https://cyberleninka.org/article/n/1477609.pdf

Weldability, machinability and surfacing of commercial duplex stainless steel AISI2205 for marine applications – A recent review

Hybrid laser arc welding of thick high-strength pipeline steels of grade X120 with adapted heat input

The main goal of this work was to study the effect of plastic deformation on weldability of duplex stainless steel (DSS). It is well known that plastic deformation prior to thermal cycles can enhance secondary phase precipitation in DSS which can lead to significant change of the ferrite-austenite phase ratio. From this point of view one of the most important phase transformation in DSS is the eutectoid decomposition of ferrite. Duplex stainless steels (DSSs) are a category of stainless steels which are employed in all kinds of applications where high strength and excellent corrosion resistance are both required. This favorable combination of properties is provided by their biphasic microstructure, consisting of ferrite and austenite in approximately equal volume fractions. Nevertheless, these materials may suffer from several microstructural transformations if they undergo heat treatments, welding processes or thermal cycles. These transformations modify the balanced phase ratio, compromising the corrosion and mechanical properties of the material. In this paper, the microstructural stability as a consequence of heat history due to welding processes has been investigated for a super duplex stainless steel (SDSS) UNS S32750. During this work, the effects of laser beam welding on cold rolled UNS S32750 SDSS have been investigated. Samples have been cold rolled at different thickness reduction (e = 9.6%, 21.1%, 29.6%, 39.4%, 49.5%, and 60.3%) and then welded using Nd:YAG laser. Optical and electronical microscopy, eddy’s current tests, microhardness tests, and critical pitting temperature tests have been performed on the welded samples to analyze the microstructure, ferrite content, hardness, and corrosion resistance. Results show that laser welded joints had a strongly unbalanced microstructure, mostly consisting of ferritic phase (~60%). Ferrite content decreases with increasing distance from the middle of the joint. The heat-affected zone (HAZ) was almost undetectable and no defects or secondary phases have been observed. Both hardness and corrosion susceptibility of the joints increase. Plastic deformation had no effects on microstructure, hardness or corrosion resistance of the joints, but resulted in higher hardness of the base material. Cold rolling process instead, influences the corrosion resistance of the base material.

Microstructural and Corrosion Properties of Cold Rolled Laser Welded UNS S32750 Duplex Stainless Steel

In recent years, laser beam welding has found wide applications in many industrial fields. Solidification cracks are one of the most frequently encountered welding defects that hinder obtaining a safe weld joint. Decades of research have shown that one of the main causes of such cracks are the strain and the strain rate. Obtaining meaningful measurements of these strains has always been a major challenge for scientists, because of the specific environment of the measurement range and the many obstacles, as well as the high temperature and the plasma plume. In this study, a special experimental setup with a high-speed camera was employed to measure the strain during the welding process. The hot cracking susceptibility was investigated for 1.4301 stainless steel, and the critical strain required for solidification crack formation was locally and globally determined.

Investigation of solidification cracking susceptibility during laser beam welding using an in-situ observation technique

Strain signatures associated to the formation of hot cracks during laser beam welding of aluminum alloys

Due to significant developments over the last decades, laser beam welding has become a well-established industrial process offering high processing speeds and causing low component distortions. But an important issue currently preventing its intense use, especially in the energy or plant construction sector where high alloy steels are applied, concerns hot crack formation. Although considerable advances in understanding hot cracking mechanisms have been made, most of the known influencing factors are metallurgical in character. The thermo-mechanical effects are barely considered or quantified. Up to the present, there exist numerous hot cracking tests that were however conceived for welding methods other than laser beam welding. Considering the special features of the laser welding process, such as high cooling rates and the narrow process zone, results obtained with other welding techniques and test procedures cannot be transferred to laser beam welding. In this study, the laser beam weldability of vario...

