Osteoblast adhesion on biomaterials.

In tissue engineering, a highly porous artificial extracellular matrix or scaffold is required to accommodate mammalian cells and guide their growth and tissue regeneration in three dimensions. However, existing three-dimensional scaffolds for tissue engineering proved less than ideal for actual applications, not only because they lack mechanical strength, but they also do not guarantee interconnected channels. In this paper, the authors analyze the factors necessary to enhance the design and manufacture of scaffolds for use in tissue engineering in terms of materials, structure, and mechanical properties and review the traditional scaffold fabrication methods. Advantages and limitations of these traditional methods are also discussed.

/pdf/the-design-of-scaffolds-for-use-in-tissue-engineering-part-i-2btlkct7hc.pdf

The Design of Scaffolds for Use in Tissue Engineering. Part I. Traditional Factors

A biodegradable nanofiber scaffold by electrospinning and its potential for bone tissue engineering.

Biomaterial developments for bone tissue engineering

Recent Developments in Ring Opening Polymerization of Lactones for Biomedical Applications

Bone formation was investigated in vitro by culturing stromal osteoblasts in three-dimensional (3-D), biodegradable poly(DL-lactic-co-glycolic acid) foams. Three polymer foam pore sizes, ranging from 150-300, 300-500, and 500-710 microns, and two different cell seeding densities, 6.83 x 10(5) cells/cm2 and 22.1 x 10(5) cells/cm2, were examined over a 56-day culture period. The polymer foams supported the proliferation of seeded osteoblasts as well as their differentiated function, as demonstrated by high alkaline phosphatase activity and deposition of a mineralized matrix by the cells. Cell number, alkaline phosphatase activity, and mineral deposition increased significantly over time for all the polymer foams. Osteoblast foam constructs created by seeding 6.83 x 10(5) cells/cm2 on foams with 300-500 microns pores resulted in a cell density of 4.63 x 10(5) cells/cm2 after 1 day in culture; they had alkaline phosphatase activities of 4.28 x 10(-7) and 2.91 x 10(-6) mumol/cell/min on Days 7 and 28, respectively; and they had a cell density that increased to 18.7 x 10(5) cells/cm2 by Day 56. For the same constructs, the mineralized matrix reached a maximum penetration depth of 240 microns from the top surface of the foam and a value of 0.083 mm for mineralized tissue volume per unit of cross sectional area. Seeding density was an important parameter for the constructs, but pore size over the range tested did not affect cell proliferation or function. This study suggests the feasibility of using poly(alpha-hydroxy ester) foams as scaffolding materials for the transplantation of autogenous osteoblasts to regenerate bone tissue.

Bone formation by three‐dimensional stromal osteoblast culture in biodegradable polymer scaffolds

Bone tissue engineering

Rat osteoblasts were cultured on films of biodegradable poly(L-lactic acid) (PLLA), 75:25 poly(DL-lactic-co-glycolic acid) (PLGA), 50:50 PLGA, and poly(glycolic acid) (PGA) for up to 14 days. Osteoblasts attached equally well to all the polymer substrates after 8 h in culture. By day 4 in culture, osteoblasts had exceeded confluency numbers, and their proliferation leveled off by day 7. An increase in alkaline phosphatase (ALP) activity from 1.92 (±0.47) × 10−7 for day 7 to 5.75 (±0.12) × 10−7 μmol/cell per min for day 14 was reported for osteoblasts cultured on 75:25 PLGA, which was comparable to that observed for tissue culture polystyrene (TCPS) controls. The ALP activities expressed by osteoblasts cultured on PLLA, 50:50 PLGA, and PGA films did not significantly increase over time. Collagen synthesis for osteoblasts cultured on all polymer substrates was similar to that of TCPS and did not vary with time. The morphology of cultured osteoblasts was not affected by the continuous degradation of the polymer substrates. These results demonstrate that poly(α-hydroxy esters) can provide a suitable substrate for osteoblast culture and hold promise in bone regeneration by osteoblast transplantation. © 1994 John Wiley & Sons, Inc.

Osteoblast function on synthetic biodegradable polymers

Alterations in the normal structure or functions of retinal pigment epithelium (RPE) can result in a number of ocular diseases. Implantation of RPE cells cultured on thin, biodegradable polymer films may provide a means of transplanting an organized sheet of RPE cells with distinct apical/basal characteristics for the restoration of normal RPE function. We have investigated the interactions of human RPE cells with different biodegradable polymer films to assess their suitability as substrates for RPE culture. Four biodegradable polymers were used: low molecular weight (MW) 50:50 poly(DL-lactic-co-glycolic acid) (PLGA); high MW 50:50 PLGA; 75:25 PLGA; and poly(L-lactic acid) (PLLA). Polymer film substrates were manufactured using a solvent casting technique. Human fetal RPE cells (10-16 weeks gestational) were plated on the polymer substrates and the cultures assessed with respect to cell attachment and proliferation. Histological and immunohistochemical studies were performed on the cells after 8 days in culture. RPE cells attached to all the polymers studied after 8 h in culture. After 8 h, 80.2 +/- 9.5% and 82.3 +/- 7.9% of the plated cells were attached to substrates of high MW 50:50 PLGA and 75:25 PLGA, respectively. The cells proliferated on all substrates, and there was about a threefold increase in cell number over the 8-day culture period on all the polymers studied. Immunohistochemistry after 8 days in culture demonstrated RPE cells labeled with a distinct reaction product for cytokeratin in the cell cytoplasm. All the polymers studied were suitable for RPE culture; however, high MW 50:50 PLGA and 75:25 PLGA proved to be the best in terms of manufacturing properties, cell attachment, and proliferation. These polymers can provide a suitable substrate for RPE cell culture and hold promise for the subretinal implantation of organized sheets of RPE cells.

Retinal pigment epithelium cells cultured on synthetic biodegradable polymers.

Donor scarcity precludes the use of pancreatic transplantation to treat type I diabetes. Xenogeneic islet transplantation offers the possibility of overcoming this problem; however, it entails the use of immunoisolation devices to prevent immune rejection of the transplanted islets. These devices consist of a semipermeable membrane, which surrounds the islets and isolates them from the host's immune system, while allowing the passage of insulin and essential nutrients, including glucose. Problems associated with proposed device designs include diffusion limitations, biocompatibility, device retrieval in the event of failure, and mechanical integrity. Microencapsulation appears to be the most promising system of immunoisolation, however, the design of a device suitable for human clinical use remains a challenge. (c) 1994 John Wiley & Sons, Inc.

Susan L. Ishaug

Papers

Bone formation by three‐dimensional stromal osteoblast culture in biodegradable polymer scaffolds

Bone tissue engineering

Osteoblast function on synthetic biodegradable polymers

Retinal pigment epithelium cells cultured on synthetic biodegradable polymers.

Mini-review: Islet transplantation to create a bioartificial pancreas.