Silica-based planar lightwave circuits (PLC) provide various important devices for both optical wavelength-division-multiplexing networks and optical access network. This paper is an overview of recent progress in PLC technology including optical power splitters, arrayed-waveguide gratings, thermooptic switches, and hybrid integrated PLC's.

Silica-based planar lightwave circuits

Silica-based planar lightwave circuits (PLCs) are playing key roles in both optical dense wavelength-division multiplexing networks and optical access networks. This paper provides an outline of PLC technology focusing on passive devices such as arrayed waveguide grating multiplexers.

Silica-based planar lightwave circuits: passive and thermally active devices

To construct large-scale silicon electro-optical switches for optical interconnections, we developed a method using a limited number of power monitors inserted at certain positions to detect and determine the optimum operating points of all switch units to eliminate non-uniform effects arising from fabrication errors. We also introduced an optical phase bias to one phase-shifter arm of a Mach–Zehnder interferometer (MZI)-type switch unit to balance the two operation statuses of a silicon electro-optical switch during push–pull operation. With these methods, a 32 × 32 MZI-based silicon electro-optical switch was successfully fabricated with 180-nm complementary metal–oxide–semiconductor (CMOS) process technology, which is the largest scale silicon electro-optical switch to the best of our knowledge. At a wavelength of 1520 nm, the on-chip insertion losses were 12.9 to 16.5 dB, and the crosstalk ranged from −17.9 to −24.8 dB when all units were set to the ‘Cross’ status. The losses were 14.4 to 18.5 dB, and the crosstalk ranged from −15.1 to −19.0 dB when all units were in the ‘Bar’ status. The total power consumptions of the 32 × 32 switch were 247.4 and 542.3 mW when all units were set to the ‘Cross’ and ‘Bar’ statuses, respectively.

/pdf/32-32-silicon-electro-optic-switch-with-built-in-monitors-5cetn9z8am.pdf

32 × 32 silicon electro-optic switch with built-in monitors and balanced-status units.

A low-loss and high-extinction-ratio silica-based 16/spl times/16 thermooptic matrix switch is demonstrated. The switch, which employs a double Mach-Zehnder interferometer switching unit and a matrix arrangement which reduces the total waveguide length, is fabricated with 0.75% refractive index difference waveguides on a 6-in silicon wafer. The average insertion loss and the average extinction ratio are 6.6 and 55 dB, respectively. The total power consumption is 17 W.

Low-loss and high-extinction-ratio silica-based strictly nonblocking 16/spl times/16 thermooptic matrix switch

This paper describes a silica-based 8/spl times/8 strictly nonblocking thermooptic matrix switch with a high-extinction ratio and low loss. We realized this matrix switch by using a configuration which combines a double Mach-Zehnder interferometer (MZI) switching unit and an N/spl times/N matrix arrangement thus reducing the total waveguide length. The 8/spl times/8 matrix switch was fabricated on a 4-in wafer using planar lightwave circuit technology. We obtained an average extinction ratio of 60.3 dB and an average insertion loss of 5.1 dB. The operating wavelength bandwidth completely covers the gain band of practical erbium-doped fiber amplifiers (EDFAs).

High-extinction ratio and low-loss silica-based 8/spl times/8 strictly nonblocking thermooptic matrix switch

We propose a polarization-controlled free-space photonic switch based on a PI-LOSS switch that has similar insertion loss and lower crosstalk compared to the conventional crossbar switch. We describe a multistage switching network with cross-connected PI-LOSS switch modules that is easier to control and smaller than other strictly nonblocking switch structures. >

T. Nishi

Papers

A polarization-controlled free-space photonic switch based on a PI-LOSS switch