Investigation of the hot cracking susceptibility of laser welds with the controlled tensile weldability test

Manganese alloyed stainless steels represent a cost-effective alternative to conventional CrNi- stainless steels due to strong fluctuations of the market prices for nickel seen during the last years. In CrMnNi steels, nickel is partially replaced by lower-cost manganese and small amounts of nitrogen for stabilization of the austenitic phase. This also brings benefits regarding the mechanical properties, as it results in an increased material strength. Laser beam welding of such materials was investigated for direct comparison with standard CrNi steels. Main emphasis was laid on finding adequate process parameters to achieve a stable welding process and obtain a good weld quality. Two different laser sources, a 4.4 kW Nd:YAG and a 5 kW CO2 laser, were used to weld 1.5 mm stainless steel sheets in continuous wave mode. A high-Mn austenitic (1.4376) and a lean duplex (1.4162) steel, as well as the standard austenitic (1.4301) and duplex (1.4362) grades were selected as test materials. Both butt and lap joint configurations were studied. Experiments were carried out systematically, varying the welding speed, laser power and focal point position in order to determine adequate process windows. The influence of the shielding gas type and flow rate on the process stability and the weld quality were investigated. The effects of weld edge preparation on the weld appearance and quality levels attained were also examined. The obtained welded joints were subjected to radiographic tests for detection of internal imperfections. Also a metallurgical characterization of the samples regarding the resulting phase composition or balance and hardness depending on the welding process parameters was conducted. Furthermore, tensile and potentiodynamic tests were performed to evaluate the mechanical and corrosion properties, respectively. The results provide an insight into the advantages and limitations of the laser beam welding process for joining high-manganese alloyed stainless steels. Conditions for the production of defect-free and corrosion-resistant welds having good mechanical properties could be determined.

Laser Beam Weldability of High-Manganese Austenitic and Duplex Stainless Steel Sheets

High power laser beam welding represents a cost-effective alternative for fast joining of thick components. However, the reliability of the welded structures can be severely affected by solidification crack formation, caused by constructional restraints. Experimental investigations using 15 mm thick plates of the fine grained structural steel S690, welded with a 20 kW fiber laser under different restraint conditions revealed a relationship between hot cracking susceptibility and restraint intensity. Systematic laser welding experiments were conducted in the IRC (Instrumented Restraint Cracking)-test facility, under both free shrinkage as well as defined restraint intensities. In order to assess the stress-strain condition of the weld during solidification which is crucial in the hot crack formation process but also difficult, if not impossible to acquire experimentally, a two-dimensional thermo-mechanical finite element model of the IRC-Test was developed. The results constitute a good approach to explain and understand the detrimental effects of high restraints on hot cracking phenomena during laser beam welding.High power laser beam welding represents a cost-effective alternative for fast joining of thick components. However, the reliability of the welded structures can be severely affected by solidification crack formation, caused by constructional restraints. Experimental investigations using 15 mm thick plates of the fine grained structural steel S690, welded with a 20 kW fiber laser under different restraint conditions revealed a relationship between hot cracking susceptibility and restraint intensity. Systematic laser welding experiments were conducted in the IRC (Instrumented Restraint Cracking)-test facility, under both free shrinkage as well as defined restraint intensities. In order to assess the stress-strain condition of the weld during solidification which is crucial in the hot crack formation process but also difficult, if not impossible to acquire experimentally, a two-dimensional thermo-mechanical finite element model of the IRC-Test was developed. The results constitute a good approach to explain...

Hot cracking in high power laser beam welding of thick high strength structural steels under restraint conditions

Austenitic and austenitic-ferritic CrMnNi-stainless steels are suitable materials in the transport and automotive industry due to their high corrosion resistance and high strength that allows weight and cost savings. This study focuses on the laser weldability of a commercial lean duplex and an austenitic high manganese stainless steel. The impact of different laser sources, i.e. a 5 kW CO2 — and a 4 kW Nd:YAG-laser, and of the main process parameters on the resulting weld quality will be investigated. One important aspect will concern the appearance of weld defects such as pores and hot cracks. The factors causing such internal imperfections will be analysed in order to find effective methods for preventing them. Weld microstructure and the associated corrosion and mechanical properties will be assessed with different techniques and adequate process parameters for high quality welds will be determined. The advantages and limitations of the applied welding processes will be evaluated for future applications.

Vanessa Quiroz

Papers

Investigation of the hot cracking susceptibility of laser welds with the controlled tensile weldability test

Laser Beam Weldability of High-Manganese Austenitic and Duplex Stainless Steel Sheets

Hot cracking in high power laser beam welding of thick high strength structural steels under restraint conditions

Comparison Between Co2 — and Nd:Yag-Laser Beam Welding of High-Strength Crmnni Steels for the Automotive Industry