymer matrix (melt-blending, solution processing, etc.) on the final material properties will be discussed. The combination of carbon fillers with other constituents such as metallic nanoparticles or conductive polymers will be the topic of Section 4. The final section will address advanced complex architectures that are currently studied to improve the performances of EMI materials and, in some cases, to impart additional properties such as thermal management and mechanical resistance. In all these studies, we will discuss the efficiency of the composites/devices to absorb and/or reflect the EMI radiation.

Polymer/carbon based composites as electromagnetic interference (EMI) shielding materials

Light-weight nanocomposites filled with carbon nanotubes (CNTs) are developed for their significant potentials in electromagnetic shielding and attenuation for wide applications in electronics, communication devices, and specific parts in aircrafts and vehicles. Specifically, the introduction of a second phase into/onto CNTs for achieving CNT-based heterostructures has been widely pursued due to the enhancement in either dielectric loss or magnetic loss. In this work, ferroferric oxide (Fe(3)O(4)) was selected as the phase in multiwalled carbon nanotube (MWCNT)-based composites for enhancing magnetic properties to obtain improved electromagnetic attenuation. A direct comparison between the two-phase heterostructures (Fe(3)O(4)/MWCNTs) and polyaniline (PANI) coated Fe(3)O(4)/MWCNTs, namely, three-phase heterostructures (PANI/Fe(3)O(4)/MWCNTs), was made to investigate the interface influences of Fe(3)O(4) and PANI on the complex permittivity and permeability separately. Compared to PANI/Fe(3)O(4)/MWCNTs, Fe(3)O(4)/MWCNTs exhibited enhanced magnetic properties coupled with increased dielectric properties. Interfaces between MWCNTs and heterostructures were found to play a role in the corresponding properties. The evaluation of microwave absorption of their wax composites was carried out, and the comparison between Fe(3)O(4)/MWCNTs and PANI/Fe(3)O(4)/MWCNTs with respect to highly efficient microwave absorption and effective absorption bandwidth was discussed.

Ferroferric Oxide/Multiwalled Carbon Nanotube vs Polyaniline/Ferroferric Oxide/Multiwalled Carbon Nanotube Multiheterostructures for Highly Effective Microwave Absorption

The miniaturization of machine components is perceived by many as a requirement for the future technological development of a broad spectrum of products. Miniature components can provide smaller footprints, lower power consumption and higher heat transfer, since their surface-to-volume ratio is very high. To create these components, micro-meso-scale fabrication using miniaturized mechanical material removal processes has a unique advantage in creating 3D components using a variety of engineering materials. The motivation for micro-mechanical cutting stems from the translation of the knowledge obtained from the macro-machining domain to the micro-domain. However, there are challenges and limitations to micro-machining, and simple scaling cannot be used to model the phenomena of micro-machining operations. This paper surveys the current efforts in mechanical micro-machining research and applications, especially for micro-milling operations, and suggests areas from macro-machining that should be examined and researched for application to the improvement of micro-machining processes.

Investigation of micro-cutting operations

http://www.ppsconferences.org/public/abs_2011/56.pdf

Electrical and electromagnetic interference shielding properties of flow-induced oriented carbon nanotubes in polycarbonate

The electrical conductivity and electromagnetic interference shielding of injection molded multi-walled carbon nanotube/polystyrene composites

This paper investigates the mechanistic modeling of micro-milling forces, with consideration of the effects of ploughing, elastic recovery, run-out, and dynamics. A ploughing force model that takes the effect of elastic recovery into account is developed based on the interference volume between the tool and the workpiece. The elastic recovery is identified with experimental scratch tests using a conical indenter. The dynamics at the tool tip is indirectly identified by performing receptance coupling analysis through the mathematical coupling of the experimental dynamics with the analytical dynamics. The model is validated through micro end milling experiments for a wide range of cutting conditions.

Simon S. Park

Papers

Investigation of micro-cutting operations

Electrical and electromagnetic interference shielding properties of flow-induced oriented carbon nanotubes in polycarbonate

The electrical conductivity and electromagnetic interference shielding of injection molded multi-walled carbon nanotube/polystyrene composites

Modeling of dynamic micro-milling cutting forces

Modeling of minimum uncut chip thickness in micro machining of aluminum